MX150.2-24V - Receiver Memphis Audio - Free user manual and instructions
Find the device manual for free MX150.2-24V Memphis Audio in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | 2-Channel Amplifier |
| Brand | Memphis Audio |
| Model | MX150.2-24V |
| Power Supply Voltage | 24V DC (nominal) |
| RMS Power Output (per channel) | 150W @ 4 ohms |
| Peak Power Output (per channel) | 300W @ 4 ohms |
| Number of Channels | 2 |
| Frequency Response | 20 Hz – 20 kHz |
| Total Harmonic Distortion (THD) | < 0.05% |
| Signal-to-Noise Ratio | > 90 dB |
| Input Sensitivity | 200 mV – 6 V |
| Dimensions (W x H x D) | 8.5 x 2.0 x 6.0 in (216 x 51 x 152 mm) |
| Weight | 2.0 lb (0.9 kg) |
| Fuse Rating | 25 A (external) |
| Speaker Impedance | 4 ohms (stereo), 8 ohms (bridged) |
| Bridgeable | Yes, up to 300W RMS @ 8 ohms |
| Crossover Type | Low-pass (LPF) and high-pass (HPF) filters |
| Crossover Frequency Range | 50 Hz – 250 Hz |
| Input Type | RCA line inputs |
| Output Type | Speaker wire terminals |
| Protection Features | Thermal, over-current, DC offset, short circuit |
| Operating Temperature | -20°C to 60°C |
| Recommended Use | Marine, RV, heavy-duty vehicles (24V systems) |
| Maintenance | Wipe with dry cloth; ensure ventilation slots are clear |
| Safety Precautions | Disconnect power before servicing; use proper fuse size |
Frequently Asked Questions - MX150.2-24V Memphis Audio
What is the MX150.2-24V amplifier used for?
This is a 2-channel amplifier designed for 24V electrical systems commonly found in trucks, RVs, and marine applications. It can power two speakers or one bridged subwoofer.
Can I bridge the amplifier for more power?
Yes, the MX150.2-24V is bridgeable. When bridged into a single channel, it delivers up to 300W RMS at 8 ohms. Ensure your subwoofer is compatible.
What size fuse do I need?
Use an external 25A fuse on the power wire close to the battery. Never exceed this rating to protect the amplifier.
How do I adjust the crossover?
The amplifier has built-in low-pass (LPF) and high-pass (HPF) filters. Use a small flathead screwdriver to adjust the crossover frequency between 50 Hz and 250 Hz.
What is the recommended speaker impedance?
For stereo operation, use 4-ohm speakers per channel. In bridged mode, the minimum impedance is 8 ohms. Lower impedances may cause overheating.
Can I install this in a car with a 12V system?
No, this amplifier is designed specifically for 24V systems. Using it on 12V will result in significantly reduced power output and may cause issues. Use a 12V model instead.
Does it work with marine speakers?
Yes, the amplifier is suitable for marine environments if mounted in a dry location. It has corrosion-resistant connectors but is not fully waterproof.
How do I clean the amplifier?
Unplug the power, then wipe the exterior with a soft, dry cloth. Do not use any liquids or cleaners that could enter the ventilation slots.
What should I do if the amplifier goes into protection mode?
Protection mode indicates an issue such as overheating, short circuit, or over-current. Check speaker wiring, ensure proper ventilation, and verify the impedance load. If the problem persists, consult a professional.
Where can I find the user manual?
The user manual for the Memphis Audio MX150.2-24V is available for free download on notice-facile.com in PDF format.
User questions about MX150.2-24V Memphis Audio
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual MX150.2-24V - Memphis Audio and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. MX150.2-24V by Memphis Audio.
USER MANUAL MX150.2-24V Memphis Audio
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Memphis Audio
Model : MX150.2-24V
Category : Receiver