VPC-10 - Electrical tester Amprobe - Free user manual and instructions
Find the device manual for free VPC-10 Amprobe in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Electrical Tester / Voltage Tester |
| Brand | Amprobe |
| Model | VPC-10 |
| Dimensions | Approx. 150 x 70 x 30 mm |
| Weight | Approx. 200 g (with batteries) |
| Power Supply | 1 x 9V battery (6LR61 or equivalent) |
| Display | Backlit LCD, 3-digit |
| Voltage Range AC | 12 V to 600 V (50/60 Hz) |
| Voltage Range DC | 12 V to 600 V |
| Resistance Range | 0 to 200 kΩ |
| Continuity Test | Yes, with audible buzzer |
| Diode Test | Yes |
| Input Impedance | ≥ 10 MΩ |
| Overvoltage Category | CAT III 600 V |
| Safety Standards | IEC 61010-1, EN 61243-3 |
| Operating Temperature | 0°C to 40°C |
| Storage Temperature | -10°C to 50°C |
| Humidity | ≤ 80% RH non-condensing |
| Maintenance & Cleaning | Clean with a damp cloth; do not use solvents. Store in dry place. |
| Safety Precautions | Do not use on circuits above 600 V. Wear appropriate PPE. Do not use if damaged. |
| Spare Parts & Repairability | Contact Amprobe service center for parts and repairs. No user-serviceable parts inside. |
| General Information | Compact, handheld tester suitable for residential and commercial electrical troubleshooting. |
Frequently Asked Questions - VPC-10 Amprobe
How do I test AC voltage with the VPC-10?
Turn the selector dial to the AC voltage range (V~). Insert the test leads into the input jacks (red to V/Ω, black to COM). Touch the probes to the circuit. The display will show the voltage. Ensure the circuit is energized.
How do I test continuity?
Turn the dial to the continuity/beep setting (often marked with a diode or sound wave symbol). Insert leads as above. Touch probes together to confirm beep. Then test the circuit; a continuous path will produce a tone.
What battery does the VPC-10 use?
It uses one 9V battery (6LR61 or equivalent). To replace, open the battery compartment at the back and connect the battery snap.
What is the maximum voltage the VPC-10 can measure?
The VPC-10 can measure up to 600 V AC or DC. It is rated for CAT III 600 V, meaning it can be used on distribution circuits.
How do I clean the tester?
Clean the outer casing with a soft cloth dampened with water or mild soap. Do not use abrasive cleaners or solvents. Avoid getting moisture inside the device.
Can I measure resistance with the VPC-10?
Yes. Turn the dial to the Ω setting. Ensure the circuit is de-energized. Connect probes across the resistor or circuit. Read the resistance value on the display.
What safety precautions should I take?
Always wear insulated gloves and safety glasses. Do not use on live circuits above 600 V. Inspect test leads for damage before use. Use only the specified fuses (if any). Follow the manual's safety instructions.
Why does the display show 'OL'?
'OL' means overload or open loop. It indicates the measurement exceeds the range, the probes are not connected properly, or the circuit is open (in continuity/resistance mode). Check connections and range.
How do I replace the battery?
Turn off the tester and disconnect leads. Open the battery compartment screw at the back. Remove old battery, snap in new 9V battery, close compartment, and tighten screw.
What is the purpose of the hold/backlight button?
The hold button freezes the current reading on the display. The backlight button toggles the display illumination for dark environments. Press and release to activate each function.
User questions about VPC-10 Amprobe
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Electrical tester in PDF format for free! Find your manual VPC-10 - Amprobe and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. VPC-10 by Amprobe.
USER MANUAL VPC-10 Amprobe
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Amprobe
Model : VPC-10
Category : Electrical tester