N286-10G-SR-J - Network card / adapter Tripp Lite - Free user manual and instructions
Find the device manual for free N286-10G-SR-J Tripp Lite in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | 10 Gigabit SFP+ Transceiver Module |
| Connectivity | LC Duplex Connector |
| Data Rate | 10 Gbps |
| Maximum Distance | 300 m over multimode fiber (OM3) |
| Wavelength | 850 nm |
| Standard | IEEE 802.3ae |
| Dimensions (L x W x H) | 13.4 x 8.5 x 56.5 mm |
| Weight | Approximately 30 g |
| Power Supply | 3.3 V (powered by host port) |
| Operating Temperature | 0°C to 70°C |
| Maintenance and Cleaning | Clean optical connectors with a residue-free cleaning kit |
| Safety | Avoid electrostatic discharge (ESD); handle by the edges |
| Spare Parts and Repairability | Non-repairable module, no spare parts available |
| Warranty | Tripp Lite Limited Warranty |
| General Information | Brand: Tripp Lite; Model: N286-10G-SR-J |
Frequently Asked Questions - N286-10G-SR-J Tripp Lite
What type of fiber does this SFP+ module support?
This N286-10G-SR-J module is designed for multimode fiber (MMF) with a duplex LC connector. It operates on OM3 or OM4 fiber for distances up to 300 meters.
Is this module compatible with any 10 Gigabit switch?
It complies with IEEE 802.3ae standard and SFP+ form factor. It is compatible with most 10 Gigabit Ethernet switches and network cards that support SFP+ modules. Check compatibility with your equipment manufacturer.
What is the difference between this SR module and an LR module?
The SR (Short Range) module uses a wavelength of 850 nm for short distances (up to 300 m on multimode fiber). The LR (Long Range) module uses 1310 nm and can reach 10 km on single-mode fiber.
How to install the SFP+ module?
1. Turn off the equipment or ensure the port is disabled. 2. Insert the module into the SFP+ port, correctly orienting the tab. 3. Gently push until it clicks into place. 4. Connect the fiber cable to the LC connector.
Is the module hot to the touch during operation?
It is normal for the module to warm up slightly. The recommended operating temperature is 0°C to 70°C. Ensure adequate ventilation around the module.
What to do if the module is not recognized by the equipment?
Check that the module is fully inserted and the latch is in place. Ensure the SFP+ port is enabled. Try restarting the equipment. If the problem persists, test with another port or another module.
How to clean optical connectors?
Use an optical fiber cleaning kit with lint-free wipes or a cassette cleaner. Gently wipe the connector end face before each connection to avoid signal loss.
Is this module hot-pluggable?
Yes, SFP+ modules are designed to be hot-swapped without powering off the equipment. However, it is recommended to logically disable the port before replacement to avoid disruption.
What is the typical optical output power?
The typical output power is between -7.3 and -1.0 dBm. The receive sensitivity is -11.1 dBm maximum. These values may vary depending on conditions.
Does the module have a warranty?
Yes, Tripp Lite offers a limited warranty. Check the official website for details. This module is designed for a long service life, but it is not repairable; if it fails, it must be replaced.
User questions about N286-10G-SR-J Tripp Lite
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Network card / adapter in PDF format for free! Find your manual N286-10G-SR-J - Tripp Lite and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. N286-10G-SR-J by Tripp Lite.
USER MANUAL N286-10G-SR-J Tripp Lite
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Tripp Lite
Model : N286-10G-SR-J
Category : Network card / adapter