VT-80300 - Motion detector V-TAC - Free user manual and instructions
Find the device manual for free VT-80300 V-TAC in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Motion Detector |
| Brand | V-TAC |
| Model | VT-80300 |
| Sensor Type | Passive Infrared (PIR) |
| Power Supply | 220-240V AC, 50Hz |
| Rated Load | 1200W max (resistive) / 300W LED |
| Detection Range | Up to 12 meters |
| Detection Angle | 360° (ceiling mount) |
| Adjustable Time Delay | 10 sec – 15 min |
| Adjustable Lux Threshold | 5-2000 lux |
| Mounting Type | Ceiling mounting |
| Recommended Mounting Height | 2.5 – 4 meters |
| Dimensions | Ø 100 x 50 mm |
| Weight | 100 g |
| Material | ABS flame-retardant plastic |
| IP Rating | IP20 (indoor use) |
| Operating Temperature | -20°C to +40°C |
| Certifications | CE, RoHS |
| Safety | Disconnect power before maintenance; clean with dry cloth |
| Spare Parts / Repairability | No user-replaceable parts; contact V-TAC service |
| Warranty | 2 years |
Frequently Asked Questions - VT-80300 V-TAC
How does the VT-80300 motion detector work?
The detector uses passive infrared (PIR) technology to sense heat emitted by people or animals. When a moving object with body temperature crosses the detection zone, the sensor triggers the connected load.
How do I install the motion detector?
Mount the detector on the ceiling at a height of 2.5 to 4 meters. Connect the wiring to a 220-240V AC supply, following the terminal markings. Ensure the detector is fixed securely and the detection lens is not obstructed.
Why does my motion detector keep triggering falsely?
False triggers are often caused by heat sources such as radiators, air vents, or direct sunlight. Check that the detector is not facing these sources and adjust the lux threshold and time delay to reduce sensitivity.
Can I use the motion detector outdoors?
No, this model has an IP20 rating, which means it is only suitable for indoor use. For outdoor applications, choose a detector with a higher IP rating such as IP44 or IP54.
How do I adjust the time delay and light sensitivity?
The detector has two potentiometers: TIME for the output duration (10 sec to 15 min) and LUX for the ambient light threshold (5-2000 lux). Turn them with a small screwdriver to match your requirements.
What type of lighting can the motion detector control?
It can control incandescent, halogen, and LED bulbs with a total load up to 1200W (or 300W for LED). Do not exceed the rated load to avoid damage.
How do I test the motion detector after installation?
Set the LUX knob to the sun mode (daylight) and TIME to its minimum. Power on the detector and walk through the detection area. The connected light should switch on, then turn off after the set delay.
Does the motion detector work through walls?
No, PIR sensors detect infrared radiation only in a line-of-sight area. Walls and other solid objects block the sensor, so the detector must have a clear view of the detection zone.
What should I do if the motion detector turns on during the day?
This usually means the LUX threshold is set too high. Turn the LUX knob counterclockwise until it is below the ambient light level. Test by covering the sensor with your hand and checking if it activates.
Is the VT-80300 compatible with LED bulbs?
Yes, it supports LED loads up to 300W. However, some LED lamps may cause flickering if the load is very low. In that case, use a bypass resistor or choose an LED with a higher minimum load requirement.
User questions about VT-80300 V-TAC
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Motion detector in PDF format for free! Find your manual VT-80300 - V-TAC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. VT-80300 by V-TAC.
USER MANUAL VT-80300 V-TAC
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : V-TAC
Model : VT-80300
Category : Motion detector