LXnC - Dishwasher Hobart - Free user manual and instructions
Find the device manual for free LXnC Hobart in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Commercial Undercounter Dishwasher |
| Model | LXnC |
| Brand | Hobart |
| Dimensions (W x D x H) | 24 x 25 x 33 inches |
| Weight | 150 lbs |
| Voltage | 208-240 V, 60 Hz |
| Phase | 1-Phase |
| Amperage | 20 A |
| Water Connection | 3/4" NPT hot water supply |
| Drain Connection | 2" NPT gravity drain |
| Cycle Time | 90 seconds (wash and rinse) |
| Wash Temperature | 140°F (60°C) |
| Rinse Temperature | 180°F (82°C) |
| Construction Material | Stainless steel interior and exterior |
| Control Type | Electronic with digital display |
| Safety Features | Door interlock, high-limit thermostat, drain overflow protection |
| Cleaning System | Upper and lower rotating wash arms |
| Rinse Aid Dispenser | Built-in automatic dispenser |
| Detergent Dispenser | Integrated with signal light |
| Filter System | Removable stainless steel mesh filter |
| Door Type | Hinged lift door with counterbalance |
Frequently Asked Questions - LXnC Hobart
How do I install the Hobart LXnC dishwasher?
Ensure a dedicated electrical supply (208-240V, 20A) and a hot water line (140°F minimum) with a shut-off valve. Connect the drain to a 2-inch standpipe. Level the unit using the adjustable feet. Refer to the installation manual for detailed steps.
What should I do if the dishwasher doesn't start?
Check that the door is fully closed and the interlock switch is engaged. Verify power supply and circuit breaker. Ensure the water supply is on. If the problem persists, inspect the control board fuse.
How often should I clean the filter?
Clean the stainless steel filter daily to prevent clogs. Remove it by turning counterclockwise and rinse under running water. Inspect for damage weekly and replace if worn.
What type of detergent should I use?
Use a commercial low-foaming detergent specifically for dishwashers. Avoid household detergents as they create excessive suds. Follow the dosage recommended in the manual.
Why is the dishwasher not drying dishes?
Ensure the rinse temperature reaches 180°F. Check that rinse aid is dispensed properly. Verify the booster heater is functioning. Clean the vent opening if blocked.
How do I adjust the cycle time?
Cycle time is preset at 90 seconds. To adjust, access the programming mode by pressing and holding the 'Start' button for 5 seconds. Use the arrow keys to modify wash and rinse durations.
What does the 'Service' light indicate?
The Service light indicates a system fault. Common causes: high limit thermostat tripped, door switch failure, or water level sensor issue. Consult the troubleshooting section of the manual.
Can I use the dishwasher with hard water?
Yes, but hard water can cause scale buildup. Install a water softener if hardness exceeds 5 grains per gallon. Use a descaling solution monthly to maintain performance.
How do I change the wash arms?
Turn off power and water. Unscrew the center hub nut on each wash arm. Lift off the arm and replace with a new one. Tighten the nut securely. Run a rinse cycle to test.
What is the warranty coverage?
Hobart offers a 1-year parts and labor warranty from installation date. The stainless steel tank has a 15-year warranty against perforation. Register your unit online to activate.
User questions about LXnC Hobart
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Dishwasher in PDF format for free! Find your manual LXnC - Hobart and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. LXnC by Hobart.
USER MANUAL LXnC Hobart
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Hobart
Model : LXnC
Category : Dishwasher