UAP-AC-M-PRO - Access Point Ubiquiti Networks - Free user manual and instructions

Product Type	Outdoor Wi-Fi Access Point
Brand	Ubiquiti Networks
Model	UAP-AC-M-PRO
Wi-Fi Standard	802.11ac (Wave 2)
Frequency Band	Dual-band 2.4 GHz and 5 GHz
Maximum Throughput	1,733 Mbps (5 GHz) + 400 Mbps (2.4 GHz)
MIMO	2x2:2
Connectivity	1 Gigabit RJ45 port with PoE
Power Supply	Passive PoE 24V (adapter included), compatible with 802.3af (with adapter)
Power Consumption	18W maximum
Dimensions (WxDxH)	353 x 46 x 353 mm
Weight	600 g
Protection Rating	IPX5 (weather-resistant)
Operating Temperature	-30°C to 70°C
Features	Wireless Mesh, management via UniFi Controller, VLAN, QoS
Security	WPA2-PSK, WPA-Enterprise, AES encryption
Installation	Wall or pole mount (kit included)
Maintenance	Clean with a dry, soft cloth. Do not use solvents.
Repairability	Repair by manufacturer only, no spare parts available.
Warranty	2 years
Package Contents	Access point, 24V PoE adapter, mounting kit, quick start guide

Frequently Asked Questions - UAP-AC-M-PRO Ubiquiti Networks

How to configure the UAP-AC-M-PRO access point?

To configure the UAP-AC-M-PRO, use the UniFi Controller software (available for free). Connect the access point to your network via the PoE port, launch the controller, and follow the adoption steps. You can also use the UniFi mobile app.

Can I use the UAP-AC-M-PRO with a non-Ubiquiti router?

Yes, the access point works with any router. Simply connect it to a PoE switch or use the included PoE adapter. Configuration is done via the UniFi Controller software.

How to reset the UAP-AC-M-PRO to factory settings?

To reset, press and hold the Reset button on the back of the unit for about 10 seconds until the LED flashes. Release, the device will restart with default settings.

What type of power supply is required?

The UAP-AC-M-PRO uses Passive PoE 24V. A PoE power adapter is included. It can also be powered via 802.3af PoE with an adapter (not included) or a compatible switch.

Is the access point waterproof?

Yes, it has an IPX5 rating, meaning it is resistant to water jets and suitable for outdoor use. However, it is not fully submersible.

What is the maximum WiFi range?

The range depends on the environment. Outdoors without obstacles, the range can reach 300 meters (line of sight). Indoors, it is reduced to about 50-70 meters depending on walls.

Can I create a Mesh network with multiple UAP-AC-M-PRO?

Yes, UniFi access points support Wireless Mesh. Only one needs to be wired to the network, the others will connect wirelessly. Configuration is done automatically via the controller.

How to update the firmware of the UAP-AC-M-PRO?

Updates are done via the UniFi Controller software. Connect the controller to the Internet, it will automatically download and apply available firmware updates. You can also do it manually from the interface.

Does the UAP-AC-M-PRO support VLAN?

Yes, it supports VLAN (802.1Q). You can configure multiple SSIDs with different VLANs via the controller to segment network traffic.

What to do if the LED blinks orange?

An orange LED means the access point is in adoption mode or not yet configured. Use the UniFi Controller to adopt it. If the problem persists, check the network connection and power supply.

USER MANUAL UAP-AC-M-PRO Ubiquiti Networks

Pure electrical circuit lines without any symbols

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi® 802.11AC 3x3 MIMO Outdoor Access Point with Plug & Play Mesh Technology. This Quick Start Guide is designed to guide you through installation and includes warranty terms.

Important: The UAP-AC-M-PRO requires the UniFi Controller v5.1.1 or newer, available at: downloads.ubnt.com/unifi

Package Contents

Blank white image with no visible content, text, or symbols

UniFi AP Mesh Pro Mounting

Bracket

Pole Clamps
(Qty. 2)

Carriage Bolts
(Qty. 4)

Flange Nuts
(Qty. 4)

Screws
(Qty. 4)

Screw Anchors
(Qty. 4)

Gigabit PoE Adapter
(48V, 0.5A)

Close-up of a white, flexible, coiled cable or tube with no visible text or symbols

Power Cord Quick Start

Guide

TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable ^™ is designed for outdoor installations. It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements.

Installation Requirements

• 13 mm wrench (for pole mounting)
- Cable feed must be pointed downwards when mounted.
- Shielded Category 5 (or above) cabling should be used for all outdoor wired Ethernet connections and should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit:

www.ubnt.com/toughcable

System Requirements

• Linux, Mac OS X, or Microsoft Windows 7/8/10
- Java Runtime Environment 1.6 (1.8 or newer recommended)
- Web Browser: Google Chrome (Other browsers may have limited functionality)
- UniFi Controller software v5.1.1 or newer, available at:

downloads.ubnt.com/unifi

Wireless Adoption Requirements

The UAP-AC-M-PRO supports wireless adoption into your UniFi Wi-Fi network. This feature requires a currently managed UniFi AP operating with the following configuration:

• The UniFi AP must be running firmware 3.7.7 or newer
• At least one SSID enabled and operating on 5 GHz band
• The UAP-AC-M-PRO must be within wireless range of the UniFi AP

Network Topology Requirements

• A DHCP-enabled network (for the UniFi device to obtain an IP address as well as for the wireless clients after deployment)
• A UniFi Cloud Key or management station running the UniFi Controller v5.1.1 (or newer) software, located either on-site and connected to the same Layer-2 network, or off-site in the cloud or NOC

graph TD
    A["UAP-AC-M-PRO"] --> B["UniFi Cloud Key (UniFi Controller)"]
    C["UAP-AC-M-PRO"] --> D["US-16-150W"]
    D --> E["USG-PRO-4 (DHCP Server)"]
    E --> F["WiN"]
    F --> G["Internet"]
    G --> H["Hybrid Cloud TECHNOLOGY"]
    H --> I["Remote Access to UniFi Controller"]
    B --> J["UAP-AC-M-PRO"]
    D --> K["UAP-AC-M-PRO"]

Sample Network Diagram

All UniFi devices support off-site management controllers. For setup details, see the User Guide on the website: documentation.ubnt.com/unifi

Hardware Overview

LED

LED Color Status
Flashing White Initializing.
Steady White Factory default, waiting to be integrated.
Alternating White/Blue	Device is busy; do not touch or unplug it. This usually indicates that a process such as a firmware upgrade is taking place.
Quickly Flashing Blue	Used to locate and identify a UniFi device. When the Locate feature is activated in the UniFi Controller software, the Status LED will flash blue. It will also display the location of the device on the map.
Steady Blue	Indicates the device has been successfully integrated into a network and is working properly.
Steady Blue with occasional flashing	Indicates the device is in an isolated state (all WLANs are brought down until an uplink is found).

Ports

Secondary The Secondary port is a Gigabit Ethernet port used for bridging.

Reset The Reset button serves two functions for the UniFi AP:

• Restart Press and release the Reset button quickly.
• Restore to Factory Default Settings Press and hold the Reset button for more than five seconds.

Main The Main port is a Gigabit PoE port used to connect the power and should be connected to the LAN and DHCP server. Power can be provided by one of the following:

• Gigabit PoE Adapter (included)
• Ubiquiti Networks UniFi Switch with PoE
• 802.3af/802.3at PoE+ compliant switch

Hardware Installation

The UAP-AC-M-PRO includes hardware for mounting on a pole or mast. Alternatively, it can be installed on a wall using additional fastening hardware.

Pole Mount

1. Insert two Carriage Bolts into each Pole Clamp and attach a Flange Nut on each bolt.

Two identical mechanical clamping devices with metallic rods and connectors, shown from different angles (no text or symbols visible)

Note: The mounting assembly can accommodate a ∅ 38 - 76 mm pole.

1. Remove the Mounting Bracket from the back of the UniFi AP by depressing the two snap pins.

3D rendering of a white plastic device with blue directional arrows indicating flow or movement (no text or symbols)

1. Attach one of the Pole Clamps to the pole by sliding the Carriage Bolts around the pole and into the top two slots of the Mounting Bracket.

3D rendering of a white plastic mechanical component with a cylindrical top and attached bracket (no text or symbols visible)

1. Uniformly hand-tighten each Flange Nut. Ensure the Pole Clamp is evenly clamped around the pole and tighten each Flange Nut to approximately 25 N-m.

2. Repeat steps 2 and 3 for the second Pole Clamp.

3D rendering of a mechanical clamp or bracket assembly (no text or symbols visible)

1. Attach the UniFi AP to the Mounting Bracket:

a. Position the UniFi AP with the Mounting Bracket aligned between the mounting tabs on the back of the UniFi AP.

b. Slide the UniFi AP downward into the grooves of the Mounting Bracket until the snap pins engage and lock the UniFi AP in place.

3D rendering of a mechanical assembly with a cylindrical component and a rectangular panel, no visible text or symbols

Wall Mount

To mount the UniFi AP on a wall, securely attach the Mounting Bracket to the wall using four fasteners (not included).

Note: The Mounting Bracket must attach directly to a stud or other structurally stable surface.

1. Locate the stud.
2. Position the Mounting Bracket on the stud, ensuring at least two holes are centered on the stud.
3. Mark and drill the four holes.
4. Insert the Screw Anchors in the holes as necessary.
5. Secure the Mounting Bracket to the wall the four Screws.

3D mechanical assembly diagram showing screw fasteners and a central component with mounting holes (no text or symbols)

1. Attach the UniFi AP to the Mounting Bracket:

a. Position the UniFi AP with the Mounting Bracket aligned between the mounting tabs on the back of the UniFi AP.

b. Slide the UniFi AP downward into the grooves of the Mounting Bracket until the snap pins engage and lock the UniFi AP in place.

White rectangular electronic device with a dotted connection to a small mechanical bracket (no visible text or symbols)

Connecting Ethernet

1. Press down on the center of the port cover and slide it downward to remove it.

Diagram of a device with a downward arrow and fan-like structure, no text or symbols present

1. Connect an Ethernet cable to the Main port.

White electronic device with a 3D fan-like structure and a connector pin, shown from the side (no visible text or symbols)

1. Replace the port cover.

Powering the UniFi AP

Power the UniFi AP with the included Power Adapter or an 802.3af PoE switch.

Powering with a PoE Adapter

1. Connect the Ethernet cable from the UniFi AP to the POE port of the Gigabit PoE adapter.
2. (Optional for non-mesh setup) Connect an Ethernet cable from your LAN to the LAN port of the Gigabit PoE adapter.
3. Connect the Power Cord to the adapter, and then plug the Power Cord into a power outlet.

Three white network switches connected by cable and a black device (no visible text or symbols)

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes.
2. Pre-drill the holes if necessary, and secure the bracket using two fasteners (not included).
3. Align the slots on the adapter with the tabs of the PoE Mounting Bracket, and then slide the adapter down.

Three-step diagram showing a pencil inserting into a device, then to switch to a network port (no text or symbols present)

640-00241-05

Powering with a PoE Switch

Connect the Ethernet cable from the UniFi AP directly to a PoE port on an 802.3af switch. PoE will automatically be enabled.

Illustration of a network switch connected to a device with a cable (no text or symbols visible)

Connected to UniFi Switch, model US-24-250W

Wireless Adoption

See the Wireless Adoption Requirements on page 3 before proceeding.

1. Ensure the UAP-AC-M-PRO is powered on, and then launch the UniFi Controller software.

2. Go to the Devices page, and the UAP-AC-M-PRO will show up as Pending Approval (Wireless).

3. Click Adopt.

For information on configuring and using the UniFi Controller software, refer to the User Guide located on our website:

documentation.ubnt.com/unifi

Software Installation

If you are not running the UniFi Controller software version 5.1.1 or newer, download and install the latest version from: downloads.ubnt.com/unifi

Launch the software and follow the on-screen instructions. Step-by-step instructions are available in the User Guide.

After you have installed the software and run the UniFi Installation Wizard, a login screen will appear for the UniFi Controller management interface. Enter the Username and Password that you created and click Log In.

You can adopt devices, manage your wireless network, and view network statistics using the UniFi Controller management interface.

Mobile App Installation

Ubiquiti Networks also offers the UniFi mobile app, which is available from the App Store (iOS) or Google Play™ Store (Android). You can use it to provision a UniFi AP for basic functionality without configuring a UniFi Controller. It also allows seamless provisioning of APs for remote controllers (controllers not on the same layer-2 network) and easy access to both local controllers and those monitored on unifi.ubnt.com.

Specifications

UAP-AC-M-PRO
Dimensions 343.2 x 181.2 x 60.2 mm	(13.51 x 7.13 x 2.37")
Weight 633 g (1.40 lb)
Networking Interface (2) 10/100/1000 Ethernet Ports
Buttons Reset
Power Method 802.3af PoE
Power Supply 48V, 0.5A PoE Gigabit Adapter (Included)
Supported Voltage Range 44VDC to 57VDC
Max. Power Consumption 9W
Max. TX Power
2.4 GHz	22 dBm
5 GHz	22 dBm
MIMO
2.4 GHz	3 x 3
5 GHz	3 x 3
Throughput Speeds*
2.4 GHz	450 Mbps
5 GHz	1300 Mbps
Range* 183 m (600 ft)
Antennas (3) Dual-Band Internal
Antenna Gain 8 dBi
Wi-Fi Standards 802.11 a/b/g/n/ac
Wireless Security WEP, WPA-PSK, WPA Enterprise (WPA/WPA2, TKIP/AES)
BSSID	Up to Four per Radio
Mounting	Wall/Pole (Pole Kit Included)
Operating Temperature	-40 to 70°C (-40 to 158°F)
Operating Humidity	5 - 95% Noncondensing
Certifications	CE, FCC, IC

* Speed and Range values may vary and are based on optimal environments.

Safety Notices

1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can be submerged by water.

WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer's label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet.

a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment.
d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection.
e. Protective bonding must be installed in accordance with local national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc ("UBIQUITI NETWORKS") warrants that the product(s) furnished hereunder (the "Product(s)") shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS' sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks' authorized representatives, or as approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;
(V) has been damaged or impaired as a result of using third party firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of the RMA.

In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed.

Returns

No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS' facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYER'S EQUIPMENT OR THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyer's selection of products (including the Products) for buyer's application and/or failure of products (including the Products) to meet government or regulatory requirements.

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This radio transmitter (FCC: SWX-UAPACMPRO) has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Antenna Information: Dual-band antenna, Gain: 8 dBi

Industry Canada

CAN ICES-3(A)/NMB-3(A)

This Class A digital apparatus complies with Canadian ICES-003.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This radio transmitter (IC: 6545A-UAPACMPRO) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Antenna Information: Dual-band antenna, Gain: 8 dBi

CAN ICES-3(A)/NMB-3(A)

The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter, except as listed for this product's certification.

CE marking on this product represents the product is in compliance with all directives that are applicable to it.

Alert Sign (!) Follows CE Marking

Alert sign must be indicated if a restriction on use applied to the product and it must follow the CE marking.

RoHS/WEEE Compliance Statement

English

European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

Deutsch

Declaration of Conformity

Česky [Czech]	UBIQUITI NETWORKS tímto prohlašuje, že toto UBIQUITI NETWORKS zařízení, je ve shod se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Dansk [Danish]	Hermed, UBIQUITI NETWORKS, erklærer at denne UBIQUITI NETWORKS enhed, er i overensstemmelse med de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Nederlands [Dutch]	Hierbij verklaart UBIQUITI NETWORKS, dat deze UBIQUITI NETWORKS apparaat, in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
English	Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI NETWORKS device, is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Eesti [Estonian]	Käesolevaga UBIQUITI NETWORKS kinnitab, et antud UBIQUITI NETWORKS seade, on vastavus olulistele nõuetele ja teistele asjakohastele sätetele direktiivi 1999/5/EÜ.
Suomi [Finnish]	Täten UBIQUITI NETWORKS vakuuttaa, että tämä UBIQUITI NETWORKS laite, on yhdenmukainen olennaisten vaatimusten ja muiden sitä koskevien direktiivin 1999/5/EY.
Français [French]	Par la présente UBIQUITI NETWORKS déclare que l’appareil UBIQUITI NETWORKS, est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Deutsch [German]	Hiermit erklärt UBIQUITI NETWORKS, dass sich dieses UBIQUITI NETWORKS Gerät, in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet.
Ελληνική [Greek]	Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή UBIQUITI NETWORKS, είναι σε συμμόρφωση με τις βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 1995/5/EK.
Magyar [Hungarian]	Ezennel UBIQUITI NETWORKS kijelenti, hogy ez a UBIQUITI NETWORKS készülék megfelel az alapvető követelményeknek és más vonatkozó 1999/5/EK irányely rendelkezéseit.
Íslenska [Icelandic]	Hér, UBIQUITI NETWORKS, því yfir að þetta UBIQUITI NETWORKS tæki er í samræmi við grunnkröfur og önnur viðeigandi ákvæði tilskipun 1999/5/EB.
Italiano [Italian]	Con la presente, UBIQUITI NETWORKS, dichiara che questo dispositivo UBIQUITI NETWORKS, è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti della direttiva 1999/5/CE.
Latviski [Latvian]	Ar šo, UBIQUITI NETWORKS, deklarē, ka UBIQUITI NETWORKS ierīce, ir saskaņā ar būtiskajām prasībām un citiem attiecīgiem noteikumiem Direktīvā 1999/5/EK.
Lietuviškai[Lithuanian]	UBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI NETWORKSjrenginys atitinka esminius reikalavimus ir kitas 1999/5/EBDirektyvos nuostatas.
Malti[Maltese]	Hawnhekk, UBIQUITI NETWORKS, tiddikjara li dan il-mezzUBIQUITI NETWORKS huwa konformi mar-rekwiziti essenzjali u dispożizzjonijiet rilevanti oħrajn ta ‘Direttiva 1999/5/KE.
Norsk[Norwegian]	Herved UBIQUITI NETWORKS, erklærer at denne UBIQUITINETWORKS enheten, er i samsvar med de grunnleggende kravene og andre relevante bestemmelser i direktiv 1999/5/EF.
Polski[Polish]	Niniejszym, Ubiquiti Networks, oświadcza, że urządzenie UBIQUITINETWORKS, jest zgodny z zasadniczymi wymaganiami oraz pozostalymi stosownymi postanowieniami Dyrektywy 1999/5/WE.
Português[Portuguese]	UBIQUITI NETWORKS declara que este dispositivo UBIQUITINETWORKS, está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.
Română[Romanian]	Prin prezenta, UBIQUITI NETWORKS declară că acest dispozitivUBIQUITI NETWORKS este în conformitate cu cerințele esențiale și alte prevederi relevante ale Directivei 1999/5/CE.
Slovensky[Slovak]	TýmtoUBIQUITI NETWORKS, prehlasuje, že toto UBIQUITINETWORKS zariadenie, je v súlade so základnými požiadavkami a d’alšími relevantnými ustanoveniami smernice 1999/5/ES.
Español[Spanish]	Por medio de la presente UBIQUITI NETWORKS declara que este dispositivo UBIQUITI NETWORKS, cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Svenska[Swedish]	Härmed UBIQUITI NETWORKS, intygar att denna UBIQUITINETWORKS enhet är i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Online Resources

Support help.ubnt.com

Community community.ubnt.com

Downloads downloads.ubnt.com

www.ubnt.com