VIV700.1 - Receiver Memphis Audio - Free user manual and instructions
Find the device manual for free VIV700.1 Memphis Audio in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Monoblock Car Audio Amplifier |
| Model | VIV700.1 |
| Brand | Memphis Audio |
| RMS Power Output | 700 Watts x 1 @ 1 Ohm |
| Peak Power Output | 1400 Watts |
| Frequency Response | 20 Hz - 250 Hz |
| Damping Factor | >200 |
| Signal-to-Noise Ratio | >100 dB |
| Total Harmonic Distortion | <0.05% |
| Low Pass Filter | Variable 40 Hz - 250 Hz |
| Subsonic Filter | Fixed 25 Hz |
| Bass Boost | 0-18 dB @ 45 Hz |
| Input Sensitivity | 200 mV - 8 V |
| Remote Level Control | Included (wired remote) |
| Speaker Impedance | 1 - 8 Ohms |
| Power Supply Voltage | 12 V DC (10-16 V) |
| Fuse Rating | 60A (ATO blade) |
| Dimensions (L x W x H) | 12.6 x 7.1 x 2.2 inches |
| Weight | 5.5 lbs |
| Recommended Wire Gauge | 4 AWG power/ground |
| Protection Features | Thermal, overload, short circuit |
| Mounting Type | Chassis mount (screws included) |
| Cooling | Convection with heatsink fins |
| Cleaning Instructions | Wipe with dry cloth; avoid moisture |
| Safety Warnings | Disconnect battery before installation; use proper fusing |
Frequently Asked Questions - VIV700.1 Memphis Audio
What is the RMS power output of the Memphis Audio VIV700.1?
The Memphis Audio VIV700.1 delivers 700 Watts RMS at 1 Ohm, and up to 1400 Watts peak.
What impedance loads can the VIV700.1 handle?
The amplifier is stable down to 1 Ohm and can handle up to 8 Ohms. It is not 2-ohm stable in bridged mode as it is a monoblock.
How do I correctly wire the VIV700.1 amplifier?
Use 4 AWG power and ground wires with a 60A fuse. Connect power to battery positive, ground to chassis ground, and remote turn-on to head unit. Speaker output: connect subwoofer(s) to + and - terminals observing total impedance of 1-8 ohms.
Does the VIV700.1 come with a remote subwoofer level control?
Yes, it includes a wired remote level control for adjusting bass output from the driver's seat.
What is the recommended power wire gauge for this amplifier?
4 AWG wire is recommended for power and ground connections to handle up to 60 amps of current draw.
How do I set the gain on the VIV700.1?
Start with gain at minimum, play a test tone at 40-50 Hz, increase head unit volume to about 3/4 max, then adjust gain until you hear distortion, then back off slightly. Use a multimeter for precise voltage setting.
Is the VIV700.1 stable at 2 ohms?
Yes, the amplifier is stable at 2 ohms and will produce around 400-500 Watts RMS at 2 ohms.
Can the VIV700.1 be bridged?
No, this is a monoblock amplifier and is already a single channel. It cannot be bridged further.
What is the frequency response of the VIV700.1?
The amplifier has a frequency response of 20 Hz to 250 Hz, optimized for subwoofer use.
What should I do if the amplifier has no sound?
Check power and ground connections, ensure remote turn-on wire has 12V, verify fuse is intact, check speaker wiring for shorts, and confirm input signal from head unit. If protection light is on, check for overheating or short circuit.
User questions about VIV700.1 Memphis Audio
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual VIV700.1 - Memphis Audio and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. VIV700.1 by Memphis Audio.
USER MANUAL VIV700.1 Memphis Audio
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Memphis Audio
Model : VIV700.1
Category : Receiver