LED PIX-16 - Lighting Eurolite - Free user manual and instructions
Find the device manual for free LED PIX-16 Eurolite in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LED Pixel Bar |
| Model | LED PIX-16 |
| Number of LEDs | 16 |
| LED Type | RGB SMD 5050 |
| Beam Angle | 120° |
| DMX Channels | 48 (16 RGB) or 16 (single color) |
| DMX Connector | 3-pin XLR in/out |
| Control Modes | DMX, Standalone, Master/Slave, Sound Active |
| Dimensions (L x W x H) | 1000 x 50 x 100 mm |
| Weight | 1.5 kg |
| Power Supply | AC 100-240V, 50/60Hz via included adapter |
| Power Consumption | 30 W |
| Housing Material | Aluminum |
| Mounting Options | Floor stand, hanging bracket, truss clamp |
| Cooling | Passive convection |
| IP Rating | IP20 (indoor use only) |
| Operating Temperature | 0°C to 40°C |
| Care and Cleaning | Wipe with dry cloth; do not use solvents |
| Safety Features | Overheat protection, safety cable attachment point |
| Spare Parts Available | LED modules, power supply, control board |
| Repairability | Modular design; replaceable LED boards and power supply |
| General Information | User manual included; DMX address set via DIP switches |
Frequently Asked Questions - LED PIX-16 Eurolite
How do I set the DMX address on the LED PIX-16?
Use the DIP switches on the rear panel. Each switch corresponds to a binary value (1, 2, 4, 8, etc.). Turn on switches to sum to the desired address. Refer to the manual for a full chart.
Can I mount the LED PIX-16 vertically?
Yes, the fixture can be mounted in any orientation. Use the included mounting brackets and ensure secure attachment with a safety cable.
What power supply is required?
The unit comes with an external AC adapter (100-240V AC). Do not use a different adapter as it may damage the fixture.
How do I control the LED PIX-16 without DMX?
The fixture has standalone modes including sound activation and built-in programs. Select the mode using the control panel or DIP switches.
Can I daisy-chain multiple LED PIX-16 units?
Yes, use DMX cables to connect units. In master/slave mode, set the first unit as master and the rest as slaves. Power each unit separately.
What is the maximum number of units I can daisy-chain?
You can connect up to 32 units on a single DMX line without a signal booster. For longer runs, use a DMX amplifier.
How do I replace a faulty LED?
The LED is part of a replaceable module. Open the housing, disconnect the faulty module, and snap in a new one. Ensure power is off.
Why is my LED PIX-16 not responding to DMX?
Check that the DMX address is set correctly and the cable is properly connected. Ensure the controller is sending data and the termination switch is set if needed.
Can I use the LED PIX-16 outdoors?
No, it is rated IP20 for indoor use only. Keep it away from moisture and dust.
How do I clean the LED PIX-16?
Disconnect from power. Use a soft, dry cloth to wipe the housing and lenses. Do not use any liquids or abrasive cleaners.
User questions about LED PIX-16 Eurolite
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Lighting in PDF format for free! Find your manual LED PIX-16 - Eurolite and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. LED PIX-16 by Eurolite.
USER MANUAL LED PIX-16 Eurolite
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : Eurolite
Model : LED PIX-16
Category : Lighting