DS-K1107EK - Access Control System Hikvision - Free user manual and instructions
Find the device manual for free DS-K1107EK Hikvision in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Access Control Keypad Reader |
| Model | DS-K1107EK |
| Brand | Hikvision |
| Reader Technology | RFID (125 kHz) + Keypad |
| Keypad | 12-key tactile keypad with backlight |
| Card Type | EM (125 kHz) compatible |
| Read Range | Up to 5 cm (card dependent) |
| Power Supply | 12 VDC, 500 mA |
| Dimensions (W × H × D) | 87 mm × 87 mm × 30 mm |
| Weight | Approx. 120 g |
| Material | Polycarbonate (PC) + ABS |
| Protection Rating | IP65 (weatherproof) |
| Operating Temperature | -20°C to +60°C |
| Storage Temperature | -30°C to +70°C |
| Interface | Wiegand 26/34 (output) |
| Indicator | Bi-color LED (red/green) and buzzer |
| Tamper Protection | Tamper switch (detects removal) |
| Max. Connection Distance | Up to 100 m (Wiegand line) |
| Maintenance | Clean with soft dry cloth; avoid solvents |
| Security Features | Tamper alarm, encrypted Wiegand (optional) |
| Spare Parts | Mounting bracket, screws, cable gland |
| Reparability | Limited; contact Hikvision support or authorized service |
Frequently Asked Questions - DS-K1107EK Hikvision
How do I wire the DS-K1107EK to my access controller?
Connect the Wiegand D0 (green) and D1 (white) wires to the corresponding inputs on your controller. Power (12V DC) is supplied via red (V+) and black (GND) wires. The tamper switch wires (blue/violet) can be used as alarm inputs.
Can I use this keypad with 26-bit or 34-bit Wiegand?
Yes, the DS-K1107EK supports both Wiegand 26 and 34-bit formats. The output format can be selected via a software tool or default setting, depending on your controller.
What types of cards does the reader accept?
The reader works with 125 kHz EM compatible cards (e.g., EM4100) and keypad codes. It does not support higher frequency cards like 13.56 MHz.
How do I change the master code or add users?
By default, the master code is 123456. Enter it followed by # to access programming. Then follow the manual to add user PINs or cards. For example: Master code # + 0 + new PIN # (add user).
The keypad is not lit; is it broken?
The backlight activates only when a key is pressed or when power is first applied. If it never lights, check the 12V DC power supply and wiring. The LED indicator should still show status.
How far can the reader be from the controller?
The maximum recommended distance for Wiegand wiring is 100 meters (328 feet). For longer runs, use a shielded cable and consider a signal booster.
Can I mount the DS-K1107EK outdoors?
Yes, it has an IP65 rating, meaning it is dust-tight and protected against water jets. Ensure the rear seal is intact and the cable gland is tightened to maintain weatherproofing.
What does the red/green LED indicate?
Green steady: access granted. Red steady: access denied. Red blinking: tamper alarm or programming mode. Off: no power.
How do I reset the device to factory settings?
Power off the reader. Press and hold the # key while reapplying power. Continue holding for 5 seconds until the buzzer sounds. Release; the reader resets to default settings (master code 123456).
Is the keypad compatible with Hikvision access controllers only?
The DS-K1107EK outputs standard Wiegand signals, so it works with most Wiegand-compatible controllers, not just Hikvision. For encrypted Wiegand, use with Hikvision controllers that support it.
User questions about DS-K1107EK Hikvision
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Access Control System in PDF format for free! Find your manual DS-K1107EK - Hikvision and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. DS-K1107EK by Hikvision.