CS60.4 - Receiver JBL - Free user manual and instructions
Find the device manual for free CS60.4 JBL in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Car Audio Amplifier |
| Model | CS60.4 |
| Number of Channels | 4 |
| RMS Power per Channel | 60 Watts @ 4 ohms, 90 Watts @ 2 ohms |
| Total RMS Power | 240 Watts (4 x 60W) |
| Peak Power per Channel | 150 Watts |
| Frequency Response | 20 Hz - 20 kHz |
| Input Sensitivity | 200 mV - 6 V |
| Signal-to-Noise Ratio | > 100 dB |
| Total Harmonic Distortion (THD) | < 0.05% |
| Low-Pass Crossover | 40 Hz - 400 Hz |
| High-Pass Crossover | 40 Hz - 400 Hz |
| Bass Boost | 0 - 12 dB @ 45 Hz |
| Inputs | 4 x RCA, high-level (speaker) inputs |
| Outputs | 4 x speaker terminals |
| Power Supply Voltage | 12 V DC (11-16 V) |
| Dimensions (L x W x H) | 10.2 x 6.5 x 2.0 inches (259 x 165 x 51 mm) |
| Weight | 4.5 lbs (2.04 kg) |
| Protection Features | Thermal, overload, short circuit, reverse polarity |
| Recommended Fuse | 30A (AGU type) |
| Certifications | CE, RoHS |
Frequently Asked Questions - CS60.4 JBL
What is the RMS power output of the JBL CS60.4?
The JBL CS60.4 delivers 60 watts RMS per channel into 4 ohms and 90 watts RMS per channel into 2 ohms.
Can I bridge channels on the CS60.4?
Yes, you can bridge channels 1/2 and 3/4 to obtain 180 watts RMS into a 4-ohm load.
What type of power supply does the CS60.4 require?
It requires a 12V DC negative ground electrical system, typical in cars. The amplifier can handle a voltage range of 11-16 volts.
Does the CS60.4 have a built-in crossover?
Yes, it features a fully adjustable low-pass and high-pass crossover (40 Hz - 400 Hz) and a variable bass boost (0-12 dB at 45 Hz).
How do I set the gain on the JBL CS60.4?
Start with the gain fully down, play a clean test tone at 75% volume, and slowly increase the gain until you hear distortion, then back it off slightly. Use a multimeter or oscilloscope for precise setting.
What are the dimensions of the CS60.4?
The dimensions are approximately 10.2 x 6.5 x 2.0 inches (259 x 165 x 51 mm).
Can the CS60.4 be used with an OEM factory stereo?
Yes, it has high-level (speaker) inputs that allow direct connection to factory head units without needing a line output converter.
What fuse rating should I use for the CS60.4?
JBL recommends a 30A AGU fuse on the power wire near the battery.
Does the CS60.4 have protection against overheating?
Yes, the amplifier includes thermal protection that shuts down the amp if it gets too hot, preventing damage.
How many channels does the CS60.4 have and what configurations are possible?
It is a 4-channel amplifier that can power four speakers, two speakers bridged, or a combination of speakers and a subwoofer using channels 3/4 bridged.
User questions about CS60.4 JBL
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Receiver in PDF format for free! Find your manual CS60.4 - JBL and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. CS60.4 by JBL.
USER MANUAL CS60.4 JBL
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : JBL
Model : CS60.4
Category : Receiver