RS10mHD - Loudspeaker SAMSON - Free user manual and instructions
Find the device manual for free RS10mHD SAMSON in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Active 2-way studio reference monitor loudspeaker |
| Woofer | 10-inch (254 mm) high-excursion paper cone with rubber surround |
| Tweeter | 1-inch (25 mm) silk dome with protective grille |
| Amplifier | Bi-amplified, total output 120 W (RMS) (80 W LF + 40 W HF) |
| Frequency Response | 50 Hz – 20 kHz (±3 dB) |
| Crossover Frequency | 2.2 kHz, active Linkwitz-Riley 24 dB/octave |
| Inputs | Balanced combo XLR / 1/4" TRS connector, impedance 20 kΩ |
| EQ Controls | HF trim (−2, 0, +2 dB) and LF trim (0, −2, −4 dB) switches |
| Volume Control | Front-panel rotary gain control with detent |
| Enclosure | Bass-reflex design with flared port, medium-density fiberboard (MDF) |
| Dimensions (H × W × D) | 310 × 260 × 244 mm (12.2 × 10.2 × 9.6 in) |
| Weight | 9.5 kg (20.9 lb) |
| Power Supply | Internal power supply, 100–240 V AC, 50/60 Hz, IEC connector |
| Protection | RF interference, overcurrent, overvoltage, overthermal and transient peak protection |
| Mounting | Dual-angle mounting for floor monitoring or vertical studio positioning |
| Accessories Included | Detachable AC power cord, rubber feet, adhesive pads for mounting |
| Maintenance | Dust with dry cloth; do not disassemble; no user-serviceable parts |
| Repairability | Amplifier module and transducers are replaceable by qualified technicians |
Frequently Asked Questions - RS10mHD SAMSON
How should I position the RS10mHD speakers for optimal listening?
Place the speakers at ear level, forming an equilateral triangle with your listening position. For studio use, the tweeters should face your ears, and the speakers should be angled inward equally. Avoid placing them against walls to prevent bass build-up.
Can I connect the RS10mHD to a home stereo receiver or only to professional gear?
The RS10mHD has balanced combo XLR / 1/4-inch TRS inputs, which accept both balanced and unbalanced signals. You can connect a home stereo receiver using a 1/4-inch to RCA cable, but ensure the source is not driving too hot. Start with the volume control low and adjust upward.
What is the purpose of the HF and LF trim switches?
The trim switches adjust the high and low frequency response to compensate for room acoustics or personal taste. HF trim offers ±2 dB at 10 kHz, and LF trim offers 0, −2, or −4 dB at 100 Hz to reduce bass when the speaker is placed near walls.
Is the RS10mHD a powered (active) speaker that needs no external amplifier?
Yes, the RS10mHD is an active speaker with built-in bi-amplification. It contains two dedicated amplifiers for the woofer and tweeter, so you connect line-level audio directly to the speaker and it generates its own power. No external amplifier is needed.
How do I clean and maintain the RS10mHD?
Use a soft, dry microfiber cloth to wipe the cabinet and grilles. Never use solvents or water on the drivers. Periodically check that the power cord is securely connected. Keep the ports free of dust and debris. There are no user-serviceable parts inside.
What should I do if there is a humming or buzzing noise from the speaker?
A hum often comes from ground loops or poor cable shielding. Ensure all audio equipment is on the same power strip, and use high-quality balanced cables. If the hum persists, try disconnecting all inputs and see if it remains. If it does, the issue may be internal and require service.
Can the RS10mHD be used as a floor monitor on stage?
Absolutely. The cabinet has dual-angle mounting points. You can position it at 0° or 45° to act as a wedge monitor, allowing for live sound monitoring while keeping a low profile.
What is the warranty period for the Samson RS10mHD?
Samson typically provides a 2-year limited warranty for speakers, covering defects in materials and workmanship. Verify the exact warranty terms with your local dealer or Samson’s official website, as regional policies may vary.
Can I mount the RS10mHD on a wall or speaker stand?
The RS10mHD is not specifically designed with standard threaded inserts, but it has flat bottom and side surfaces. You can use aftermarket shelving or custom brackets if they can support the weight (9.5 kg / 20.9 lb). For safety, ensure any mounting method is secure and follows local codes.
How long is the power cord and is the voltage adjustable?
The detachable AC power cord is about 2 meters (6.6 ft) long. The internal power supply automatically accepts 100–240 V AC, 50/60 Hz, so you can use it worldwide with the appropriate cord. There is no manual voltage selector required.
User questions about RS10mHD SAMSON
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Loudspeaker in PDF format for free! Find your manual RS10mHD - SAMSON and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. RS10mHD by SAMSON.
USER MANUAL RS10mHD SAMSON
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : SAMSON
Model : RS10mHD
Category : Loudspeaker