HJA45B-GDBL - Refrigerator Helkama - Free user manual and instructions

Product Type	Refrigerator
Brand	Helkama
Model	HJA45B-GDBL
Color	White
Dimensions (H x W x D)	85 cm x 55 cm x 55 cm
Weight	25 kg
Voltage	220-240 V
Frequency	50 Hz
Energy Efficiency Class	A+
Annual Energy Consumption	150 kWh
Climate Class	N-ST
Refrigerant	R600a
Noise Level	42 dB
Net Capacity (Fridge)	120 L
Net Capacity (Freezer)	15 L
Defrost System	Manual
Temperature Control	Adjustable thermostat
Interior Light	Yes
Reversible Door	Yes
Number of Shelves	3
Number of Door Bins	2
Adjustable Legs	Yes
Power Cord Length	1.8 m

Frequently Asked Questions - HJA45B-GDBL Helkama

What is the optimal temperature setting for the refrigerator?

The optimal temperature for the refrigerator compartment is between 3°C and 5°C. Adjust the thermostat dial to achieve this range.

How do I reverse the door opening direction?

The door is reversible. Unscrew the hinges, swap the door handles, and reattach the hinges on the opposite side. Details are provided in the installation section of the manual.

Why is my refrigerator making unusual noises?

Normal noises include a soft hum from the compressor, clicking of the thermostat, and water flow sounds. If loud rattling occurs, ensure the fridge is level and not touching walls or cabinets.

How often should I defrost the freezer?

Defrost the freezer compartment when the ice layer reaches 5 mm thickness. This typically occurs every few months. Turn off the appliance and leave the door open to melt ice.

What is the annual energy consumption of this model?

The estimated annual energy consumption is 150 kWh, based on standard usage conditions. This results in low running costs.

Can I install the refrigerator in an unheated garage?

This model has a climate class of N-ST, meaning it operates safely between 16°C and 38°C. Avoid placing it in areas below 16°C to prevent performance issues.

How do I clean the condenser coils?

Unplug the refrigerator and locate the coils at the back or bottom. Use a vacuum cleaner with a soft brush attachment to remove dust. Clean every 6 months for efficiency.

What should I do if the refrigerator stops cooling?

Check if the power cord is plugged in, the circuit breaker is on, and the thermostat is set correctly. If still not cooling, contact customer support as the compressor may need inspection.

Where can I purchase spare parts like shelves or door gaskets?

Spare parts are available through authorized Helkama service centers or online retailers. Refer to the 'Spare Parts' section in the manual for part numbers.

How long is the warranty period?

The standard warranty period for Helkama fridges is 2 years from the date of purchase. Register your product online to activate the warranty.

USER MANUAL HJA45B-GDBL Helkama

CE declaration of conformity

This appliance has been manufactured to the strictest standards and complies with all

applicable legislation, Low Voltage Directive (LVD) and Electromagnetic Compatibility (EMC).

• Read this user manual before using the product. It will help you to use it and extend its life.
• Save the user manual for later use if this should become necessary and ensure the instructions are followed if the product changes hands.

This user manual contains safety instructions, operating instructions, installation instructions, troubleshooting tips, etc.

Before calling for service:

• Review the troubleshooting tips section. This will help you solve some of the problems yourself.
• If you cannot solve the problems yourself, call for help from professional technicians.

When you call:

Please state the full reference of the device (model, type, serial number). This is on the rating plate attached to the appliance. It can be placed inside the product, on the back or bottom. You must state where and which retailer the product was purchased from, as we may need this information for the purchase.

Unauthorized calling of technical service:

Please check the section for troubleshooting before service is called. If the demand is unjustified, it is the customer's responsibility to pay the costs associated with calling.

Right of complaint for commercial use:

Commercial purchases are any purchase of products that are not to be used in households, but are used for business or business-like purposes (restaurant, café, canteen, etc.) or other use that includes several users.

The complaint deadline covers only brand new products. The complaint period is calculated from the date of purchase, provided that a receipt, bill, or equivalent is kept. The right to complain only covers defects in material (

The right to complain does not include:

• Normal wear and tear, failure, or damage caused directly or indirectly by mishandling, abuse, careless handling, inadequate maintenance, damage caused by not observing the user manual, incorrect installation, installation and connection, variations or electrical disturbances. Repair carried out by other than Scandomes technicians.
• Compensation for any consequential damage, including damage to other objects, etc., unless otherwise determined by law.

Transport damage that is detected at the time of the dealer's delivery to the client is a matter between the customer and the dealer. In cases where the customer is responsible for the transport of the product, the supplier assumes no obligations for transport damage. Possible transport damage must be reported immediately and within hours after the item has been delivered. Otherwise, the customer's claim may be

Important!

Please be aware that, as a result of constant development and updating, the manufacturer may make changes without prior notice.

This is an original manual.

Safety instructions

Your safety and that of others is important.

Dear Customer! Thank you for choosing Scanco.

This manual is designed to provide you with detailed information on safety instructions, operating instructions, installation instructions, and tips for problem solving. Before using the cooler, please read this manual fully to understand how to install and operate it safely.

This user manual was originally written in English.

Safety measures

The purpose of the security measures in this guide is to ensure safe and proper use of the device to minimize the risk of serious injury and damage to you or others. The security measures are divided into WARNINGS and C

How wrong handling of the device may lead to injury are indicated under the heading "WARNING". How also cause serious damages are listed under the heading "CAUTION". Both types of security must be strictly observed to ensure the security.

Text after exclamation marks contains information that is strictly observed. After reading the instructions, store them in an easily accessible place where this product can easily find them.

Keep this manual for future reference, and ensure it is transferred with the cooler if the appliance changes ownership.

Note that all electrical appliances can cause danger. Never store explosives, flammable or volatile substances

such as gas, petrol, ether or similar substances in the appliance, as an explosion may occur and fire. Never use flammable cans or crates if combustible substances are near the appliance.

WARNING: Do not store explosives, e.g. Aerosol cans with flammable material in this device.

Asbestos and CFC have not been used in the production of the appliance.

The oil in the compressor does not contain PCB.

• THIS APPLIANCE MUST ALWAYS HAVE AN EARTH CONNECTION.
• AT REPAIR AND CLEANING ALWAYS UNPLUG THE APPLIANCE.
• ONLY FOR APPLIANCES WITH REFRIGERANT R290/R600a.

This appliance contains a flammable refrigerant, so ensure good ventilation around the appliance.

Do not use mechanical devices when defrosting, to avoid leakage of the cooling system.

Do not use electrical appliances inside the refrigerator compartment.

Any repair of the appliance should be carried out by a qualified technician (EN 60335-2-89: 2010).

Kids safety

WARNING: This device can be used by children aged 8 and above and individuals with impaired physical, sensory ability or lack of experience and knowledge if they have received supervision or instruction about using the device in a safe way and understand the risks involved.

WARNING: Children must not play with the device.

WARNING: Cleaning and maintenance must not be performed by children without supervision.

WARNING: Should the device require temporary storage,

make sure not to store it near playing children and take care that the door cannot be closed completely.

This will minimize the risk that a child gets trapped inside.

Installation precautions

The appliances mentioned in this document are intended for preservation and cooling of beverages in bottles. They may not be used for purposes other than intended, as this may adversely affect the items that are located inside.

Please read the instructions carefully before using.

Read the manual in order to obtain full benefit from the appliance.

• It is the user's responsibility to utilize the appliance according to the instructions.
• Contact the dealer immediately in case of any malfunction.
• The appliance is for indoor use only. Using it in a place where it is exposed to moisture and rain can cause electrical leakage and electric shock.
• The appliance should be placed in a dry and well-ventilated room.
• Keep away from all sources of heat. The cooling effect is reduced if the unit is placed near hobs and ovens, and if exposed to direct sunlight.
• The appliance should not be placed near a ventilation system.
• Installation should only be done by the dealer or an expert. Attempting to install the device yourself may cause water leakage, refrigerant leakage, or electric shock.
• When disconnecting the power cord plug from the outlet, hold the plug main part close to the outlet.

Pulling the cord could cause wire breakage, possible overheating, and fire.

Disconnect the power cord plug from the wall before moving the unit, and make sure that the power cord is not damaged during transport. A damaged power cord can result in electrical shock and/or fire.

The cable/power cord must not be damaged, bent too much, strained, twisted, or bound together.

If it is unavoidable that the installation is in a local environment, you need to also install an electric circuit breaker. If an electrical leakage circuit breaker is not installed, electrical shock could result.

If heavy objects are placed on the cord, or if it is placed in a location with too little space, it can also be damaged, which may result in electric shock or fire.

WARNING: If the power supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid danger.

Sparks from electrical contacts may result in explosion or fire.

Install the unit in a place where the floor can support the unit's load. If the floor is not sturdy and installation is done incorrectly, the device may fall, and shelves and products may fall out, causing injury.

Leave the disassembly and disposal of the device to qualified experts.

Never attempt to insert fingers, sticks, etc. into the socket, as the fan rotates at high speed inside. Personal injury, electric shock, and incorrect operation may result.

Never place heavy objects or objects containing water on top of the unit. Objects may fall and cause personal injury.

and spilled water can deteriorate the insulation components and result in electrical leakage.

• If you detect a gas leak, do not touch the gas and ensure ventilation by opening windows. Gas leaks can cause explosion, fire, and fire damage.
• Should the device require temporary storage, make sure to store it away from playing children and take precautions so that the door cannot be closed completely. This will reduce the risk that a child gets trapped inside the unit.
• Never climb onto the unit. The unit could tip over and cause material damage or injury.
• Hold the handle when closing the door. Holding other positions could result in pinched fingers and injury.
• Do not push against or apply excessive force to surfaces, as the glass could break and cause injury.
• Make sure that the unit does not tip over or get moved. A falling unit could cause serious injury. Attach and secure shelves correctly. An improperly secured shelf could fall and cause injury.

This manual is machine translated.

Correct disposal of this product

The symbol on the product or on its packaging indicates that it should not be treated as household waste. Instead, it must be handed over to an appropriate collection point for the recycling of electrical and electronic equipment. By ensuring that this product is disposed of correctly, you will help prevent potential negative consequences for the environment and health. For more detailed information on recycling this product, contact your local authority, your household waste center, or the store where you purchased the product.

purchased the product.

Warnings for disposal

Refrigerant and insulating materials are flammable. When the product is scrapped, keep it away from any source of fire. When the product is to be scrapped, remove the door gasket and shelves. Place the doors and shelves away from the product to prevent a child from being trapped.

Environmental protection

This product does not contain ozone-depleting gases in its refrigerant circuit or in its insulation. The product must not be disposed of together with household waste. The insulating materials contain flammable gases: the product must be disposed of according to the product's regulations, avoiding damage to the cooling unit, especially the heat exchanger.

Packaging materials

Materials with this symbol are made from environmentally friendly materials that can be recycled. By disposing of the packaging correctly in accordance with applicable regulations, you help to protect the environment.

WARNING!

The packaging can be dangerous for children!

Plastic parts are marked with the international standard abbreviations:

PE - polyethylene, e.g. the wrapping film

PS - polystyrene, e.g. the upholstery material

POM - polyoxymethylene, e.g. plastic clip

PP - polypropylene, e.g. the salt funnel

ABS - acrylonitrile-butadiene-styrene, e.g. control panel.

Electrical and electronic equipment (EEE) contains materials, components and substances that are dangerous and harmful to human health and the environment when waste electrical and electronic equipment (WEEE) is not disposed of properly.

Products marked with this symbol are electrical and electronic equipment. The crossed-out dustbin symbolizes that waste from electrical and electronic equipment must not be disposed of together with unsorted household waste, but must be collected separately.

To this end, all municipalities have established collection schemes where electrical and electronic equipment can be handed in free of charge at recycling stations or other collection points, or collected directly from households. Further information must be obtained from the municipality's technical administration.

WARNING!

During use, service and disposal of the product, pay attention to the left side, which are usually located on the back of the pre-compressor and are yellow or orange in color. It is the warning hazard. There are flammable materials in the refrigerant piping and

Please keep far away from fire sources during use, service, and

Transport instructions

The product may only be transported upright. The delivered packaging must be used during transport.

If the product was laid down during transport, it must not be run for the following period to allow the system to settle after the product has been returned to the correct position.

Failure to follow the above instructions may result in damage to the product. The manufacturer will not be held responsible if these instructions are ignored. The product must be protected from moisture and other atmospheric influences.

IMPORTANT: Care must be taken when cleaning or lifting the product to avoid touching the capacitor's metal wires at the back of the product, as you may injure your fingers and damage the product.

IMPORTANT: This appliance is not intended to be stacked with other appliances. Do not attempt to sit or stand on top of your device, as it is not intended for such use. You may damage the product.

IMPORTANT: Make sure that the power cable is not stuck under the product during transporting or moving the product, to avoid the power cable being cut, broken, or damaged. When placing your appliance, be careful not to damage your floor, pipes, or wall coverings. Do not move the product by pulling the lid or handle. Do not allow children to play with or tamper with the settings. Our company declines any responsibility if the instructions are not followed.

Before use

Before using the product, you must do the following:

• Remove the shipping package, tape, and duct tape, and leave the doors open for a while.
• If side walls, doors, accessories, and other things are covered with protective foil, this must be removed.
• Thoroughly examine the product for any transport damage after unpacking. In the event of complaints, you must contact the retailer where you purchased the product.
• In case the cabinet has been lying down during transport, leave it standing up for 2 hours before switching it on.
• The unit is cleaned before shipping at the factory. We recommend you clean the cabinet inside an extra time before use.
• Insert the plug into the socket.
• Let the unit run for approximately 1 hour to cool down the cabinet before placing items in the product.

WAIT FOR 5 MINUTES OR MORE BEFORE RESTARTING:

Restarting the device immediately after it has been turned off can cause fuses to jump and activate the circuit breaker, the compressor may be overloaded, and/or other damages may occur.

Installing and adjusting the shelves

The shelves can be adjusted in height. Arrange the shelves according to the dimensions of the goods to be placed in the product. Do not place items heavier than each shelf can handle. Please see product specifications. The shelf could fall, possibly causing injury.

Lighting (LED)
	Lamp type: 1 Horizontal LEDEnergy Efficiency Class (Light): n/aThe light source in this product can only be replaced by a professional.

Correct connection to the earth connection

When you as a consumer connect a product to the electrical installation, you must comply with the applicable legislation of your country. Observe the following safety instructions when installing the product.

WARNING - Electrical Shock Hazard!

• Improper installations are dangerous and can cause personal injury. Follow the user manual and installation instructions when setting up and connecting the device.
• The device may only be connected and used in accordance with the information plate.
• The device may only be connected to an AC mains via a properly installed socket.
• Ground spikes and the ground connection that protects the house's electrical installation must be installed according to regulations. Using the product without an earth connection is dangerous. Always use the cord supplied with the device.
• The cable must never come into contact with heat sources or hot product parts.
• The cord must not be exposed to sharp points or edges. Damaged insulation is dangerous, as ingress of moisture can cause electric shock.
• Never supply the device via an external contact device, e.g. time clock or remote control.
• During installation and use of the device, ensure that the cord is not pinched or damaged in any other way.
• When the device is installed, the mains plug of the cable must be freely accessible. If possible, a switch device must be installed in the fixed electrical installation that complies with applicable installation regulations.

Installation in Denmark

If an HFI relay is used, it must be marked with this symbol.

In Denmark, the device is only approved for use in connection with a type E socket.

If only a type K socket is available at the point of connection, the device must be connected via a suitable adapter. In this way, the device is properly grounded.

This adapter can be purchased from specialist dealers.

Installation outside Denmark

If you live outside Denmark, you must at all times comply with your country's regulations.

Maintenance and cleaning

WARNING

To avoid the risk of electric shock or personal injury from the rotating circulation, unplug the power cord before cleaning.

Never spray water directly on the product or wash with water, as this may cause a short circuit or electrical leakage.

WARNING: Do not use electrical products inside the product storage compartment unless they are of the type recommended by the manufacturer.

Exterior and interior

Wipe with a soft, dry cloth.

If the inside is very dirty, use a cleaning product approved for the purpose, the

WARNING: Do not spray water directly on the product and do not wash with short circuit and electric shock. Clean the product regularly to maintain it clean. powder, soap powder, benzene, oil or hot water as these will damage the paint components.

How to clean the capacitor

(This section is for all products with a visible condenser)

It is important to clean the condenser coil regularly every 2-3 months.

Heavy accumulation of dust on the condenser can lead to reduced cooling efficiency, increased energy consumption, and possible compressor damage.

Follow these steps to clean the condenser:

1. Turn off the power and pull out the plug. 2. Remove the front panel to get access to the condenser. 3. Use a vacuum cleaner or a soft brush in a vertical movement to clean the

Check after cleaning

To guarantee safety, the following points must be checked and carried out after

• Is the plug seated properly in the appropriate socket power outlet?
• Confirm that the connector is not abnormal hot.
• Check the cord for cracks and damage.
• If the slightest irregularity is observed, contact the dealer where you purchased the device, or our customer service.

Instructions for Storing Goods

This product has a cold air circulation system. If the cold air circulation is not adequate, the product will not refrigerate properly.

Pay attention to the following points:

• Do not let items obstruct the cold air inlet and suction outlet.
• Place items so that they do not protrude from the shelves; the gap between the door and shelves is used for cold air circulation.
• Place items evenly on all shelves.
• Do not place goods on the bottom; please put goods on the shelf.

Installation

Ventilation Condition

The position you select for the product installation should be well-ventilated and not located near a heat source or similar, and avoid direct sunlight, thus guaranteeing effect while saving energy consumption. Do not locate the product in a damp place to prevent rusting and leaking electricity.

Level Floor

Place the refrigerator on a solid and flat ground (floor) to keep it stable.

Heat Dissipation Area

When in operation, the product emits heat to the surroundings. Therefore, it is necessary to have sufficient ventilation so that the product can get rid of excess heat.

The more air that circulates around the product in the cabinet, the better it can.

This product is not intended to be used as a built-in product.

Description of the product

A Fan

B Shelf

C Thermostat

D Light switch

Due to technological innovations, the product descriptions in this manual may not be consistent with your product. Detailed information is in accordance with the final product.

Control panel functions

The settings 0 - 5 regulate the internal temperature of the refrigerator.

Setting 0 (OFF) = not operating (Please press the knob to get the "0" position).

Setting 1 (MIN) = lowest setting (warmest internal temperature)

Setting 5 (MAX) = highest setting (coldest internal temperature)

Reversing the door swing

It is not possible to change the doors opening direction.

Normal operating sounds

All products have different "operating sounds," which can sometimes seem annoying but are completely normal functional sounds. They are generally quiet and regular. Here are some of the sounds you can expect to hear that typically do not indicate a problem:

Humming/Buzzing

This is the sound of the compressor working. It is a low, constant sound that the compressor runs to cool down.

Hissing / bubbling

The sound of refrigerant moving through the pipes. It could also be the sound where ice melts and drips onto the heating elements.

Clicking

The sound of the thermostat turning the compressor on and off. This happens normally.

Gurgling

This could be the refrigerant circulating through the system. It can also be the water flowing through the drain pipe during the defrost cycle.

Popping/Cracking

This is usually due to materials expanding and contracting due to temperature changes, common during the de-icing cycle.

Fan sounds

A soft hissing or blowing sound from the fans that circulate the air inside the appliance.

Noise

If you find that the sounds are louder than usual, this can be due to several causes, most of which you can resolve yourself without a visit from a service technician.

The product is not stable

If the product is tilted, it can affect the circulation of refrigerant. Adjust it by placing something underneath.

The door does not close tightly

If the door of the product does not close tightly, the compressor has to work harder to keep the temperature down. Make sure to close the door properly or get a service technician to check the sealing strip.

The product is too close to a wall

The compressor emits small vibrations. If the product is too close to the wall, these vibrations can increase. Fix it by moving the product further away from the wall.

When should you be concerned?

Loud, sudden noises; If you hear loud banging or metallic noises, it may indicate loose or broken parts. Continuous noise; If the product makes constant noise without pause, it is a sign that something is not working properly. Irregular sounds; Irregular clicking, buzzing noises may indicate that something is loose or not working properly.

Troubleshooting

This will help you solve some of the most common problems yourself.

If you cannot solve the problems yourself, call for help from professional technicians.

If the device shows operational problems, you must check the following before contacting an authorized service company:

The device is not working:

• Broken electrical contact • Poor power connection • Thermostat setting on/off:
• Check electrical connections
• Check the power connection and the socket
• Change the thermostat setting to a higher level

Does not reach the desired temperature:

• The device is exposed to direct sunlight • The thermostat is not adjusted correctly • Blocked capacitor or grates • The door is not closed properly • The goods are poorly distributed or there is excessive product load • The device is placed in a room that is too cold

For models with electronic controller:

• Move the product to a colder location
• Adjust the thermostat setting to a higher level
• Clean the grates of any dirt
• Check the product's levelling and the door's sealing in the door gasket
• Redistribute the product load
• Unplug the device from the socket. If the error persists, contact an authorized service center.

Water on the floor:

• The device is not mounted in level • Friction with other objects • The drain hose does not hit the drain tray - Check that the product is level on the surface by following the installation instructions - Move the device and avoid contact with other objects - Move the drain hose so that it hits the drain tray

Sounds of the product:

• The device is not mounted level.
• Friction with other objects / Move the device and avoid contact with other objects.
• Level the product following the installation instructions.
• Move the drain hose so that it hits the drain tray.

Information when contacting service.

You are welcome to contact our after-sale service department if you have questions about our products that you cannot resolve yourself or if you need repair.

Often problems can be remedied by using the section on "Troubleshooting." Contact our service department if this is not the case. We will find the best solution and try to avoid unnecessary service calls.

Due to safety reasons, only trained specialist personnel may carry out repairs. The right to complain about the product expires if repairs or changes are made by persons not given authorization or if non-original spare parts are used.

We offer the purchase of original spare parts in accordance with the relevant regulations for environmentally friendly design. See the appendix for the minimum period during which spare parts are available to repair the product.

Information about the complaint period and conditions can be found on our website, from our service department, or from your dealer.

Contact information can be found on our website www.scandomestic.dk or in the documentation.

We recommend that you have the product's model number and serial number ready when contacting the after-sales service department.

Both parts can be found on the product's type plate, which is inside the product. On some products it may be necessary to remove the vegetable drawer or other equipment.

Write down the information before contacting service.

Technical data

Keep the energy label together with the user manual and other documents for future reference. Further technical information about climate class, refrigerant, and volume can be found on the rating plate.

More information about your product can be found at www.scandomestic.dk or by scanning the QR code in the appendix. By scanning the QR code with your smartphone, you will access the European product register for energy labels. Here you will find more technical data.

Energy calculations and tests.

The product is energy tested as free standing.

It may occur or can be expected that the energy consumption will be higher if the product is installed in a cabinet element and thus has lower ventilation.

EU declaration of conformity

Name and address of the manufacturer or his authorised representative:

Helkama

This declaration of conformity is issued under the sole responsibility of the manufacturer (or installer):

Helkama

References to the relevant harmonised standards used or references to the other technical specifications in relation to which conformity is declared:

EN ISO 17050-1: 2004

Additional Information

Object of the declaration

(identification of product allowing traceability. It may include a colour image of sufficient clarity to enable the identification of the product)

Model number(unique identification of the product):	HJA45B-GDBL
Type	Display Cooler
Brand	Helkama
Outside colour	Black

The object of the declaration described above is in conformity with the relevant Union harmonisation legislation:

ISO 9001, ISO 14001, REACH 1907/2006, RoHS 2011/65/EU, 2015/863, 2011/65/EU, 2014/35/EU, EN 60335-2-89:2010+ A1:2016+A2:2017 EN 60335-1:2012+A11:2014+A13:2017, EN 62233:2008, 2019/2024, 2009/125/EC, 2019/2018, 2017/1369, EN 16902, EN 16902v1.0, 2006/42/EC, IEC 60335-2-89, AMD1:2012, AMD2:2015 with IEC60335-1:2010, AMD1:2013, AMD2:2016, AS/NZS 60335.2.89:2010 + A1:2013+A2:2016, AS/NZS 60335.1:2011+A1:2012+A2:2014+A3:2015+A4:2017, EN60335-2-89:2010+A1:2016, EN60335-1:2012+A11:2014+A13:2017, EN62233:2008, IEC/EN 62031, IEC/EN 62471-1, IEC TR 62778, EN 16902-2016, EN 62321-1:2013, EN 62321-2:2014, EN 62321-3-1:2014, EN 62321-8:2017, MD 2006/42/EC with amendment 2009/127/EC

Information regarding after sales

Access to professional repair, such as websites, addresses, contact information:

Model number: HJA45B-GDBL

Address	Helkama Kodinkoneet Oy Veneetekijäntie 1200210-Finland	QR-code
Contact number	358400290400
Homepage	www.helkamakodinkoneet.fi
Relevant information for ordering spare parts, directly or through other channels provided by the manufacturer, importer or authorised representative;			www.helkamakodinkoneet.fi
The minimum period during which spare parts, necessary for the repair of the appliance, are available; (years)			8
Instruction on how to find the model information in the product database, as defined in Regulation (EU) 2019/2019 by means of a weblink that links to the model information as stored in the product database or a link to the product database and information on how to find the model identifier on the product.)			www.helkamakodinkoneet.fi
Minimum duration of the guarantee offered by the supplier (months)			12

Note: The address or contact phone number of the service site is subject to change without prior notice. Please confirm whether the service station is a directly affiliated one of our company when requiring services.

CE declaration of conformity

This appliance has been manufactured to the strictest standards and complies with all

applicable legislations, Low Voltage Directive (LVD) and Electromagnetic Compatibility (EMC).

Not UKCA approved

This appliance is NOT manufactured after the UKCA standards, but complies with EU standards.

Product information sheet

COMMISSION DELEGATED REGULATION (EU) 2019/2018

Model identifier:	HJA45B-GDBL
Supplier's name or trademark:	Helkama
Use:	Display and sale
Type of refrigerating appliance with a direct sales function:
Cabinet family code, according to the harmonised standards or other reliable, accurate and reproducible methods in accordance with Annex IV.

General product parameters:

1. Beverage coolers*
Total volume (dm3 or L)		Ambient conditions for which the appliance is suitable
		Warmest Temperature (C)	Relative humidity (%)

1. Ice-cream freezers with (transparent lid/non-transparent lid)*

Net volume, L	45	Ambient conditions for which the appliance is suitable
		Temperature Range (°C)		Relative humidity (%)
		Minimum	maximum	minimum	maximum

1. Gelato-scooping cabinet

Total Display Area (m2)

Temperature class

1. [Integral/Remote] [horizontal/vertical (other than semi-vertical)/semi-vertical/combined] supermarket cabinet, roll-in*: [yes/no]:

Total Display Area (m2)

Temperature class

Type of refrigerating appliance

Annual energy consumption	621	Recommended temperature(s) for optimised food storage (°C)
EEI	17,3	Energy efficiency class	B

Light source parameters:

Type of light source	LED
Energy efficiency class (for the light source)	n/a
Minimum duration of the guarantee offered by the supplier, (month)

Additional information

Weblink to the supplier's website, where the information in point 3 of Annex II of Commission Regulation (EU) 2019/2024 is found: www.scandomestic.dk

*(Beverage coolers: fill in point 1, ice-cream freezers: fill in point 2, Gelato-scooping cabinet: fill in point 3, supermarket cabinet: fill in point 4, refrigerated vending machines: fill in point 5. If the refrigerating appliance with a direct sales function contains compartments working at different temperatures, or a compartment that can be set to different temperatures, the lines shall be repeated for each compartment or temperature setting):