Energysilence Aero 10000 Pro - Ceiling fan CECOTEC - Free user manual and instructions

Product Type	Ceiling Fan
Brand	Cecotec
Model	Energysilence Aero 10000 Pro
Blade Diameter	100 cm
Total Height	30 cm
Net Weight	5.2 kg
Power Supply	220-240 V ~ 50 Hz
Maximum Power	50 W
Number of Speeds	3
Summer/Winter Reverse Function	Yes
Remote Control Included	Yes, with wired receiver
Noise Level	< 35 dB at speed 1
Blade Material	ABS
Mounting Type	Ceiling (requires ceiling mounting)
Maintenance and Cleaning	Dust regularly with a soft dry cloth. Do not use chemical or abrasive products.
Safety	Installation must be carried out by a qualified electrician. Do not insert objects into the fan while it is running.
Spare Parts	Available on the Cecotec website or from customer service.
Repairability	Repairability score: 7.8/10 (estimate)
Warranty	2 years

Frequently Asked Questions - Energysilence Aero 10000 Pro CECOTEC

How to install the Cecotec Energysilence Aero 10000 Pro fan?

Installation must be carried out by a qualified electrician. Follow the provided instructions: attach the mounting plate to the ceiling, connect the electrical wires (phase, neutral, ground) and assemble the blades. Use the remote control after installation.

How to clean the fan?

Dust the blades and motor with a soft dry cloth. Never use chemicals, abrasives, or water directly on the motor.

How to reverse the rotation direction for winter?

Use the reverse button on the fan housing or the remote control. In winter mode, the blades rotate clockwise to redistribute heat from the ceiling to the floor.

The fan is noisy, what should I do?

Check that the blades are balanced and properly attached. Ensure the fan is correctly installed and screws are tightened. If noise persists, contact Cecotec customer service.

The remote control is not working, how to fix?

Check the remote control battery (type CR2032). Reset the receiver by turning off the fan power for 10 seconds. Make sure the remote code matches the receiver code.

What are the exact dimensions of the fan?

The blade diameter is 100 cm and the total height is approximately 30 cm. Check the clearance around the fan before installation.

Can this fan be used outdoors?

No, this model is designed for indoor use only. Using it outdoors exposes the motor to moisture and may cause malfunction or danger.

How to adjust the fan speed?

Use the remote control or wall switch (if connected) to select one of the 3 available speeds. Speed 1 is the quietest, speed 3 provides maximum airflow.

Where to find spare parts for this model?

Spare parts (blades, remote control, receiver) are available on the official Cecotec website or through their after-sales service. Check the manual for references.

How to turn off the fan completely?

Use the remote control to put the fan in standby or turn off power via the wall switch. For a complete shutdown, disconnect the circuit breaker.

USER MANUAL Energysilence Aero 10000 Pro CECOTEC

Safety instructions 7

1. Parts and components 43

2. Before use 43

3. Assembly 44

4. Operation 45

5. Cleaning and maintenance 46

6. Troubleshooting 46

7. Technical specifications 47

8. Disposal of old electrical and electronic appliances 48

9. Technical support and warranty 48

10. Copyright 48

SOMMAIRE

Read these instructions thoroughly before using the device. Keep this instruction manual for future reference or new users.

• This appliance can be used by children aged 8 years and above and people with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children must not play with the appliance. Cleaning and user maintenance should not be carried out by unsupervised children.
• Keep a minimum distance of 2.3 cm between the fan blades and the floor.

• Keep a minimum distance of 76 cm between the fan blades and the wall or any other object.

• Make sure the appliance is unplugged from the power supply before cleaning or user maintenance.

• This device is designed for domestic use only and is not intended for bars, restaurants, farmhouses, hotels, motels, and offices.
• Make sure that the mains voltage matches the voltage stated on the appliance marking and that the wall outlet is earthed.
• If the power cord is damaged, it must be replaced by the official Cecotec Technical Support Service to avoid any type of danger.
• Do not use the appliance if its cord or housing are damaged, nor after it malfunctions or has been dropped or damaged in any way.
• The appliance must be installed in accordance with national wiring regulations.
• Never insert objects or body parts between the rotating fan blades.
• To reduce the risk of injury, attach the fan directly to the support structure of the building as indicated in this manual and use only parts and components provided and recommended by Cecotec.
• Cut off the power completely before installing or repairing the fan to avoid the risk of electric shock.
• The electrical wiring must be in accordance with the local regulations.
• The cable must be properly earthed to avoid possible accidents.
• The appliance must be installed in accordance with national wiring regulations.
• Never install the fan in a damp or wet room.

• Be careful when near the rotating fan blades.

• To adjust the speed of the fan blades, only use the means for speed control provided by Cecotec.

• Do not bend the blade-attachment system during the installation or cleaning process.
• Cleaning and maintenance must be carried out according to this instruction manual to make sure the appliance works properly. Turn off and unplug the appliance before cleaning it.
• Make sure the fan is not placed close to curtains or other objects it may become entangled with.
• In order to ensure your children's safety, please keep all packaging (plastic bags, boxes, polystyrene, etc.) out of their reach.
• It is recommended that two people install the appliance.
• This appliance is designed for indoor use.

Instructions on batteries

• Battery ingestion can cause burns, soft-tissue perforation, and death. It can cause severe burns within two hours of the ingestion.
• In case of battery ingestion, please seek medical attention immediately.
• Do not allow children to replace batteries without adult supervision.
• Do not disassemble, open, or damage the batteries.
• Keep the batteries out of the reach of children. Pay particular attention to small batteries. In case of battery ingestion, please seek medical attention immediately.
• Do not expose batteries to heat or fire. Avoid storage in direct sunlight.
• Do not short-circuit an element or a battery. Do not store batteries in an untidy manner, in a box, or drawer where they

can short-circuit each other or be short-circuited by other metal objects.

• Both batteries and cells can leak under extreme conditions. In the event of a battery leak, keep your skin and eyes away from the liquid. If the liquid gets into contact with skin, wash immediately with soap and water. If the liquid gets into the eyes, wash them immediately with clean water for a minimum of 10 minutes and seek medical attention. Wear gloves to handle the battery and dispose of it immediately in accordance with local regulations.
• Pay attention to the positive (+) and negative (-) marks on the batteries and the remote-control compartment to ensure they are inserted correctly.
• Do not use any batteries that are not designed for use with the appliance.
• Do not mix batteries of different manufacture, capacity, or size. Children should be allowed to handle the batteries only under adult supervision.
• Always buy recommended batteries.
• Keep the batteries clean and dry. Wipe the battery terminals with a clean, dry cloth if they become dirty.
• Keep the original instruction manual for future reference.
• Whenever possible, remove the batteries when not in use.

INSTRUCTIONS DE SÉCURITÉ

1. Mounting bracket
2. Canopy
3. Downrods
4. Decorative cover
5. Coupling cover
6. Motor
7. Blades
8. Blade bracket
9. Lamp bracket
10. Lampshade

11. Assembly kit

12. Remote control and remote-control receiver

NOTE:

The graphics in this manual are schematic representations and may not exactly match the device.

2. BEFORE USE

• This appliance is packaged in a way as to protect it during transport. Take the appliance out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place. This will help you prevent damage to the appliance when transporting it in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
• Make sure all parts and components are included and in good conditions. If there is any piece missing or in bad conditions, contact the official Cecotec Technical Support Service immediately.

Box content

• Fan
• Instruction manual
• Assembly kit
• Remote control
• Remote control batteries (2 x AAA)

ENGLISH

3. ASSEMBLY

Installation of the mounting bracket

Fig. 2 key:

A Concrete ceiling

B Wooden ceiling

1. Drill a 8 mm hole in the ceiling and insert the bolt. Align the mounting bracket with the hole and tighten it with the nut.
2. Remove the clevis pin and clevis from the downrod. Fig. 3
3. Slide the downrod through the canopy and the coupling cover. Fig. 4
4. Pass the fan wires and the earth wire through the downrod. Fig. 5
5. Loosen the screws of the downrod bracket and then place the downrod in its bracket. Align the holes in the clevis pin of the downrod with the holes in the bracket. Make sure to insert the straight part of the clevis pin through the hole in the end of the clevis pin and press until the crimped part snaps into position. Fig. 6.
6. Finally, retighten the screws. Fig. 7

WARNING

It is very important that the downrod bracket clevis pin is correctly installed and that the screws are tightened securely. If the pin, clevis, or screws are not correctly positioned, the fan may fall down.

Installing the blades

1. Place the blade bracket. Remove the corresponding screws from the assembly kit and screw them. Fig. 8
2. Place the blades on the motor assembly. Fig. 9
3. Remove the screws from the motor assembly. Place the lamp bracket on the motor assembly. Next, tighten the screws. Fig. 10

Hanging the fan

1. Lift the fan carefully and install the downrod and hanging ball into the mounting bracket attached to the ceiling. Make sure that the groove in the hanging ball is properly aligned with the tab on the mounting bracket. Fig. 11

Fig. 11 key:

1. Slot
2. Clip
3. Mounting bracket

Warning: the fan must be placed at a minimum distance of 230 cm from the floor.

Connection of the remote-control receiver

1. Insert the receiver into the mounting bracket as shown in Fig. 12.

Warning: to avoid the risk of electric shock, be sure to disconnect the mains supply from the switchboard before connecting the cables.

Installing the LED light

1. Attach the lampshade to the motor shaft. Fig. 13

Fig. 13 key:

1. Motor shaft
2. Lampshade

Receiver wiring

You must follow the electrical diagram shown in Fig. 14.

Installing the canopy

1. Install the canopy by screwing both screws as shown in Fig. 15.

4. OPERATION

This fan can be operated with the remote control.

Remote control

Fig. 16

1. Power indicator light
2. Speed setting
3. Fan OFF button
4. Blade reversal button
5. Natural Breeze button

6. Timer buttons

7. The indicator will light up while the appliance is in operation.

8. Use the speed buttons to select the power level.
9. Press the off button to switch the appliance off.
10. Use the timer buttons to select the operation time of the appliance. The fan will turn off once the selected time has elapsed.

Winter/Summer function

- Use the blade reversal button to activate the reverse rotation.

ENGLISH

• Winter function: the blades start to rotate clockwise, causing warm air to be distributed throughout the room.
• Summer function: the blades start to rotate counterclockwise, generating a cool breeze.

Note

1. If the remote control cannot control the receiver, check if the batteries make contact, if they are inserted correctly and if they are not flat.
2. If the remote control cannot control the receiver, check if there are other appliances operating with a remote control nearby, as they may cause interference. If you remove these appliances from the room where the fan is located, the remote control will work properly again.
3. Use this appliance with the correct voltage. If the voltage is too low, the remote control will not work.
4. If you are not going to use the remote control for a long period of time, remove the batteries.

5. CLEANING AND MAINTENANCE

• Clean the fan regularly.
• When cleaning, only use a soft brush or lint-free cloth to avoid scratching the finish.
• Abrasive cleaning agents are not necessary and should be avoided in order not to damage the finish.

RECOMMENDATION:

Periodically check that the blades are securely fastened to the motor with the screws.

WARNING:

Do not use solvents to clean the fan. Doing so may result in a risk of electric shock.

6. TROUBLESHOOTING

Wobble

Note that not all ceiling fans are the same (not even those that are the same model), some move more than others. The fact that the fan moves a couple of centimetres does not indicate that it will fall over.

Even if all blades are ballasted and grouped by weight, it is impossible to completely avoid wobble. This is not a problem. Ceiling fans tend to move during operation.

To reduce wobble, try the following:

• Check that all of the blade mounting screws are tightened and secure.
• Fan wobble may be caused by the unevenness of the fan blades. To check the blade level, measure the distance from each blade tip to the ceiling.

If measurements are irregular

• Be sure the blade mount screws are not too tight or too loose, which may cause wobbling due to an unlevelled blade tip.
• A deformed blade can cause wobbling. Check by removing the blade and placing on a flat surface.
• Blade tracking may be checked simply by use of a household ruler. Place the ruler vertically against the ceiling and even with the outside leading edge of a blade. Note the distance of the edge of a blade compared to the others. Turn the blade slowly by hand to check the remaining blades.
• If a blade is not in alignment, the blade is either out of shape, warped or the blade screws are not evenly tightened or either loose.

7. TECHNICAL SPECIFICATIONS

Product reference: 08568

Product: EnergySilence Aero 10000 Pro

Voltage: 220-240 V

Frequency: 50 / 60 Hz

Power: 80 W

Description	Symbol	Value	Unit
Fan maximum flow	F		m^3/min
Fan power consumption	P		W
Service value	SV		(m^3/min)/W
Power consumption on standby mode	P_SB		W
Fan sound power level	L_WA		dB (A)
Maximum air speed	C		m/seg
Service value measurement standard	IEC 60879
Contact details to obtain more information	Cecotec Innovaciones SL.Av. Reyes Católicos, No 60, 46910, Alfafar(Valencia, Spain)

ENGLISH

Technical specifications may change without prior notification to improve product quality. Made in China | Designed in Spain

8. DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES

This symbol indicates that, according to the applicable regulations, the product and/or batteries must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the cells/batteries/accumulators and take them to a collection point designated by the local authorities.

Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.

Compliance with the above guidelines will help protecting the environment.

9. TECHNICAL SUPPORT AND WARRANTY

Cecotec shall be liable to the end user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions, and deadlines established by the applicable regulations.

It is recommended that repairs be carried out by qualified personnel.

If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact the official Cecotec Technical Support Service at [phone].

10. COPYRIGHT

The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.

1. PIÈCES ET COMPOSANTS

Image 1:

Se as medidas forem irregulares:

6. PROBLEEMOPLOSSING

Ventilator schommelt

Product: EnergySilence Aero 10000 Pro

Spanning :200 - 240 V

Fig./Img./Abb./Afb./ Rys./Obr. 2

Fig./Img./Abb./Afb./Rys./Obr. 3

Fig./Img./Abb./Afb./Rys./Obr. 4

Fig./Img./Abb./Afb./Rys./Obr. 5

Fig./Img./Abb./Afb./Rys./Obr. 6

Fig./Img./Abb./Afb./ Rys./Obr. 7

Fig./Img./Abb./Afb./Rys./Obr. 8

Fig./Img./Abb./Afb./ Rys./Obr. 9

Fig./Img./Abb./Afb./Rys./Obr. 10

Fig./Img./Abb./Afb./ Rys./Obr. 11

Fig./Img./Abb./Afb./ Rys./Obr. 12

Fig./Img./Abb./Afb./ Rys./Obr. 13

Controller wiring Diagram

Fig./Img./Abb./Afb./ Rys./Obr. 14

Fig./Img./Abb./Afb./Rys./Obr. 15

Fig./Img./Abb./Afb./Rys./Obr. 16

www.cecotec.es