NS-P350 - Loudspeaker YAMAHA - Free user manual and instructions

Product type	5.1 home theater speaker system
Brand	Yamaha
Model	NS-P350
Configuration	5 satellite speakers + 1 subwoofer
Power handling (satellites)	50 W RMS each
Power handling (subwoofer)	100 W RMS
Frequency response	28 Hz – 30 kHz
Impedance (satellites)	6 ohms
Impedance (subwoofer)	4 ohms
Satellite dimensions (W x H x D)	112 x 176 x 101 mm
Subwoofer dimensions (W x H x D)	290 x 320 x 290 mm
Satellite weight	0.7 kg
Subwoofer weight	7.5 kg
Enclosure material	MDF
Finish	Wood grain (black)
Satellite speaker driver	10 cm woofer, 2.5 cm tweeter
Subwoofer driver	20 cm woofer
Connections	Screw terminals (satellites), RCA/subwoofer input
Protection	Overload protection circuit
Maintenance	Clean with a soft, dry cloth; avoid chemicals
Safety	Do not expose to moisture, do not block vents
Repairability	Spare parts available from authorized Yamaha dealers
Included accessories	Speaker cables, instruction manual, rubber feet
Recommended use	With Yamaha AV receiver

Frequently Asked Questions - NS-P350 YAMAHA

How do I connect the NS-P350 speakers to my amplifier?

Connect each satellite to the corresponding terminals on the amplifier, respecting polarity (+/-). The subwoofer connects via a dedicated subwoofer output on the amplifier with an RCA cable.

What if the subwoofer produces no sound?

Check that the subwoofer is powered on and the RCA cable is properly connected. Ensure the amplifier is sending an LFE signal and that the subwoofer level is not set to minimum.

Can I use these speakers with an amplifier from another brand?

Yes, the NS-P350 are compatible with any 5.1 home theater amplifier, provided the power and impedance are suitable (6 ohms for satellites, 4 ohms for the subwoofer).

What is the recommended amplifier power?

An amplifier delivering between 50 and 100 W per channel is ideal. Avoid exceeding the maximum rated power to prevent damage to the speakers.

How to clean the speaker grilles?

Use a slightly damp soft cloth or a low-power vacuum cleaner with a brush. Never use chemicals or abrasive liquids.

Can the speakers be wall-mounted?

Yes, the satellites have threaded inserts on the back for wall mounting with compatible brackets. Ensure the wall can support the weight (0.7 kg per satellite).

What to do in case of sound distortion?

Reduce the amplifier volume. Distortion often occurs when the amplifier is driven into overload or equalization settings are excessive. Also check connections.

How to adjust the subwoofer level?

Use the volume knob on the back of the subwoofer. Adjust it to achieve a balanced sound, neither too weak nor too dominant. You can also adjust via the amplifier's menu.

Is there a risk of damage if I exceed the rated power?

Yes, excessive power can damage the speakers (burned voice coil, torn cone). Respect the power ratings: 50 W RMS per satellite, 100 W RMS for the subwoofer.

Where to find spare parts?

Spare parts are available from authorized Yamaha dealers or through after-sales service. Contact your local service center to order replacement speakers or grilles.

USER MANUAL NS-P350 YAMAHA

Please read the following operating precautions before use. Yamaha will not be held responsible for any damage and/or injury caused by not following the cautions below.

1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

2. Install the speakers in a cool, dry, clean place – away from windows, sources of heat, sources of excessive vibration, dust, moisture or cold. Avoid sources of electrical humming (e.g., transformers and motors). To prevent fire or electric shock, do not expose the speakers to rain or water.

3. To prevent the enclosure from warping or discoloring, do not expose the speakers to direct sunlight or excessive humidity.

4. Avoid installing the speakers where foreign objects may fall onto them and/or where they may be exposed to liquid dripping or splashing.

5. Do not place the following objects on top of the speakers:

- Other components, as they might damage or discolor the surface of the speakers.

- Burning objects (e.g., candles), as they might cause fire, damage to the speakers or personal injury.

- Containers of liquid, as they might spill and cause electric shock to the user or damage to the speakers.

1. Do not place the speakers where they are liable to be knocked over or struck by falling objects. Stable placement will also ensure better sound performance.

2. Placing the speakers on the same shelf or rack as the turntable can result in feedback.

3. Do not insert a hand or object into the port or pick up the speaker by holding the port, as it may cause personal injury or damage to the speaker.

4. Any time you note distortion, reduce the volume control on your amplifier to lower setting. Never allow your amplifier to be driven into “clipping”. Otherwise, the speakers may be damaged.

5. When using an amplifier with a rated output power higher than the nominal input power of the speakers, care should be taken not to exceed the maximum input of the speakers.

6. Do not attempt to clean the speakers with chemical solvents as this might damage the finish. Use a clean, dry cloth.

7. Do not attempt to modify or fix the speakers. Contact qualified Yamaha service personnel when service is needed. The cabinet should never be opened for any reason.

8. Secure placement or installation is the owner's responsibility. Yamaha is not liable for accidents caused by improper placement or installation of speakers.

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

Taking care of the speaker

When you wipe this unit, do not use chemical solvents (e.g., alcohol or thinners, etc.): this might damage the finish. Use a clean, dry cloth. For difficult soils, dampen a soft cloth in water, wring it out, and then wipe with the cloth.

Contents

Features ....1

Package contents....1

Installing the speakers ....1

Installing the center speaker....2

Wall-mounting the speakers....2

Connecting the speakers....3

Connection diagram....3

Removing / Attaching the grille....5

Specifications.... 5

Features

[NS-PC350]

• Type: 2-way, 3-speaker acoustic suspension speaker for center channels
  • 2-way Acoustic Suspension
• Woofer: Dual 13 cm PMD cone Tweeter: 3 cm Aluminum dome

[NS-PB350]

• Type: 2-way, 2-speaker bass-reflex speaker for main channels
• Woofer: Dual 13 cm PMD cone Tweeter: 3 cm Aluminum dome

Package contents

Make sure the package contains the following items.

Center speaker (NS-PC350)

3D rendering of a rectangular electronic device with a black body and metallic grille (no text or symbols visible)

Surround speaker (NS-PB350)

Two gray rectangular storage units with front and back panels, no visible text or symbols on the surfaces.

Fastener (for center speaker)

Speaker cable

4 m (13.1 ft.)

10 m (32.8 ft.)

Installing the speakers

** Surround left NS-PB350
** Surround right NS-PB350

Before you connect the speakers, place each speaker in its respective location. Speaker positioning is very important as it affects the overall sound quality of the system. Place the speakers in locations that will optimize the sound quality at your listening position.

Refer to the illustration.

Note

Placing the speakers too close to a CRT-type TV may impair the picture color or cause a buzzing noise. In this case, move the speakers at least 20 cm (8") away from the TV. This is not an issue with LCD and plasma TVs.

Installing the center speaker

Place the center speaker centrally between the front speakers, facing directly forward.

When placing it on a flat surface (TV rack, etc), affix the supplied fasteners to bottom of the speaker.

Refer to the illustration.

Note

Wipe the surface clean before affixing the fasteners. If the surface is dirty, oily or wet, adhesive strength is weakened and the speaker may fall.

Wall-mounting the speakers

You can mount the speakers on the wall as follows.

1 Install screws into a solid wall or wall support as shown in the illustration. Use 3.5 to 4 mm (1/8") diameter self-tapping screws.

2 Hang each speaker by its keyhole slots onto the protruding screws.

Note

Make sure the shaft of the screw is seated in the narrow part of the keyhole slot. Otherwise, the speaker may fall.

Using a commercially-available speaker stand

If you mount the speaker on a commercially-available speaker stand, use the mounting screw holes on the bottom of the speaker.

Simple line drawing of a 3D rectangular box with no text or symbols on the body, labeled 'NS-PB350' at top (no other text or symbols)

Screw holes Diameter: 4 mm (1/8") Hole depth: 10 mm (3/8")

Warning

• Do not mount the speakers on thin plywood or on a wall with a soft surface material. Otherwise, the screws may pull out of the surface and the speakers may fall, possibly damaging the speakers or causing personal injury.
• Do not install the speaker on a wall using nails, adhesives, or any other unstable hardware. Long term use and vibration may cause it to fall.
• Be careful not to pinch the speaker cables between the speaker and the speaker bracket or speaker stand.
  • To avoid accidents resulting from tripping over loose speaker cable, affix them securely to the wall.
• When using speaker brackets (commercially available) to mount the speakers on the wall or ceiling, we strongly recommend using safety wire (may be supplied with the bracket) between the speaker and bracket to prevent the speaker from falling.
• If you are not sure of a safe way to install these speakers, consult a professional installer or a building contractor.

Connecting the speakers

Note

Make sure the power cables for your other AV components are disconnected from the AC wall outlets before making any connections.

Connection diagram

graph TD
    A["Front speakers"] --> B["Right Left"]
    C["Center speaker"] --> D["Amplifier/Receiver"]
    B --> E["Speaker 1"]
    B --> F["Speaker 2"]
    D --> G["Speaker 3"]
    D --> H["Speaker 4"]
    E --> I["Left Panel"]
    F --> J["Left Panel"]
    G --> K["Left Panel"]
    H --> L["Left Panel"]
    style A fill:#f9f,stroke:#333
    style C fill:#f9f,stroke:#333
    style E fill:#ccf,stroke:#333
    style F fill:#ccf,stroke:#333
    style G fill:#ccf,stroke:#333
    style H fill:#ccf,stroke:#333
    style I fill:#cfc,stroke:#333
    style J fill:#cfc,stroke:#333
    style K fill:#cfc,stroke:#333
    style L fill:#cfc,stroke:#333

■Preparing the speaker cables

Once you've positioned the speakers, you'll need to prepare the speaker cables for connecting the speakers.

15 mm (5/8")

1 Remove about 15 mm (5/8") of insulation from the end of each speaker cable.
2 Twist the bare wires tightly.

Note

• Do not bundle or roll up excess cable.
• Twist the bare wires tightly so the individual strands are not splayed.
• Be careful not to injure yourself while preparing the speaker cables.

■Operating the speaker terminals

1 Rotate the speaker terminal counterclockwise to loosen it.
2 Insert the bare wire.
3 Rotate the speaker terminal clockwise to tighten it.
4 Test the security of the connection by pulling gently on the cable.

Note

• Make sure the terminal is gripping the bare wire, not the insulation.
• Make sure the bare wires do not touch each other, as this could damage the speaker or amplifier.
• If the connections are faulty, you will hear no sound from the speakers.

■Connecting to an amplifier

Connect each speaker to the appropriate speaker terminals on your amplifier by using the cables you prepared earlier. For details, see the “Connection diagram” (page 3).

For the surround speakers only, connect one speaker to the left (marked L) terminals of your amplifier or receiver, and another speaker to the right (marked R) terminals.

Please refer to the owner's manual that came with your amplifier or receiver.

Note

• Make sure you connect the speakers with the correct polarity—positive (+) terminals to positive (+) terminals, and negative (−) terminals to negative (−) terminals. If you get them crossed over, the sound will be unnatural and lack bass.
• In your AV receiver's speaker size settings, specify small (or "S") for all of the speakers.
• The speaker may be damaged if certain sounds are continuously output at high volume level. For example, if sine waves from a test disc, bass sounds from electronic instruments, etc., are continuously output, or when the stylus of a turntable touches the surface of a disc, reduce the volume level to prevent the speaker from being damaged.
• Once you have connected all of the speakers, plug the amplifier and other AV components into suitable AC wall outlets.
• When using an amplifier with a rated output power higher than the nominal input power of the speaker, care should be taken never to exceed the speaker's maximum input.

■When using a banana plug

1 Tighten the terminal knob.
2 Simply insert the banana plug into the terminal.

Removing / Attaching the grille

The grille is attached to protect the speaker unit, but you can remove it if necessary.

To remove the grille, hold on to both sides and slowly pull straight away from the speaker. To reattach, line up the four holes on the inside surface of the grille with the four corresponding pegs on the speaker and push gently.

NS-PB350NS-PC350

Illustration of hands installing or adjusting a speaker into a device (no text or symbols visible)

Illustration of hands installing or adjusting a panel on a speaker tower (no text or symbols present)

Note

• When removing or attaching the grille, be careful not to touch the drive units, and not to exert excessive force with any tools.
• Do not touch or apply impact to the speaker's diaphragm. Otherwise, the speaker may malfunction.
• To avoid damaging the grille, never apply excessive force, and be sure to use its frame, never pull or push the surface, for removing or attaching the grille.

Specifications

■Center speaker (NS-PC350)

Type.... 2-way Acoustic Suspension Non-Magnetic shielding type

Driver

Woofer: 13 cm (5") cone type x 2

Tweeter: 3 cm (1") aluminum dome type

Impedance ...... Nominal 6 Ω

Frequency response .... 58 Hz - 45 kHz (-10 dB) - 100 kHz (-30 dB)

Nominal input power 100 W

Maximum input power 200 W

Sensitivity 90 dB/2.83 V, 1 m

Crossover frequency.... 2.8 kHz

Dimensions (W x H x D)

.500 x 174 x 202 mm (19-5/8" x 6-7/8" x 8")

Weight 6.3 kg (13 lbs. 14 oz)

■Surround speakers (NS-PB350)

Type....2-way bass reflex Non-Magnetic shielding type

Driver

Woofer: 13 cm (5") cone type

Tweeter: 3 cm (1") aluminum dome type

Impedance ...... Nominal 6 Ω

Frequency response ....57 Hz - 45 kHz (-10 dB) - 100 kHz (-30 dB)

Nominal input power 50 W

Maximum input power 150 W

Sensitivity....88 dB/2.83 V, 1 m

Crossover frequency 3 kHz

Dimensions (W x H x D)

186 x 320 x 208 mm (7-3/8" x 12-5/8" x 8-1/4")

Weight....4.8 kg (10 lbs. 9 oz)

Précautions

3D rendering of a rectangular electronic device with a flat top and label '5.0mm' (no other text or symbols)

Enceinte Surround (NS-PB350)

Two silver rectangular speakers with black branding, shown side by side (no text or symbols visible)

Three cylindrical metal wire bundles with a 10 m4 m scale label, shown from different angles (no text or symbols on the bundles themselves)

Simple line drawing of a 3D rectangular box with no text or symbols on its faces

Illustration of hands installing a panel on a speaker into a box (no text or symbols)

Illustration of hands installing or adjusting a panel on a speaker tower (no text or symbols present)

Remarque

Dimensions (L x H x P)....186 x 320 x 208 mm

Poids.... 4,8 kg

3D rendering of a rectangular electronic device with a flat top and rounded side (no text or symbols visible)

Two gray rectangular speakers with black buttons, no visible text or symbols on the devices themselves.

Three cylindrical metal wire structures with a 10 m4 m scale label (no text or symbols on the structures themselves)

Simple line drawing of a 3D rectangular prism with no text or symbols

3D rendering of a rectangular electronic device with a flat top and rounded side (no text or symbols visible)

Altavoz Surround (NS-PB350)

Two gray rectangular speakers with black branding, no visible text or symbols on the devices themselves.

Three cylindrical metal wire bundles with a 10 m4 m scale label, no other text or symbols present.

Simple line drawing of a 3D rectangular prism with no text or symbols

Illustration of hands installing or adjusting a speaker into a device (no text or symbols visible)

Illustration of hands installing or adjusting a panel on a speaker tower (no text or symbols present)

Nota

3D rendering of a rectangular electronic device with a black body and metallic panel (no text or symbols visible)

Two silver rectangular speakers with black outlines, no visible text or symbols on the devices themselves.

Кабель колонки

Three identical cylindrical metal wire connectors arranged horizontally (no text or symbols visible)

10 m4 m

Simple line drawing of a 3D rectangular box with no text or symbols on the body, labeled 'NS-PB350' at top (no other text or symbols)

Illustration of hands installing or adjusting a panel on a box (no text or symbols visible)

Illustration of hands installing or adjusting a panel on a speaker tower (no text or symbols present)

Примечание

Important Notice: Guarantee Information for customers in EEA\* and Switzerland

English

For detailed guarantee information about this Yamaha product, and Pan-EEA* and Switzerland warranty service, please either visit the website address below (Printable file is available at our website) or contact the Yamaha representative office for your country. * EEA: European Economic Area