FlipX FLX-S-ST - Uncategorized OPTEX - Free user manual and instructions
Find the device manual for free FlipX FLX-S-ST OPTEX in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Passive Infrared (PIR) Detector |
| Brand | Optex |
| Model | FlipX FLX-S-ST |
| Detection Range | 12 m x 12 m (90°) |
| Power Supply | 12 V DC (±10%) |
| Current Consumption | 12 mA (standby) / 25 mA (alarm) |
| Alarm Output | NC/NO relay, 30 V DC / 0.5 A |
| Tamper Output | NC, 30 V DC / 0.5 A |
| Operating Temperature | -20°C to +60°C |
| Dimensions (W x H x D) | 110 x 60 x 50 mm |
| Weight | 120 g |
| Mounting Height | 2.0 m to 3.0 m |
| IP Rating | IP54 |
| Detection Pattern | 8 zones, 4 layers |
| Pet Immunity | Up to 25 kg |
| LED Indicator | Red (alarm), Green (standby) |
| Anti-Masking | Yes |
| Warm-Up Time | Approx. 30 seconds |
| Certifications | CE, EN 50131-2-2 Grade 2 |
| Warranty | 2 years |
Frequently Asked Questions - FlipX FLX-S-ST OPTEX
How do I install the FlipX FLX-S-ST detector?
Mount the detector at a height of 2.0 to 3.0 meters on a wall or corner. Connect the power supply (12 V DC) and the alarm output to your control panel. Refer to the installation manual for detailed wiring diagrams.
What is the detection range of the FlipX FLX-S-ST?
The detector has a maximum detection range of 12 meters by 12 meters with a 90-degree angle. The pattern consists of 8 zones and 4 layers.
Can the FlipX FLX-S-ST be used outdoors?
The detector has an IP54 rating, meaning it is protected against dust and water splashes. It can be used in sheltered outdoor locations, but not exposed directly to rain.
How do I reset the FlipX FLX-S-ST after an alarm?
The detector resets automatically after the alarm signal drops. If using a latching output, power cycle the device to reset.
What should I do if the LED does not light up?
Check the power supply connections and ensure the voltage is 12 V DC. If the LED still does not light, the device may be faulty. Contact Optex support.
Is the FlipX FLX-S-ST pet immune?
Yes, it is pet immune up to 25 kg. To reduce false alarms, adjust the sensitivity and mounting height as per the manual.
How do I clean the detector?
Use a soft, dry cloth to clean the housing. Do not use water or cleaning agents. Ensure the lens is free of dust and cobwebs.
What does the tamper output do?
The tamper output is a normally closed (NC) circuit that opens when the detector cover is removed. Connect it to a 24-hour zone on your alarm panel.
Can I adjust the sensitivity of the FlipX FLX-S-ST?
Yes, there is a sensitivity potentiometer on the PCB. Turn it clockwise to increase sensitivity and counterclockwise to decrease. Use the test mode to verify.
What is the warm-up time after power is applied?
The detector requires a warm-up time of approximately 30 seconds before it stabilizes. During this time, the LED may flash and outputs may be inactive.
User questions about FlipX FLX-S-ST OPTEX
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Uncategorized in PDF format for free! Find your manual FlipX FLX-S-ST - OPTEX and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. FlipX FLX-S-ST by OPTEX.
USER MANUAL FlipX FLX-S-ST OPTEX
Manual assistant
Powered by Anthropic
Waiting for your message
Product information
Brand : OPTEX
Model : FlipX FLX-S-ST
Category : Uncategorized