SNMP-RC210 - Inverter Bxterra - Free user manual and instructions
Find the device manual for free SNMP-RC210 Bxterra in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Line-interactive UPS/inverter with SNMP monitoring |
| Brand | Bxterra |
| Model | SNMP-RC210 |
| Rated Power | 2000 VA / 1600 W |
| Input Voltage | 220-240 VAC |
| Output Voltage | 220-240 VAC (pure sine wave) |
| Output Frequency | 50/60 Hz auto-sensing |
| Transfer Time | 2-4 ms |
| Battery Type | Maintenance-free lead-acid, 24 VDC |
| Communication Interfaces | USB, RS-232, and SNMP slot |
| Protection Functions | Overload, short-circuit, over-temperature, and battery deep-discharge |
| Display | LCD with LED status indicators |
| Dimensions (W x H x D) | 310 x 85 x 430 mm |
| Weight | 11.2 kg |
| Operating Temperature | 0 to 40 °C |
| Noise Level | Less than 45 dB at 1 meter |
| Cooling | Forced-air fan, speed controlled |
| Maintenance and Cleaning | Keep vents clear; wipe with a dry cloth; inspect battery every 3 months |
| Safety Compliance | CE, RoHS, and EN 62040-1 certified |
| Spare Parts and Repairability | User-replaceable batteries; internal circuitry serviceable by certified technicians |
| General Information | Ideal for small servers, networking gear, and point-of-sale systems |
Frequently Asked Questions - SNMP-RC210 Bxterra
How do I install the Bxterra SNMP-RC210 for the first time?
Ensure the inverter is turned off and disconnected from mains. Place it on a flat, stable surface with sufficient ventilation. Connect the battery cables to the internal battery terminals, then plug in the AC input. Turn on the unit and allow it to charge for 4-6 hours before connecting loads.
How can I replace the battery in the SNMP-RC210?
Switch off the inverter and unplug all devices. Remove the front panel cover to access the battery compartment. Disconnect the old battery wires and slide out the battery. Install a new 24V lead-acid battery with the same capacity, reconnect the wires with correct polarity, and replace the cover. Recharge the battery fully before use.
What does the SNMP monitoring feature allow me to do?
The SNMP slot lets you install a network management card (not included) to monitor and control the inverter remotely. You can track voltage, load, and battery status, set up alerts, and perform graceful shutdowns over your network using standard SNMP tools.
How do I connect the SNMP-RC210 to my network?
Insert the optional SNMP card into the slot on the back panel, then connect an Ethernet cable to your switch. Assign an IP address to the card via its web interface, using the default credentials printed on the card label. After configuration, you can access the inverter from your network browser.
Can I configure automatic shutdown of connected devices during a power outage?
Yes, if you use the included USB or RS-232 cable with the bundled software, you can set the inverter to automatically shut down your computer or server after a specified delay when running on battery. The software sends a safe shutdown command before the battery is fully depleted.
What information is shown on the LCD display?
The LCD shows important real-time data: input and output voltage, load percentage, battery charge level, and estimated runtime. LED indicators show AC mode, battery mode, and fault conditions. The display can be toggled using the front button.
How should I clean the inverter and keep it in good condition?
Turn off the inverter and disconnect it from power. Use a soft, dry cloth to wipe the outer surfaces and the display. Do not use any liquids or cleaning sprays. Ensure the air intakes and exhaust vents are free of dust by gently vacuuming them. Inspect the battery terminal every 3 months for corrosion.
How do I perform a self-test on the SNMP-RC210?
With the inverter on and connected to mains, press and hold the TEST button for 2 seconds. The unit will switch to battery for approximately 10 seconds, checking battery condition and internal circuits. The LCD shows 'PASS' if everything is fine, or an error code if a fault is detected.
Can I change the output frequency manually?
The SNMP-RC210 automatically detects 50 or 60 Hz from the input. This is self-sensing and normally does not require manual adjustment. If you need a fixed output frequency for specific equipment, contact technical support as some units offer a configurable setting via the software.
What do the alarm tones mean during operation?
A short beep every 10 seconds indicates battery mode operation. A continuous fast beeping signals low battery or overload. A constant tone with an error code on the LCD indicates a fault. Refer to the manual for the exact beep pattern table, as models may vary.
User questions about SNMP-RC210 Bxterra
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Inverter in PDF format for free! Find your manual SNMP-RC210 - Bxterra and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SNMP-RC210 by Bxterra.
USER MANUAL SNMP-RC210 Bxterra
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Bxterra
Model : SNMP-RC210
Category : Inverter