AquaTrio Cordless XW9384 - Vacuum Cleaner PHILIPS - Free user manual and instructions

Product type	Cordless stick vacuum cleaner
Brand	Philips
Model	AquaTrio Cordless XW9384
Power supply	Rechargeable lithium-ion battery
Battery voltage	25.2 V
Runtime	Up to 40 minutes in standard mode
Charging time	About 4 hours
Clean water tank capacity	500 ml
Dirty water tank capacity	400 ml
Dust bin capacity	600 ml
Weight	4.8 kg
Dimensions (L x W x H)	300 x 250 x 1150 mm
Noise level	78 dB(A)
Main functions	Simultaneous vacuuming and washing
Filter type	Washable filter
Battery indicator	LED on handle
Included accessories	Crevice tool, furniture brush, charging station
Maintenance	Filter and roller washable with clean water
Safety	Automatic shut-off in case of overheating
Warranty	2 years
Country of origin	China

Frequently Asked Questions - AquaTrio Cordless XW9384 PHILIPS

How to start the AquaTrio Cordless XW9384?

Press the power button located on the handle. The LED indicator lights up if the battery is sufficiently charged.

How to clean the vacuum filter?

Remove the filter and rinse it with clean water. Let it dry completely before putting it back. Do not use detergent.

What to do if the runtime decreases?

Check that the filter is clean and the roller is not blocked. If the problem persists, the battery may need to be recalibrated or replaced.

Can I use the device on thick carpets?

Yes, but washing performance is optimized on hard floors. On carpets, use only vacuuming without activating washing.

How to empty the dirty water tank?

Unclip the dirty water tank, empty it into the sink and rinse it. Put it back ensuring it is properly locked.

What type of cleaning product to use for washing?

Use only clean water. Adding detergent can clog the system and void the warranty.

How to recharge the vacuum cleaner?

Place the device on the provided charging dock. Full charging time is about 4 hours. The indicator shows the charging status.

What to do if the vacuum loses suction power?

Check that the dust bin is not full, the filter is clean, and the brush roller is not tangled with hair or fibers.

How to store the device?

Use the charging station for vertical storage. You can also lay it flat after removing the water tank.

Where to find spare parts?

Contact Philips customer service or check their official website. Available parts include the brush roller, filter, and battery.

USER MANUAL AquaTrio Cordless XW9384 PHILIPS

English 6

Čeština 52

Dansk 97

Deutsch 142

Eesti 189

Français 234

Hrvatski 280

Italiano 325

Latviešu 371

Lietuviškai 415

Magyar 460

Nederlands 505

Norsk 551

Polski 595

Română 641

Slovenščina 686

Slovensky 730

Srpski 775

Suomi 820

Svenska 865

Türkçe 910

Български 955

Contents

Introduction 6

General description 6

Before first use 7

Charging 10

Vacuuming and mopping hard floors 11

Vacuuming soft and hard floors 16

Cleaning the Vacuum & Mop set-up 21

Cleaning the Vacuum only set-up 30

Display icons and their meaning 39

Replacement 42

Troubleshooting 42

Using the Vacuum only set-up ____ 48

Introduction

Thanks for buying this Philips product! To fully benefit from the support that Philips offers, register your product at www.philips.com/myvacuum9000s.

General description

1 Dust bucket release button
2 Display
3 Cleaning mode button
4 Middle button (AUTOCLEAN)
5 On/off button
6 Battery
7 3-in-1 handheld
8 Dust bucket
9 Wall mount
10 Tube
11 LED nozzle
12 Mini Turbo brush
13 Long crevice tool
14 Adapter
15 Power plug
16 Extra charger (XW9385 only)
17 After-Clean & Storage station
18 Appliance holder
19 After-Clean tray
20 Baseplate
21 Wet module
22 Dirty water tank
23 Clean water tank
24 AquaSpin nozzle
25 Microfiber brushes
26 Philips Floor Cleaner XV1792
27 Cleaning brush

Before first use

Assembling the After-Clean & Storage station

In order to use the AUTOCLEAN function or store and charge the appliance on the After-Clean & Storage station, you need to first assemble the station by clicking the appliance holder into the baseplate.

Tip: It is possible to slide the holder for Vacuum only set-up and put it back upside down if you want to place the Vacuum only set-up on the other side of the After-Clean & Storage station.

i Note: Make sure that the After-Clean tray is placed in the baseplate and that the temperature in the room where the appliance is stored, charged and cleaned is between 5 °C and 35 °C.

Tip: You can hang the cleaning brush on the hook of the appliance holder.

Installing the wall mount

If you want to store and charge the Vacuum only set-up on the wall mount, fasten the wall mount to the wall with the screws supplied. Make sure the wall mount is 140 - 150 cm above the floor.

i Note: It is not possible to store the Vacuum & Mop set-up on the wall-mount. It is only possible to store the Vacuum only set-up on the wall mount.

i Note: Make sure that the temperature in the room where the appliance is stored or charged is between 5 °C and 35 °C.

Caution: Be careful when you drill holes in the wall to fasten the wall mount, to avoid the risk of electric shock.

Assembling the Vacuum & Mop set-up

1 To assemble the Vacuum & Mop set-up, insert the battery and attach the 3-in-1 handheld to the wet module ('click').

2 Attach the wet module to the AquaSpin nozzle ('click').

3 To store the Vacuum & Mop set-up, you can place it in the After-Clean & Storage station.

i Note: It is not possible to store the Vacuum & Mop set-up on the wall-mount. It is only possible to store the Vacuum only set-up on the wall mount.

Assembling the Vacuum only set-up

1 To assemble the Vacuum only set-up, attach the 3-in-1 handheld to the dust bucket ('click').

2 Attach the dust bucket to the tube ('click').

3 Insert the tube into the LED nozzle.

4 To store the Vacuum only set-up, place it in the After-Clean & Storage station by first placing the LED nozzle onto the long side of the baseplate and then pressing the tube into the holder.

Tip: It is possible to slide the holder for the Vacuum only set-up and put it back upside down if you want to place the Vacuum only set-up on the other side of the After-Clean & Storage station.

Charging

The appliance is equipped with a 25 V Li-Ion battery. Charging takes 4 hours.

1 To charge the appliance, insert the power plug into the socket on the back of the appliance. Then insert the adapter into the wall socket.
2 A value between 0% and 90% flashes on the screen to indicate that the appliance is charging.

3 When the appliance is fully charged, the value 100% lights up on the screen. After a few minutes, the display will switch off.

Warning: Store and charge the appliance at a temperature above 5 °C and below 35 °C.

Tip: You can charge the appliance when it is attached to the wall mount.

Tip: You can charge the appliance in the After-Clean & Storage station.

Tip: You can charge the appliance separately in a place that suits you best.

Vacuuming and mopping hard floors

Using the Vacuum & Mop set-up

The clean water tank and the dirty water tank are already attached to the appliance upon delivery. With the wet module attached to the AquaSpin nozzle, you can clean hard floors.

i Note: This Vacuum & Mop set-up is suitable for vacuuming and mopping at the same time. It is not necessary to vacuum the floor before mopping. The Vacuum & Mop set-up is suitable for vacuuming and mopping all types of hard floors, except uncoated wooden floors (see 'Usage restrictions').

1 To assemble the Vacuum & Mop set-up, insert the battery and attach the 3-in-1 handheld to the wet module ('click').

2 Attach the wet module to the AquaSpin nozzle ('click').

3 Push the button to unlock the clean water tank and remove the clean water tank.

4 Remove the cap from the clean water tank.

5 Add 10 ml of the XV1792 Philips Floor Cleaner to the clean water tank.

Caution: Philips has only tested this appliance with XV1792 Philips Floor Cleaner. Other detergents may lead to excessive foaming, which reduces performance and may cause the appliance to malfunction. XV1792 Philips Floor Cleaner is available in selected markets. When using any other suitable liquid floor cleaner, add a maximum of 10 ml to the clean water tank.

6 Fill the clean water tank with cold or lukewarm tap water up to the MAX indication.

Caution: The tap water that is poured into the clean water tank must not be warmer than 50°C.

7 Place the cap back on the clean water tank.

8 Place the clean water tank back into the appliance.

9 To switch on the appliance, press the on/off button and wait until the appliance is ready for use.

10 Use the cleaning mode button to choose between three different settings:

• Normal wet mode
• Intense wet mode
• Water absorption mode

By selecting the normal water mode, you can use the appliance for regular wet cleaning. The intense wet mode is for cleaning extra stubborn stains.

If there are wet spots on the floor after cleaning, you can select absorption mode to clean them up. We also recommend using it when lifting the appliance over a threshold, carpet or stairs (see 'Tips and other important information').

If you select water absorption mode, the appliance will stop supplying water and increase suction power for 45 seconds to absorb any water on the floor.

i Note: older models feature normal wet mode and intense wet mode, but not water absorption mode.

Active protection system

• This appliance is equipped with an active protection system. This active protection system has been designed to recognize when a foreign object other than dirt or liquid is picked up from the floor.
• When the system is activated, the appliance switches off and the i3 message appears on the display (see 'Display icons and their meaning'). The active protection system can also be activated when the microfiber brushes are too wet, when you move the appliance over a carpet or a rug, or when you move it over flooring that is not properly affixed.

Tips and other important information

• It is not necessary to vacuum the floor before mopping, as the Vacuum & Mop set-up actively wet-cleans your hard floor to capture all kinds of dirt, including liquids and stains. On carpets and rugs, use the Vacuum only set-up.
• If your hard floors do not need mopping, simply use the vacuum only set-up which features LED lights and PowerCyclone 12 technology for precise and powerful dirt pick-up.
• You can move the appliance just as quickly as a vacuum cleaner. To remove difficult stains, click the cleaning mode button to activate the intense wet mode and move the appliance slowly over the stains.
• The appliance can leave a small puddle of water on the floor if you do not move the appliance while switching it off. You can reduce the size of the puddle by moving the appliance while switching it off. If needed, you can remove the last drops with a cloth.
• It is recommended to activate the water absorption mode when lifting the appliance over a threshold, carpet or stairs during cleaning. This will prevent dirty water from dripping out of the AquaSpin nozzle.
• When moving the appliance, it is recommended to stretch your arm to reduce unnecessary tension on the muscles. In this position, you have the best control over the appliance when cleaning, and it will be the most comfortable.

i Note: When you use the water absorption mode, no more water comes out of the appliance and the suction power increases. After 45 seconds, if you

do not take any action, the appliance automatically switches back to normal wet mode 🔒

Note: older models feature normal wet mode and intense wet mode, but not water absorption mode. For these models, move the appliance while switching it off to reduce the amount of water left on the floor. It is also recommended to leave the appliance on when lifting it over a threshold, carpet or stairs during cleaning. This will prevent dirty water from dripping out of the AquaSpin nozzle.

Usage restrictions

• The Vacuum & Mop set-up is suitable for vacuuming and mopping all types of hard floors, except uncoated wooden floors.
• The Vacuum & Mop set-up is intended for regular cleaning of hard floors. Always follow the cleaning instructions for your hard floor when you use this appliance.
• If you want to add a liquid floor cleaner other than XV1792 Philips Floor Cleaner to the water in the clean water tank, make sure that you use a low-foaming or non-foaming liquid floor cleaner that can be diluted in water like XV1792 Philips Floor Cleaner.
• As the clean water tank has a capacity of 400ml, you only have to add a few drops (max 10ml) of liquid floor cleaner to the water.
• If you use the Vacuum & Mop set-up on linoleum floors, only do so on linoleum floors that are properly affixed to prevent linoleum from being drawn into the AquaSpin nozzle.
• Do not use the Vacuum & Mop set-up to clean carpets.
• If you move/lift the appliance over a carpet or rug when it is switched off, wastewater droplets may end up on your carpet or rug.
• Do not push the appliance over the floor grilles of convector heaters. As the appliance cannot pick up water that comes out of the nozzle when you move it over the grille, water ends up at the bottom of the convector pit.
• While cleaning, do not lift the AquaSpin nozzle from the floor or move the AquaSpin nozzle sideways, and do not make strong turns, as this leaves water traces. Only move forwards and backwards.

i Note: The operating time depends on the power level used during cleaning.

Note: older models only feature normal wet mode and intense wet mode, but not water absorption mode

Vacuuming soft and hard floors

Using the Vacuum only set-up

1 To vacuum soft or hard floors, attach the 3-in-1 handheld to the dust bucket ('click').

Caution: Do not attach the 3-in-1 handheld to the dust bucket without the filter case being inserted in the dust bucket.

2 Attach the dust bucket to the tube ('click').

3 Insert the tube into the LED nozzle.

4 To switch on the appliance, press the on/off button and wait until the appliance is ready for use.

5 Use the buttons on the left and right to choose between the two different power settings.

Tip: The LEDs in the LED nozzle make it easier to see dirt on the floor. The tube and LED nozzle allow you to reach under low furniture without the need to twist the appliance.

Warning: Do not vacuum up water or other liquids.

Caution: Do not look directly into the LEDs of the LED nozzle or point the LEDs at someone's eyes. The LED light is very bright.

Using the tube

You can attach the tube to the handheld and use it without a nozzle to vacuum tight spaces between or behind pieces of furniture with the end of the tube.

Tip: It is also possible to attach the Mini Turbo brush to the tube.

Tip: It is also possible to attach the long crevice tool to the tube.

Using the handheld

Without the nozzle and tube, you can use the handheld to clean small patches of dust and dirt, such as spilled breadcrumbs, or to vacuum staircases and shelves.

Warning: Do not vacuum up water or other liquids.

Using the LED nozzle

You can use the LED nozzle to clean areas, such as the steps of a staircase, to vacuum up dirt in corners or on narrow ledges, or to clean small patches of dirt, such as spilled breadcrumbs.

1 To attach the LED nozzle, insert the tube or the handheld into the nozzle.

2 To detach the LED nozzle, press the release button (1) and pull the tube or handheld out of the nozzle (2).

Warning: Do not vacuum up water or other liquids.

Using the Mini Turbo brush

1 To attach the Mini Turbo brush, insert the tube of the handheld into the Mini Turbo brush.

2 You can use the Mini Turbo brush for standard cleaning, for instance of soft areas such as beds and couches. You can adjust the power setting to suit your cleaning needs.

3 You can use the Mini Turbo brush for extra thorough cleaning, for instance to vacuum up pet hair, or to clean small patches of dirt, such as spilled breadcrumbs. You can adjust the power setting to suit your cleaning needs.

4 To detach the Mini Turbo brush, press the release button (1) and pull the handheld out of the Mini Turbo brush (2).

Warning: Do not vacuum up water or other liquids.

Using the long crevice tool

1 To attach the long crevice tool, insert the tube or handheld into the long crevice tool.

2 You can use the long crevice tool to clean narrow corners or hard-to-reach places. You can adjust the power setting to suit your cleaning needs.

3 To detach the long crevice tool, press the release button (1) and pull the tube or handheld out of the long crevice tool (2).

Warning: Do not vacuum up water or other liquids.

Cleaning the Vacuum & Mop set-up

AUTOCLEAN after every use

To prevent odors and scale deposits, use the AUTOCLEAN function after every use. The AUTOCLEAN mode helps you to clean your full appliance in approximately 4 minutes.

1 Place the Vacuum & Mop set-up in the After-Clean & Storage station.

i Note: If the dirty water level is below the AUTOCLEAN level, it is not necessary to empty the tank before starting the AUTOCLEAN program. You can skip the following steps and move forward to step 6.

2 Push the button to unlock the dirty water tank and remove it.

3 Remove the wet filter from the dirty water tank.

4 Pour the water out of the dirty water tank into the sink.

5 Place the wet filter back on the dirty water tank.

6 Place the empty dirty water tank back into the appliance and take out the clean water tank.

7 Remove the cap from the clean water tank.

8 Pour any remaining detergent liquid from the clean water tank into the sink.

9 Fill the clean water tank with cold or lukewarm tap water at least up to the AUTOCLEAN indication.

Caution: The tap water that is poured into the clean water tank must not be warmer than 50°C.
Caution: Do not use detergent for the AUTOCLEAN as this might lead to excessive foaming.

10 Place the clean water tank back into the appliance.

11 Charge the appliance. Insert the power plug into the socket on the back of the appliance. Then insert the adapter into the wall socket.

12 To start the AUTOCLEAN cycle, press the middle button. If you see a black screen, press the on/off button first to activate the screen.

13 The appliance performs the AUTOCLEAN cycle.

i Note: The Autoclean cycle lasts approx. 4 minutes. For best results, let the appliance run through the AUTOCLEAN cycle completely. You can pause or cancel the AUTOCLEAN cycle at any time.

i Note: If you cancel the AUTOCLEAN program, the appliance will suck up the remaining water in the After-clean tray for about 10 seconds.

14 Push the button to unlock the dirty water tank and remove it.

15 Remove the wet filter from the dirty water tank.

16 Pour the water out of the dirty water tank into the sink.

17 Clean the dirty water tank under the tap.

18 Clean the wet filter under the tap.

19 Let the wet filter of the dirty water tank and its water flow element dry completely before putting it back on the dirty water tank.

20 Place the wet filter back on the dirty water tank.

21 Place the dirty water tank back into the appliance.

22 Turn the microfiber brushes counterclockwise (1) and remove them from the AquaSpin nozzle (2).

Tip: In case a microfiber brush is difficult to remove, you can use the cleaning brush handle to unlock the microfiber brush.

23 To allow the microfiber brushes to dry, place the open ends of the brushes on the designated holders of the After-Clean & Storage station.

i Note: Drying can take approximately 24 hours.

Cleaning the After-Clean tray

If the After-Clean tray gets dirty, you can clean it by following the steps below.

1 Remove the After-Clean tray from the storage station.

2 Rinse the After-Clean tray under the tap and let it dry before placing it back in the Storage station.

3 Make sure to always put the After-Clean tray back in the Storage station. The After-Clean tray is essential to perform the AUTOCLEAN correctly.

Cleaning the AquaSpin nozzle

1 Turn the microfiber brushes counterclockwise (1) and remove them from the AquaSpin nozzle (2).

Tip: In case a microfiber brush is difficult to remove, you can use the cleaning brush handle to unlock the microfiber brush.

2 You can remove entangled hair or threads from the microfiber brushes by sliding down the microfiber brushes with one hand.

Tip: You can also use a pair of scissors to cut hairs and threads that have become entangled around the microfiber brushes.

Removing blockages from the Vacuum & Mop set-up

The Vacuum & Mop set-up may become clogged. You may notice this when more water gets on the floor than usual or when bigger dirt particles are no longer sucked up and fall back on the floor. Below you can find the instructions to remove blockages from different parts of the Vacuum & Mop set-up.

Clearing blockages from the wet module

If there is a blockage in the wet module, first switch off the appliance and remove the AquaSpin nozzle and the 3-in-1 handheld. Then remove the blockage by moving the cleaning brush in the suction channel of the wet module up and down.

Clearing blockages from the AquaSpin nozzle

If there is a blockage in the AquaSpin nozzle, it can be removed by moving the cleaning brush up and down in the suction channel of the AquaSpin nozzle.

Clearing blockages from the wetting strips of the AquaSpin nozzle

After long and frequent use of the appliance, the wetting strips of the AquaSpin nozzle may become clogged at some point. Follow the steps below to clear the blockage of the wetting strips of the AquaSpin nozzle.

1 Remove the wetting strip covers from the AquaSpin nozzle by moving them sideways.

2 Remove the wetting strips from the AquaSpin nozzle by pulling them out sideways.

3 Rinse the wetting strips under the tap.

4 Let the wetting strips dry before placing them back in the AquaSpin nozzle.

Cleaning the Vacuum only set-up

Emptying the dust bucket

Regularly empty the dust bucket and make sure that the dirt never exceeds the 'Max' indication. This prevents accelerated filter clogging.

1 Press the release button (1) to release the 3-in-1 handheld of the dust bucket and then lift the 3-in-1 handheld off the appliance (2).

2 Pull the filter case off the dust bucket.

3 Empty the dust bucket into a waste bin.

4 Put the filter case back onto the dust bucket.

5 Reconnect the 3-in-1 handheld to the dust bucket. Make sure that you connect the rear part first, then connect the front part so it locks into place with a click.

Cleaning the dust bucket

1 To clean the dust bucket and the cyclone, remove the filter case.

2 Empty the dust bucket into a waste bin.
3 Remove and clean the cyclone if necessary (see 'Cleaning the cyclone').

4 If you want, you can use a wet or dry cloth to clean the inside of the dust bucket.

i Note: do not let the electronic connectors get wet. If the electronic connectors do get wet, please allow them to dry before using the device again. Always use the appliance with dry electronic connectors. This prevents the appliance from malfunctioning over time.
Warning: Do not clean the dust bucket in the dishwasher.
Warning: Do not rinse the dust bucket under the tap.

5 Reattach the filter case back in when the dust bucket is dry.

6 Reconnect the 3-in-1 handheld to the dust bucket.

Caution: Do not reconnect the 3-in-1 handheld to the dust bucket without the filter case being inserted in the dust bucket.

Cleaning the cyclone

1 Turn the cyclone clockwise (1) and remove it from the dust bucket (2).
2 Remove hair and dirt that is stuck in and under the cyclone.

3 If desired, you can rinse the cyclone under the tap.

i Note: Always let the cyclone dry completely before placing it back into the dust bucket.

4 Replace the cyclone (1) and turn it counterclockwise (2) to secure it back into the dust bucket.

Caution: Make sure to fully tighten the cyclone when placing it back. Rotate the cyclone until the cyclone cannot rotate any further and is fully secured.

Cleaning the filter

When the filter needs to be cleaned, the filter cleaning icon appears on the screen.

1 Pull the filter case off the dust bucket.

2 Press the release button to release the lid of the filter case and remove the foam filter.

Caution: Make sure that the filter case lid does not get wet during cleaning.

3 Shake the foam filter over a waste bin to remove the layer of dirt on top of the foam filter. Then rinse the foam filter under a tap.

4 Squeeze the foam filter to remove the water.

5 Shake the filter case and lid over a waste bin to remove dust.

6 Clean the filter holder with a damp cloth.

Caution: Do not clean the white material of the filter case lid with a normal vacuum cleaner or a brush. Do not clean the white material of the filter case lid with water or any cleaning agent. It will damage the material. The white material can be tapped over a bin.

7 Let the foam filter dry and make sure that it is completely dry before you put it back into the filter case.

Caution: Make sure that the foam filter is correctly placed in the filter case.

8 Close the filter case.

9 Put the filter case including the foam filter back into the dust bucket.

Caution: Make sure the white material of the filter case lid is facing up.

Caution: Make sure that the filter case including the foam filter are completely dry before you put them back into the dust bucket.

10 Reconnect the 3-in-1 handheld to the dust bucket.

Caution: Do not reconnect the 3-in-1 handheld to the dust bucket without the filter case being inserted in the dust bucket.

i Note: Replace the filter every 6 months to ensure maximum performance. Replacement filters are available under part number XV1791 (see 'Replacement').

Cleaning the motor inlet filter

The 3-in-1 handheld has a filter that may become blocked with dust. This can reduce the suction power over time. To clean the motor inlet filter, follow these steps:

1 Press the release button (1) to release the 3-in-1 handheld of the dust bucket and then lift the 3-in-1 handheld off the appliance (2).

2 Clean the inlet filter with a cloth or with the cleaning brush.

3 Reconnect the 3-in-1 handheld to the dust bucket. Make sure that you connect the rear part first, then connect the front part so it locks into place with a click.

Cleaning the roller brush

1 Pull down the locking lever on the side of the LED nozzle (1) and slide the roller brush out of the LED nozzle (2). You can remove entangled hair or threads from the roller brush by sliding down the roller brush with one hand.

Tip: You can also move one blade of a pair of scissors through the groove on the roller brush to cut hairs and threads that have become entangled around the roller brush.

2 Slide the roller brush back into the LED nozzle (1) and push up the locking lever to lock the roller brush in the LED nozzle ('click').

Cleaning the Mini Turbo brush

1 Unlock the release button on the side of the Mini Turbo brush (1) and lift the roller brush out of the Mini Turbo brush (2).

2 Remove the hairs and dirt entangled around the roller brush.

Tip: You can also move one blade of a pair of scissors through the groove on the roller brush to cut hairs and threads that have become entangled around the roller brush.

3 Press one side of the roller brush back into the Mini Turbo brush (1) and push down the other side of the roller brush to lock the roller brush in the Mini Turbo brush ('click').

Display icons and their meaning

Error code Cause Solution

There is a system error. An E1 error code means that your Philips

AquaTrio 9000 series Vacuum Cleaner has a system error.

To solve this, please try one or both of the following options:

1. Remove the battery from the appliance and then reinsert the battery. Then try to restart the appliance.
2. Disconnect the 3-in-1 handheld from the appliance and press the on/off button Ⓤ on the handheld. If you still see the E1 error on your display, please contact the Consumer Care Center. If you do not see the E1 error and the appliance does still not work, there might be a communication problem with the tube or nozzle. Please contact the Consumer Care Center.

The temperature is too low. Make sure the temperature in the room where the appliance is used, stored, or charged is above 5 °C.

The temperature is too high. Make sure the temperature in the room where the appliance is used, stored, or charged is below 35 °C. Do not expose the device to direct sunlight or high temperatures (near hot stoves, in microwave ovens, or on induction cookers). Batteries may explode if overheated.

Information code Cause Solution

The dirty water tank is full. Empty the dirty water tank.

Information code Cause Solution

	The AquaSpin nozzle is not connected (properly).	Connect the AquaSpin nozzle.
	The AquaSpin nozzle is stuck. This is a safety cut-off if something is stuck in the nozzle (for instance, a power cable or a toy).	Check the brushes, bearings, motor parts, and caps for hair or other obstacles and remove them. If there are no obstacles, switching the appliance off and on might solve the problem.
	The LED nozzle is stuck. This is a safety cut-off if something is stuck in the nozzle (for instance, a power cable or a toy).	Check the roller brush and the rest of the nozzle for hair or other obstacles and remove them (see 'Cleaning the roller brush'). If there are no obstacles, switching the appliance off and on might solve the problem.
	The air inlet openings are blocked.	Check the air inlet openings for blockages and remove them. If this does not solve the problem, check the whole air passage for blockages and remove them. For the Vacuum only set-up, this refers to the nozzle, tube, filter, vortex finder, long crevice tool, and Mini turbo brush. For the Vacuum & Mop set-up, this refers to the nozzle, tube, and the wet filter.
	Unplug for use. Unplug the appliance for use. Otherwise, it will not switch on. Only during AUTOCLEAN is it possible to have the appliance plugged in.

Information code Cause Solution

	The wrong charger is connected.	Only charge the appliance with the adapter supplied. Only use 34V adapter S036-1A340100HE. The corresponding adapter number can be found on the adapter.
Icons Meaning
	AUTOCLEAN
	Reminder to clean the filter (see 'Cleaning the filter')
	Microfiber brush replacement needed
	Filter replacement needed

Replacement

To buy accessories or spare parts, visit www.philips.com/parts-and-accessories or go to your Philips dealer. You can also contact the Philips Consumer Care Center in your country (see the international warranty leaflet for contact details).

Replacement parts and type numbers:

• Replacement filter XV1791
• Philips Floor Cleaner XV1792
• Replacement microfiber brushes XV1793
• Lithium-Ion Battery pack 25.2V XV1797

Replace the filter and the microfiber brushes every 6 months to ensure maximum performance.

i Note: You can dispose of the old filter and the microfiber brushes with the normal household waste.

Troubleshooting

This chapter summarizes the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Center in your country.

Using the Vacuum & Mop set-up

Problem Possible cause Solution

The appliance does not work when I push the on/off button.	The battery is not connected. Connect the battery to the 3-in-1 Handheld.
	The battery is empty. To charge the battery, connect the 3-in-1 Handheld with the charger (see 'Charging').
	You did not take the appliance out of the After-Clean & Storage station.	Take the Vacuum & Mop set-up out of the After-Clean & Storage station before switching on the appliance.
	You pushed the on/off button more than one time.	Wait a few seconds and push the on/off button again one more time.
	You did not connect the 3-in-1 Handheld to the appliance correctly.	Place the lower body of the appliance on the After-Clean & Storage station. Then connect the 3-in-1 Handheld to it.
	The appliance is clogged. Switch	the appliance off and remove the battery or 3-in-1 handheld. Then locate and remove the cause of the blockage (see 'Removing blockages from the Vacuum & Mop set-up'). After that, restart the appliance. If you cannot identify the cause of the blockage, restart the appliance. This might already solve the problem.

Problem Possible cause Solution

	The microfiber brushes are stuck.	Take the microfiber brushes out and place them back (see 'Cleaning the AquaSpin nozzle').Tip: In case a microfiber brush is difficult to remove, you can use the cleaning brush handle to unlock the microfiber brush (see 'Cleaning the AquaSpin nozzle').
The appliance stopped working.	You accidentally touched the on/off button with your hand.	Switch on the appliance by pushing the on/off button.
	The dirty water tank may be full. In this case, there is an information icon shown on the screen (see 'Display icons and their meaning').	Empty the dirty water tank (see 'AUTOCLEAN after every use').
	The appliance is clogged. Switch the appliance off and remove the battery or 3-in-1 handheld. Then locate and remove the cause for the blockage (see 'Removing blockages from the Vacuum & Mop set-up'). After that, restart the appliance. If you do not identify the cause for the blockage, just restart the appliance. This might already solve the problem.
The floor is less wet than usual.	The wetting strips are blocked.	Remove the two microfiber brushes, fill some water into the clean water tank and switch the appliance on. Make small forward and backward movements on the same position for around 15 seconds. You should be able to see four water stripes on the floor. If this is not the case, or if one or more water stripes only consist out of a few droplets, the wetting strips are partially or fully blocked and you can rinse them under the tap (see 'Clearing blockages from the wetting strips of the AquaSpin nozzle'). If that does not help, you can try to carefully open the holes with a needle.
One side of the floor under the nozzle is less wet than the other one.	One of the two wetting strips is blocked.	Remove the two microfiber brushes, fill the clean water tank with some water, and switch the appliance on. Make small forward and backward movements on the same position for around 15 seconds. You should be able to see four water stripes on the floor. If this is not the case, or if one or more water stripes only consist out of a few droplets, the wetting strips are partially or fully blocked and you can rinse them under the tap (see 'Clearing blockages from the

Problem Possible cause Solution

		wetting strips of the AquaSpin nozzle'). If that does not help, you can try to carefully open the holes with a needle.
There is no water on the floor.	The clean water tank is empty.	Refill the clean water tank (see 'Using the Vacuum & Mop set-up').
	The wetting strips are blocked.	Remove the two microfiber brushes, fill the clean water tank with some water, and switch the appliance on. Make small forward and backward movements on the same position for around 15 seconds. You should be able to see four water stripes on the floor. If this is not the case, or if one or more water stripes only consist out of a few droplets, the wetting strips are partially or fully blocked and you can rinse them under the tap (see 'Clearing blockages from the wetting strips of the AquaSpin nozzle'). If that does not help, you can try to carefully open the holes with a needle.
		If you have checked the above and there is still no water on the floor, take the appliance to a Philips service center or contact the Consumer Care Center.
There is more water on the floor or in the After-Clean tray than usual.	The water channel of the wet module and/or AquaSpin nozzle is polluted or blocked.	Use the cleaning brush and clean the water channel of the wet module and/or AquaSpin nozzle (see 'Removing blockages from the Vacuum & Mop set-up').
	The dirty water tank is not placed correctly.	Place the dirty water tank into the appliance properly (see 'AUTOCLEAN after every use'). It is closed correctly when you can hear a 'click' sound.
The appliance leaves water traces on the floor.	You have moved the appliance sideways.	To prevent water traces on the floor, try to make less strong turns with your AquaTrio 9000 Series and avoid moving the appliance sideways. You can activate the water absorption mode by pressing the cleaning mode button. All the remaining water on your floor will be absorbed.
	You made strong turns with the appliance.	To prevent water traces on the floor, try to make less strong turns with your AquaTrio 9000 Series and avoid moving the appliance sideways. You can activate the water absorption mode by pressing the cleaning mode button. All the remaining water on your floor will be absorbed.
	You have lifted the appliance over a threshold, carpet or	Make sure the microfiber brushes stay in contact with the floor. Make sure water

Problem Possible cause Solution

	stairs. absorption mode is switched on before you lift the appliance over a threshold, carpet or stairs to prevent water traces on the floor or to prevent water from splashing from the AquaSpin nozzle (see 'Usage restrictions').
	You lifted the appliance up from the floor immediately after you switched it off.	Switch on water absorption mode to absorb any remaining water. Move the appliance forwards and backwards a few times with water absorption mode engaged before switching it off. If you switch off the appliance and lift it up immediately afterwards, the water that was present between the brushes leaves a trace of water on the floor (see 'Usage restrictions').
	The wheels are blocked. Check the condition of the wheels. Remove the dirt that blocks the wheels.
The appliance does not clean as well as it used to.	The clean water tank is empty. Refill the clean water tank (see 'Using the Vacuum & Mop set-up').
	The water strips are blocked. Remove the two microfiber brushes, fill the clean water tank with some water, and switch the appliance on. Make small forward and backward movements on the same position for around 15 seconds. You should be able to see four water stripes on the floor. If this is not the case, or if one or more water stripes only consist out of a few droplets, the water strips are partially or fully blocked and you can rinse them under the tap (see 'Clearing blockages from the wetting strips of the AquaSpin nozzle'). If that does not help, you can try to carefully open the holes with a needle.
	The inside of the AquaSpin nozzle is too dirty.	Run the AUTOCLEAN program before returning to cleaning. If there is dirt accumulation in the edges of the nozzle, remove it. Make sure to use the AUTOCLEAN function after each use (see 'AUTOCLEAN after every use').
	The microfiber Brushes are not present.	Place the microfiber brushes in the AquaSpin nozzle (see 'AUTOCLEAN after every use').
		If you have checked the above and the appliance still does not clean well, take it to a Philips service center or contact the Consumer Care Center.

Problem Possible cause Solution

Bigger dirt particles are not sucked up anymore and fall back on the floor.	The water channel of the wet module and/or AquaSpin nozzle is polluted or blocked.	Use the cleaning brush and clean the water channel of the wet module and/or AquaSpin nozzle (see 'Removing blockages from the Vacuum & Mop set-up').
The floor dries with stripes. You may have used too much detergent.		Make sure to use the right amount of detergent (see 'Using the Vacuum & Mop set-up').
	The wheels are dirty. Remove the dirt from the wheels.
There is too much foam while cleaning, but also during AUTOCLEAN.	You may have used too much detergent.	Make sure to use the right amount of detergent (see 'Using the Vacuum & Mop set-up').
	There are still detergent residues on the floor.	Clean the floor without detergent several times. Wait a moment before going over the same stain again.
It is difficult to clean stains. You may have used too little water or taken too little time to clean the stain.		Apply water and wait a moment. For example you can go with the appliance over the stain to apply water and come back to the same stain in the end of the cleaning session.
The sound of the appliance changed while cleaning.	There might be hairs or other obstacles entangled around the microfiber brushes	Remove the microfiber brushes and check for obstacles and remove them (see 'Cleaning the AquaSpin nozzle').
The display indicates that the dirty water tank is full (code: i1) and shuts down, although the dirty water tank is not full yet.	There may be foam or contamination of the dirty water tank.	Restart the appliance. If that does not solve the problem, clean the dirty water tank. If foaming is the issue, make sure you do not use more than the recommended amount of detergent (see 'Using the Vacuum & Mop set-up').
Water drips out of the appliance after it is switched off.	The appliance leaves a puddle on the floor because you did not move it while switching it off. This is normal.	The appliance can leave a small puddle of water on the floor if you do not move the appliance while switching it off. You can reduce the size of the puddle by moving the appliance while switching it off. When you switch off the appliance, it will switch to water absorption mode 4 or 4 seconds to clean up any water remaining in the nozzle. If needed, you can remove the last drops with a cloth.
	The appliance is dripping when carrying it over the floor (holding it in the air).	While cleaning, do not lift the AquaSpin nozzle from the floor, as this leaves water traces. Only move forwards and backwards.
	Water leaks from the clean water tank because you overfilled the clean water tank.	Do not fill the clean water tank beyond the MAX indication. If you do, water may spill from the clean water tank when you fasten the cap (see 'Using the Vacuum & Mop set-up').

Problem Possible cause Solution

	There is a crack in one of the tanks.	If one of the tanks is damaged, take it to a Philips service center or contact the Consumer Care Center.
I cannot remove the microfiber brushes.	Hair and/or dirt is entangled in the microfiber brushes.	Use the cleaning brush handle to remove the microfiber brushes from the AquaSpin nozzle. Remove entangled hair or dirt (see 'Cleaning the AquaSpin nozzle'). If it is difficult to pull the brushes out, you can give them a push from below the AquaSpin nozzle.
I cannot move the appliance forward or backward.	One or more wheels may be blocked by a small object.	Switch off the appliance and remove the nozzle. Then check the small and the big wheels for blockage. Remove any object that could block the wheel(s). Put the appliance upright again and resume cleaning.
The appliance has a lower suction power than usual.	The water channel of the wet module and/or AquaSpin nozzle is polluted or blocked.	Use the cleaning brush and clean the water channel of the wet module and/or AquaSpin nozzle (see 'Removing blockages from the Vacuum & Mop set-up').
	The mesh in the dirty water tank was not dry enough before being used again.	Clean and dry the dirty water tank.
	Hair entanglement on the microfiber brushes.	Switch the appliance off and remove the hair from the microfiber brushes (see 'Cleaning the AquaSpin nozzle').
	The dirty water tank is not placed correctly.	Place the dirty water tank into the appliance properly (see 'AUTOCLEAN after every use'). It is closed correctly when you can hear a 'click' sound.
The microfiber brushes do not turn anymore	The microfiber brushes are clogged with hair or dirt.	Clean the microfiber brushes with a pair of scissors or by hand (see 'Cleaning the AquaSpin nozzle').
The microfiber brushes pop out.	The microfiber brushes are not locked correctly.	Place the microfiber brushes back in the right position and lock them.
The appliance is not charging.	The power plug is not connected properly to the socket or the adapter is not inserted into the wall socket properly.	Make sure that the power plug is connected properly to the socket and that the adapter is inserted into the wall socket properly.
	The battery is not in. Please insert the battery.
	The battery is not completely inserted.	Please insert the battery until you hear a click sound.
	Wrong adapter connected. Please use the original adapter.

Problem Possible cause Solution

		If you have checked the above and the appliance still does not charge, take it to a Philips service center or contact the Consumer Care Center.
When I use my vacuum cleaner I sometimes feel static electricity shocks.	Your vacuum cleaner builds up static electricity. The lower the air humidity, the more static electricity the appliance builds up.	Make sure to touch the metal pin with your hand while holding the appliance.
	You vacuumed up dust and dirt. This also causes static electricity.	Make sure to touch the metal pin with your hand while holding the appliance.

Using the Vacuum only set-up

Problem Possible cause Solution

The appliance does not work when I push the on/off button.	You did not connect the battery.	Connect the battery to the 3-in-1 Handheld.
	The battery is empty. To charge the battery, connect the 3-in-1 Handheld with the charger (see 'Charging').
	You pushed the on/off button more than one time.	Wait a few seconds and push the on/off button again one more time.
	You did not connect the 3-in-1 Handheld to the appliance correctly.	Connect the 3-in-1 handheld correctly to the dust bucket.
	The appliance is clogged. Switch the appliance off and remove the battery or powerhouse. Then locate and remove the cause for the blockage. After that, restart the appliance. If you cannot identify the cause of the blockage, restart the appliance. This might already solve the problem.
	The roller brush is stuck. Take the roller brush out and remove any hair around the brush and the motor and place it back (see 'Cleaning the roller brush').
It is not possible, to connect the 3-in-1 Handheld to the dust bucket.	The filter case is assembled upside down.	Invert the filter case. The round opening should be visible (see 'Cleaning the dust bucket').
	The filter case is not closed properly.	Make sure you hear a click when closing the filter case. If it is difficult to close, the foam filter is probably placed upside down.

Problem Possible cause Solution

The appliance stopped working.	You accidentally touched the on/off button with your hand.	Switch on the appliance by pushing the on/off button.
	The appliance is clogged. Switch the appliance off and remove the battery or powerhouse. Then locate and remove the cause for the blockage. After that, restart the appliance. If you cannot identify the cause of the blockage, restart the appliance. This might already solve the problem.
The sound of the appliance changed while cleaning.	There might be hairs or other obstacles entangled around the roller brush.	Please check for obstacles and remove them (see 'Cleaning the roller brush').
	Obstacles are blocking the cyclone.	Check the cyclone for obstacles and remove them (see 'Cleaning the cyclone').
The appliance has a lower suction power than usual.	The filter and/or the cyclone are dirty.	Empty the dust bucket. Clean the filter and the cyclone. Make sure that you remove any hair and dirt that is stuck in the cyclone. You can remove the cyclone for easy maintenance (see 'Cleaning the cyclone'). Make sure that you wash the filter at least once a month if you use the appliance regularly (see 'Cleaning the filter').
	Something is blocking the cyclone.	Check the cyclone for objects stuck in it and remove any object that is blocking the cyclone. Make sure that you remove any hair and dirt that is stuck in the cyclone (see 'Cleaning the cyclone').
	The suction channel behind the roller brush is clogged.	Remove the roller brush and check the suction channel for obstacles and remove them.
	You have not attached the filter case properly to the dust bucket or you have not attached the dust bucket properly to the appliance. In both cases, there will be a loss of suction power.	Make sure that you attach the filter case to the dust bucket and the dust bucket to the appliance properly (see 'Cleaning the dust bucket').
	The brush is clogged with hair or dirt.	Switch the appliance off and clean the roller brush with a pair of scissors or by hand (see 'Cleaning the roller brush').
Dust escapes from the appliance.	The foam filter is not present in the filter case, or the top cover is missing.	Make sure that the filter is in the appliance and assembled correctly (see 'Cleaning the filter').

Problem Possible cause Solution

Dust escapes when opening the dust bucket.	This is normal behavior due to underpressure.	If possible, open the appliance outside.
The filter cleaning icon is shown on the display and the device shuts down.	The filter may be dirty. We advise you to clean the filter. If you cleaned the filter recently, you can disregard this icon. To continue vacuuming, click the arrow icon.
The appliance does not move smoothly across the floor when I am cleaning a carpet.	You selected a too high suction power.	Reduce the suction power by choosing setting 1 or move more slowly over the carpet.
The roller brush does not turn anymore.	The roller brush is clogged with hair or dirt.	Clean the roller brush with a pair of scissors or by hand (see 'Cleaning the roller brush').
	The roller brush may stop turning when it encounters too much resistance from high-pile carpet.	Switch off the appliance and then switch it back on again.
	You have not assembled the roller brush into the nozzle properly after cleaning.	Follow the instructions in this user manual to slide the roller brush into the nozzle properly (see 'Cleaning the roller brush'). Secure the roller brush inside the nozzle by snapping the locking lever in place.
The LEDs in the nozzle do not turn on.	You have not attached the nozzle to the tube or appliance properly.	Attach the nozzle to the tube or appliance properly. If this does not help, please take it to a Philips service center or contact the Consumer Care Center.
The appliance is not charging.	The plug is not connected properly to the socket-outlet or the adapter is not inserted into the wall socket properly.	Make sure that the plug is connected properly to the socket-outlet and that the adapter is inserted into the wall socket properly.
	The battery is not in. Please insert the battery.
	The battery is not completely inserted.	Please insert the battery until you hear a click sound.
	Wrong adapter connected. Please use the original adapter.
		If you have checked the above and the appliance still does not charge, take it to a Philips service center or contact the Consumer Care Center.
The Mini Turbo brush does not function properly.	The roller brush is blocked. Remove hairs from the brush with a pair of scissors (see 'Cleaning the Mini Turbo brush').
	The roller brush is blocked by fabric or surfaces during cleaning.	Keep the mini Turbo brush aligned with the surface and do not push the Turbo brush into soft surfaces.

Problem Possible cause Solution

	The roller brush is not properly inserted into the nozzle.	Make sure the roller brush is properly inserted into the nozzle and that there is no gap between the parts (see 'Cleaning the Mini Turbo brush').
When I use my vacuum cleaner I sometimes feel static electricity shocks.	Your vacuum cleaner builds up static electricity. The lower the air humidity, the more static electricity the appliance builds up.	Make sure to touch the metal pin with your hand while holding the appliance.
	You vacuumed up dust and dirt. This also causes static electricity.	Make sure to touch the metal pin with your hand, while holding the appliance.
Error code 'E2' appears on the display.	The temperature is too low. Make sure the temperature in the room where the appliance is used, stored, or charged is above 5 °C.
Error code 'E3' appears on the display.	The temperature is too high. Make sure the temperature in the room where the appliance is used, stored, or charged is below 35 °C. Do not expose the device to direct sunlight or high temperatures (near hot stoves, in microwave ovens, or on induction cookers). Batteries may explode if overheated.
		If you have checked the above and the appliance still does not charge, take it to a Philips service center or contact the Consumer Care Center.

Obsah

Úvod 52

Všeobecný popis 52

www.philips.com/myvacuum9000s.

Všeobecný popis

Nabíjení

Přístroj je vybaven 25V baterií Li-lon. Nabíjení trvá 4 hodiny.

www.philips.com/myvacuum9000s.

Generel beskrivelse

Opladning

17 Skyl tanken til snavset vand under vandhanen.

3 Tøm støvbeholderen i skraldespanden.

5 Ryst filterkabinettet og låget over en skraldespand for at fjerne støvet.

8 Luk filterkabinettet.

2 Skub rullebørsten tilbage i LED-mundstykket (1), og skub låseklemmen op for at låse rullebørsten i LED-mundstykket ("klik").

Aufladen

www.philips.com/myvacuum9000s.

Üldine kirjeldus

1 Tolmukambri vabastusnupp
2 Ekraan
3 Puhastusrežiimi nupp

• Tavaline niiske režiim
• Intensiivne niiske režiim
• Veeimamisrežiim

4 Keskmine nupp (AUTOCLEAN)
5 Toitenupp
6 Aku
7 Kolm-ühes käsitolmuimeja
8 Tolmukamber
9 Seinakinnitus
10 Toru
11 LED-tuledega otsak
12 Väike turbohari
13 Pikk piluotsak
14 Adapter
15 Toitepistik
16 Lisalaadija (ainult XW9385)
17 Puhastamisjärgne ja hoiustamisjaam
18 Seadme hoidik
19 Puhastamisjärgne alus
20 Alusplaat
21 Märgmoodul
22 Musta vee paak
23 Puhta vee paak
24 AquaSpini otsak
25 Mikrokiudharjad
26 Põrandapesuvedelik Philips Floor Cleaner XV1792

27 Puhastusharjake

3 Pange toru LED otsakusse.

7 Pange puhta vee paagile kork tagasi.

3 Pange toru LED otsakusse.

Hoiatus! Ärge kunagi imege seadme sisse vett ega mönda muud vedelikku.

16 Valage vesi musta vee paagist kraanikaussi.

17 Puhastage musta vee paak kraani all.

21 Pange musta vee paak tagasi seadmesse.

3 Loputage niisutusribasid kraani all.

3 Tühjendage tolmukambri sisu prügikasti.

4 Kinnitage filtrikarp tagasi tolmukambrile.

2 Tühjendage tolmukambri sisu prügikasti.

3 Loputage tolmukambri sisemust kraani all.

5 Kinnitage filtrikarp tagasi, kui tolmukamber on kuiv.

9 Pange filtrikarp koos vahtplastfiltriga tagasi tolmukambrisse.

Installation du support mural

Charge

Ako na zidnom nosaču želite pohraniti i puniti samo usisavač, pričvrstite zidni nosač na zid isporučenim vijcima. Provjerite je li zidni nosač 140 cm – 150 cm iznad poda.

i Napomena: na zidni nosač nije moguća pohrana uređaja u položaju za usisavanje i brisanje. Na zidni nosač moguće je pohraniti samo uređaj u položaju za usisavanje.
i Napomena: pobrinite se da temperatura u prostoriji u kojoj je aparat pohranjen ili se tamo puni bude između 5 °C i 35 °C.
A Oprez: budite oprezni prilikom bušenja rupa u zidu za pričvršćivanje zidnog nosača kako biste izbjegli opasnost od strujnog udara.

Sastavljanje uređaja u položaj za usisavanje i brisanje

1 Za sastavljanje uređaja u položaj za usisavanje i brisanje umetnite bateriju i pričvrstite držak 3-u-1 na modul za mokro čišćenje („klik“).

2 Pričvrstite modul za mokro čišćenje na mlaznicu AquaSpin („klik“).

3 Kako biste pohranili uređaj u položaju za usisavanje i brisanje, možete ga staviti u stanicu za postavljanje poslije čišćenja i pohranu.

i Napomena: na zidni nosač nije moguća pohrana uređaja u položaju za usisavanje i brisanje. Na zidni nosač moguće je pohraniti samo uređaj u položaju za usisavanje.

Sastavljanje uređaja u položaj za usisavanje

1 Za sastavljanje uredaja u položaj samo za usisavanje pričvrstite držak 3-u-1 na spremnik za prašinu („klik“).

2 Pričvrstite spremnik za prašinu na cijev („klik“).

4 Kako biste pohranili uređaj u položaju samo za usisavanje, stavite ga u stanicu za postavljanje poslije čišćenja i pohranu tako da prvo postavite LED mlaznicu na dulju stranu osnovne ploče, a zatim utisnete cijev u držač.

Savjet: držač za položaj za usisavanje može se pogurnuti i okrenuti naopako ako usisivač želite postaviti s druge strane stanice za postavljanje poslije čišćenja i pohranu.

Punjenje

1 Kako biste napunili uređaj, umetnite utikač u utičnicu na stražnjoj strani uredaja. Zatim umetnite prilagodnik u zidnu utičnicu.
2 Vrijednost između 0 % i 90 % treperi na zaslonu kako bi označila da se uređaj puni.

1 Za usisavanje podova od mekih ili tvrdih materijala pričvrstite držak 3-u-1 na spremnik za prašinu („klik“).

2 Pričvrstite spremnik za prašinu na cijev („klik“).

4 Za uključivanje uređaja pritisnite gumb za uključivanje/isključivanje pričekajte da uredaj bude spreman za uporabu.

Savjet: LED diode u LED mlaznici olakšavaju uočavanje prljavštine na podu. Cijev i LED mlaznica omogućuju vam da dosegnete ispod niskog namještaja bez potrebe za okretanjem uređaja.

2 Za odvajanje LED mlaznice pritisnite gumb za otpuštanje (1) i izvucite cijev ili držak iz mlaznice (2).

1 Kako biste pričvrstili četku Mini Turbo, umetnite cijev drška u četku Mini Turbo.

4 Za odvajanje četke Mini Turbo pritisnite gumb za otpuštanje (1) i izvucite držak iz četke Mini Turbo (2).

3 Za odvajanje dugačkog nastavka za uske površine pritisnite gumb za otpuštanje (1) i iz njega izvucite cijev ili držak (2).

1 Uređaj u položaju za usisavanje i brisanje postavite u stanicu za postavljanje poslije čišćenja i pohranu.

8 Izlijte sav preostali tekući deterdžent iz spremnika za čistu vodu u odvod.

9 Napunite spremnik za čistu vodu hladnom ili mlakom vodom iz slavine barem do oznake AUTOCLEAN.

A Oprez: voda iz slavine koja se ulijeva u spremnik za čistu vodu ne smije biti toplija od 50 °C.
A Oprez: nemojte upotrebljavati deterdžent za funkciju AUTOCLEAN jer bi to moglo dovesti do prekomjernog pjenjenja.

12 Kako biste pokrenuli funkciju AUTOCLEAN, pritisnite srednji gumb ●Ako je zaslon crn, najprije pritisnite gumb za uključivanje/isključivanje ●kako biste aktivirali zaslon.

13 Uređaj izvršava ciklus AUTOCLEAN.

i Napomena: ciklus Autoclean traje približno 4 minute. Za najbolje rezultate pustite da uređaj potpuno prođe kroz ciklus AUTOCLEAN. Ciklus AUTOCLEAN možete pauzirati ili otkazati u bilo kojem trenutku.

i Napomena: ako otkažete program AUTOCLEAN, uređaj će za oko 10 sekundi usisati preostalu vodu u ladici za uporabu poslije čišćenja.

16 Izlijte vodu iz spremnika za prljavu vodu u odvod.

17 Spremnik za čistu vodu operite pod mlazom vode iz slavine.

18 Mokri filtar operite pod mlazom vode iz slavine.

19 Pustite da se vlažni filtar spremnika za prljavu vodu i njegov element za protok vode potpuno osuše prije nego što ih vratite na spremnik za prljavu vodu.

20 Vratite mokri filtar u spremnik za prljavu vodu.

300 Hrvatski

21 Vratite spremnik za prljavu vodu u uređaj.

23 Kako biste omogućili da se četke od mikrovlakana osuše, stavite otvorene krajeve četki na predviđene držače stanice za postavljanje poslije čišćenja i pohranu.

i Napomena: sušenje može trajati približno 24 sata.

1 Uklonite ladicu za uporabu poslije čišćenja iz stanice za pohranu.

2 Isperite ladicu za uporabu poslije čišćenja pod mlazom vode iz slavine i ostavite da se osuši prije nego što je vratite u stanicu za pohranu.

Ako je modul za mokro čišćenje začepljen, najprije isključite uredaj i uklonite mlaznicu AquaSpin i držak 3-u-1. Zatim uklonite začepljenje pomicanjem četke za čišćenje u usisnom kanalu modula za mokro čišćenje gore-dolje.

Čišćenje začepljenja iz mlaznice AquaSpin

Ako je mlaznica AquaSpin začepljena, to se može ukloniti pomicanjem četke za čišćenje gore-dolje u usisnom kanalu mlaznice AquaSpin.

Čišćenje začepljenja s traka za vlaženje mlaznice AquaSpin

Nakon duge i česte uporabe uredaja trake za vlaženje mlaznice AquaSpin mogu se u nekom trenutku začepiti. Slijedite korake u nastavku kako biste uklonili začepljenje s traka za vlaženje mlaznice AquaSpin.

1 Uklonite poklopce traka za vlaženje s mlaznice AquaSpin tako da ih pomaknete u stranu.

2 Uklonite trake za vlaženje s mlaznice AquaSpin tako da ih povučete na stranu.

Čišćenje uređaja u položaju samo za usisavanje

Pražnjenje spremnika za prašinu

Redovito praznite spremnik za prašinu i pazite da prljavština nikada ne prijeđe oznaku „Max“. Time se sprječava ubrzano začepljenje filtra.

3 Ispraznite spremnik za prašinu u kantu za otpad.

1 Za čišćenje spremnika za prašinu i ciklonske komore uklonite kućište filtra.

2 Ispraznite spremnik za prašinu u kantu za otpad.

3 Isperite unutrašnjost spremnika za prašinu pod mlazom vode iz slavine.

4 Ostavite spremnik za prašinu da se osuši.

A Oprez: pazite da se spremnik za prašinu potpuno osuši prije nego što kućište filtra vratite u spremnik za prašinu. sušenje može trajati približno 24 sata.

6 Vratite držak 3-u-1 na spremnik za prašinu.

A Oprez: nemojte ponovno pričvršćivati držak 3-u-1 na spremnik za prašinu ako u njega nije umetnuto kućište filtra.

Čišćenje ciklonske komore

1 Okrenite ciklonsku komoru u smjeru kretanja kazaljke na satu (1) i odvojite je od spremnika za prašinu (2).
2 Uklonite dlake i prljavštinu koja se zaglavila u ciklonskoj komori i ispod nje.

Kada filtar treba očistiti, na zaslonu se pojavljuje ikona za čišćenje filtra.

9 Vratite kućište filtra zajedno s filtrom od pjene natrag u spremnik za prašinu.

A Oprez: pazite da bijeli materijal poklopca kućišta filtra bude okrenut prema gore.

A Oprez: provjerite jesu li kućište filtra i filtar od pjene potpuno suhi prije nego što ih vratite u spremnik za prašinu.

10 Vratite držak 3-u-1 na spremnik za prašinu.

A Oprez: nemojte ponovno pričvršćivati držak 3-u-1 na spremnik za prašinu ako u njega nije umetnuto kućište filtra.

1 Povucite prema dolje polugu za zaključavanje na bočnoj strani LED mlaznice (1) i izvucite valjkastu četku iz LED mlaznice (2). Zapetljane dlake ili niti možete ukloniti s valjkaste četke povlačenjem preko četke jednom rukom.

2 Gurnite valjkastu četku natrag u LED mlaznicu (1) i podignite polugu za zaključavanje kako biste zaključali valjkastu četku u LED mlaznicu („klik“).

25 Spazzole in microfibra

2 Tad AquaSpin uzgalim pievienojiet mitro moduli (atskan klikškis).

2 Tad AquaSpin uzgalim pievienojiet mitro moduli (atskan klikškis).

3 Iznemiet mitro filtru no netirā ūdens tvertnes.

4 Izlejiet üdeni no netirā üdens tvertnes izlietnē.

5 Uzlieciet mitro filtru atpakal netirā ūdens tvertnei.

13 lerice veic AUTOCLEAN ciklu.

18 Noskalojiet mitro filtru zem krāna ūdens.

20 Uzlieciet mitro filtru atpakal netirā ūdens tvertnei.

1 Iznemiet filtra apvalku, lai notīritu putekļu tvertni un ciklonisko daju.

2 Iztukšojiet puteklu tvertni atkritumu spaini.

3 Izskalojiet puteklu tvertni tekošā üdenī.

1 Nonemiet filtra pârsegu nost no puteklu tvertnes.

4 Saspiediet putu filtru, lai izspiestu üdeni.

8 Aizveriet filtra apvalku.

9 lelieciet filtra apvalku ar putu filtru atpakal puteklu tvertnē.

Nepieciešama filtra maina

Nomaina

3 Istatykite vamzdji antgalj su šviesos diodais.

Ikrovimas

Töltés

23 Schoonwaterreservoir

24 AquaSpin-mondstuk

25 Microvezelborstels

26 Philips-vloerreiniger XV1792

2 Bevestig de stofemmer op de slang ('klik').

Opladen

2 Bevestig de stofemmer op de slang ('klik').

8 Sluit de filterbehuizing.

www.philips.com/myvacuum9000s.

4 Midtre knapp (AUTOCLEAN)

5 Av/på-knapp

6 Batteri

Lading

Advarsel: Ikke sug opp vann eller andre væsker.

Advarsel: Ikke sug opp vann eller andre væsker.

Advarsel: Ikke sug opp vann eller andre væsker.

4 Hell vannet ut av spillvannsbeholderen i vasken.

10 Sett rentvannsbeholderen tilbake i apparatet.

21 Sett spillvannsbeholderen tilbake i apparatet.

3 Skyll fuktstripene under springen.

3 Rist skumfilteret over søppelkassen for å fjerne smusslaget på toppen av skumfilteret. Skyll deretter skumfilteret under springen.

8 Lukk filterhylsen.

9 Sett filterhylsen, inkludert skumfilteret, tilbake i støvbeholderen.

Det er nødvendig å skifte ut filteret

Utskiftning

www.philips.com/myvacuum9000s.

Descriere generală

Încărcare

www.philips.com/myvacuum9000s.

Splošni opis

Če želite shraniti in polniti sklop samo za sesanje na stenskem nosilcu, pritrdite stenski nosilec na steno s priloženimi vijaki. Prepričajte se, da je stenski nosilec 140–150 cm nad tlemi.

2 Mokri modul namestite na nastavek AquaSpin (zasliši se klik).

3 Nastavek za sesanje in mokro čiščenje shranite tako, da ga postavite na postajo za po čiščenju in za shranjevanje.

3 Cev vstavite v nastavek LED.

4 Če želite sklop samo za sesanje shraniti, ga postavite na postajo za po čiščenju in za shranjevanje, in sicer tako, da na daljšo stran podstavka najprej postavite nastavek LED, nato pa cev pritisnete v nosilec.

1 Nastavek za sesanje in mokro čiščenje postavite na postajo za po čiščenju in za shranjevanje.

2 Pritisnite gumb, da odklenete zbiralnik za umazano vodo in ga odstranite.

3 Mokri filter odstranite iz zbiralnika za umazano vodo.

4 Vodo iz zbiralnika za umazano vodo izlijte v korito.

5 Mokri filter namestite nazaj na zbiralnik za umazano vodo.

6 Prazen zbiralnik za umazano vodo namestite nazaj v aparat in vzemite ven zbiralnik za čisto vodo.

7 Odstranite pokrovček z zbiralnika za čisto vodo.

8 Morebitno preostalo tekočino z detergentom izlijte iz zbiralnika za čisto vodo v pomivalno korito.