2000SI - Paint sprayer Paasche - Free user manual and instructions
Find the device manual for free 2000SI Paasche in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Brand | Paasche |
| Model | 2000SI |
| Product Type | Paint Sprayer (Airbrush) |
| Feed Type | Gravity feed |
| Operation | Double air/paint control |
| Material | Brass and stainless steel |
| Weight | 0.7 lb (317 g) |
| Dimensions | 6 x 4 x 2 inches |
| Fluid Cup Capacity | 1 oz (30 ml) |
| Nozzle Size | 0.53 mm |
| Air Inlet | 1/4 inch BSP |
| Recommended Air Pressure | 15-50 PSI |
| Paint Viscosity Range | Medium to thin |
| Cleaning Method | Disassemble and brush with solvent |
| Maintenance | Lubricate needle and trigger weekly |
| Safety | Disconnect air before servicing |
| Spare Parts | Needles, nozzles, and air caps available |
| Included Accessories | Color cup, wrench, brush, hoses |
| Warranty | 1 year limited |
| Manual | 2 pages, English PDF |
Frequently Asked Questions - 2000SI Paasche
How do I thin paint for the Paasche 2000SI?
Mix your paint with thinner until it reaches the consistency of skim milk. Start with a 2:1 paint-to-thinner ratio and adjust based on your spray pattern.
What air pressure should I use?
Use between 15-50 PSI. Push down on the trigger for air and pull back for paint. Always start at low pressure and increase until you get a fine, consistent spray.
How often should I clean the airbrush?
Clean after every use. Disassemble the needle, nozzle, and air cap and brush off dried paint with a compatible solvent. This prevents clogs and ensures even flow.
Why is my spray pattern sputtering?
A sputtering pattern is usually caused by dried paint in the nozzle or an overfilled cup. Remove the needle and soak the head in solvent; also make sure the cup lid is tight.
How do I replace the needle or nozzle?
Loosen the needle chuck, pull the needle out, and unscrew the nozzle with the included wrench. Install the new parts in reverse order and tighten gently to avoid damage.
Can I spray latex paint?
Correctly thinned acrylic and latex paints work well. Thin them with water or flow enhancer to a fluid consistency and filter to remove lumps.
What should I do if the trigger is sticking?
Remove the trigger, clean the assembly with solvent, and apply a drop of light oil to the friction points. Reassemble and test for smooth action.
How do I achieve a fine line detail?
Use a lower pressure (around 15 PSI), thin paint, and keep the needle stop set to a short pull. Practice on paper to maintain a consistent distance from the surface.
Is the Paasche 2000SI compatible with my compressor?
Any compressor with a 1/4-inch BSP connection and a moisture trap works. Set the regulator to the recommended pressure range.
What is included in the box?
The box includes the airbrush, 1 oz color cup, adjustable wrench, cleaning brush, and a 2-page manual. Additional accessories are sold separately.
User questions about 2000SI Paasche
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Paint sprayer in PDF format for free! Find your manual 2000SI - Paasche and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 2000SI by Paasche.
USER MANUAL 2000SI Paasche
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Paasche
Model : 2000SI
Category : Paint sprayer