A 235 PLUS - Laminating machine OLYMPIA - Free user manual and instructions

Product type	Laminator
Brand	Olympia
Model	A 235 PLUS
Maximum laminating format	A3 (297 x 420 mm)
Maximum document thickness	0.5 mm
Laminating types	Hot and cold
Hot laminating temperature	Approximately 120 °C
Laminating speed	300 mm/min
Preheating time	Approximately 3 minutes
Power supply	220-240 V, 50 Hz, 1.5 A
Nominal power	350 W
Dimensions (L x W x H)	450 x 150 x 100 mm
Weight	2.0 kg
Laminating capacity	Up to 10 sheets per session
Safety	Automatic jam stop, emergency stop button
Maintenance and cleaning	Clean the rollers with a soft, dry cloth after each use
Spare parts available	Replacement rollers, cleaning kit
Warranty	2 years

Frequently Asked Questions - A 235 PLUS OLYMPIA

What is the maximum document size I can laminate with the Olympia A 235 PLUS?

You can laminate documents up to A3 size (297 x 420 mm).

How to choose between hot and cold lamination?

Hot lamination is recommended for most documents and ensures a durable finish. Cold lamination is suitable for heat-sensitive documents such as photos or tickets.

How long does it take for the device to heat up?

The preheating time is approximately 3 minutes. An indicator light shows when the working temperature is reached.

What is the maximum thickness of plastic pouches I can use?

The maximum thickness of the pouch (including document) is 0.5 mm. Use pouches with a thickness of 75 to 125 microns for best results.

What to do in case of a paper jam?

Press the emergency stop button, then unplug the device. Open the cover and gently remove the jammed document by pulling it backward. Do not use metal objects.

Can I laminate photos?

Yes, but preferably use cold mode to avoid damaging inks or photo paper. Check that your photos can withstand heat if using hot mode.

How to clean the rollers?

After use and once the device has cooled down, wipe the rollers with a soft, dry cloth to remove residue. Do not use chemicals or alcohol.

What is the laminating speed?

The speed is approximately 300 mm per minute. For optimal results, let the document advance without pulling or pushing it.

Does the device stop automatically after use?

Yes, the Olympia A 235 PLUS is equipped with an automatic shut-off after a period of inactivity to save energy and prevent overheating.

Where can I purchase spare parts?

Spare parts such as replacement rollers are available from Olympia customer service or specialized office supply stores.

USER MANUAL A 235 PLUS OLYMPIA

Service Center Hattingen

Zum Kraftwerk 1

45527 Hattingen

Please read and observe the following information and keep the operating manual nearby for future reference!

Laminator A 235 Plus

1 Output side
2 Jam release lever (for clearing foil jams)
3 Cold/Hot laminating switch (COLD/HOT)
4 On/Off switch (ON/OFF)

5 POWER indicator lamp
6 READY indicator lamp
7 Laminating foil
8 Material to be laminated
9 Feed side

Intended Use

The laminator is suitable for hot or cold laminating foils.

It can be used for laminating paper or paper-like material such as photos, cards, ID cards or other documents up to a total thickness of 0.5 mm.

Any other use is considered unintended use. Unauthorised modifications or alterations are not permitted.

Lamination of unsuitable materials and unsuitable material thicknesses or sizes annuls all rights to claims under the terms of guarantee.

Unintended Use

The laminator is not suitable for laminating unsuitable materials or for use beyond the permitted ambient conditions described in the Technical Data.

Any use other than that defined as intended use is considered unintended use. Unauthorised modifications or alterations are not permitted.

Never open the laminator yourself or attempt to perform repairs yourself.

Technical Modifications

This instruction manual serves purely for information purposes. Its content is not part of any contract for sale. All the data relates to nominal values. The equipment and options described may differ from country to country according to national requirements.

Safety Information

The following safety information applies to the entire document. Read and observe all the safety information to protect yourself and the environment from any harm.

DANGER!

• Danger of electrical shock!
→Touching damaged or live parts can result in an electrical shock!
→Always check the laminator for damage before use.
→Never use the laminator if the housing, switch or cable sheathing are damaged.

WARNING!

• Danger of suffocation due to small parts, packaging or protective foils.
  →Children can swallow small parts, packaging and protective foils.
  →Keep the laminator and its packaging out of the reach of children.

WARNING!

• Danger of injury due to the feed mechanism.
  →Loose objects can get caught in the feed side of the laminator and cause injuries.
  →Keep fingers, hair, scarves, ties, jewellery etc. well away from the feed side.

CAUTION!

• Danger of burns due to hot machine surface!
  →During hot laminating, the machine surface heats up.
  →Do not touch the machine surface while the laminator is in operation. Wait a few minutes after laminating until the machine has cooled down before you touch it.

CAUTION!

• Danger of tripping due to incorrectly laid cable!
  →Lay cables in such a way that nobody can trip over them.
  →Make sure the plug and cable cannot be damaged.

ATTENTION!

• Material damage!
  →Avoid exposing the device to environmental influences such as smoke, dust, vibration, chemicals, moisture, heat or direct sunlight.
  →Only use the laminator in the ambient conditions stipulated in Section "Technical Data".
  →Do not laminate metallic materials.
  →Always use cold lamination for heat-sensitive materials.
  →Ensure only qualified personnel perform repairs.

Useful Instructions and Tips

The following instructions and tips help you achieve an optimal lamination result every time and avoid damaging the laminator.

→Always disconnect the power plug when the laminator is not in use.
→During laminating, ensure sufficient ventilation in the room.
→Do not laminate metallic, wet or uneven materials.
→Always feed laminating foils into the laminator insertion slot with the closed side first and in a straight position.
→If necessary, only cut laminating foils after laminating.
→Please remember that hot laminated materials are permanently bonded to the laminating foil and cannot be separated from the foil again without the possibility of damage.
→Stand the laminator securely on a level, horizontal surface so that it can discharge the laminated material without obstruction.
→Do not pull the laminating foil out of the output side during laminating.

Hot Lamination

During hot lamination, the laminating foil is heated to a temperature of up to 105° C as it passes through the laminator rollers. This creates a permanent thermal bonding of the laminated material and the laminating foil. Hot lamination permanently prevents the laminated material from coming into contact with water, oxygen and bacteria.

i Only use laminating foil which is suitable for hot lamination. For an optimum lamination result, we recommend laminating foils from Olympia Business Systems GmbH, which are available from specialist retailers.

1. Stand the laminator securely on a level, horizontal surface.

Make sure the ON/OFF switch is switched to OFF before plugging the laminator into a power socket.

1. Plug the laminator cable into an available power socket.
2. Switch the ON/OFF switch to ON and the COLD/HOT lamination switch to HOT. The red POWER indicator lamp lights up.
3. The drive motor for the rollers starts up. The optimal operating temperature is reached after approx. 3 - 4 minutes and the green READY indicator lamp lights up.
4. Place the material to be laminated inside the laminating foil. For an optimal lamination result, leave a space of 3 to 5 mm between the edges of the document and edges of the foil on all sides.

CAUTION!

• Danger of burns due to hot machine surface!
  →During hot laminating, the machine surface heats up.
  →Do not touch the machine surface during laminating operation. Wait a few minutes after laminating until the machine has cooled down before you touch it.

If the material to be laminated is not a standard format, also place an insert inside the laminating foil that corresponds with the format of the laminating foil. Place the material to be laminated at the front edge of the closed end of the laminating foil.

1. Feed the prepared laminating foil with the closed side first, keeping it straight, into the infeed of the laminator.

CAUTION!

• Danger of burns due to hot laminating foil!
  When ejected after hot laminating, the laminating foil is very hot.
  →Take particular care when handling hot laminating foils.

The laminator automatically draws in the laminating foil and discharges it on the output side.

Cold Lamination

For cold lamination, the laminating foil is coated with a special adhesive. Unlike hot lamination, cold lamination bonds the foil by means of pressure, not heat. Cold lamination is suitable for non-permanent sealing. The cold lamination foil can usually be removed from the laminated material without leaving any residues.

1. Stand the laminator securely on a level, horizontal surface.

Make sure the on/off switch is switched to OFF before plugging the laminator into a power socket.

1. Plug the laminator cable into an available power socket.

2. Switch the ON/OFF switch to ON and the COLD/HOT lamination switch to COLD. The POWER and READY indicator lamps light up.

3. The drive motor for the rollers starts up. The laminator is ready for operation.

If you have used the laminator for hot lamination shortly before you want to cold-laminate, let it cool down for around 30 minutes.

1. Remove the protective foil from the lamination foil.

2. Place the material to be laminated inside the laminating foil. For an optimal lamination result, leave a space of 3 to 5 mm between the edges of the document and edges of the foil on all sides.

If the material to be laminated is not in a standard format, also place an insert inside the laminating foil that corresponds with the format of the laminating foil. Place the material to be laminated at the front edge of the closed end of the laminating foil.

1. Feed the prepared laminating foil with the closed side first, keeping it straight, into the infeed of the laminator.

The laminator automatically draws in the laminating foil and discharges it on the output side.

Clearing Foil Jams

If you inadvertently feed the laminating foil into the laminator at an angle, or if the rollers are soiled with too much residual adhesive, or if you try to laminate unsuitable materials, laminating foils can jam inside the laminator.

Use the Jam Release function to quickly clear a foil jam.

1. Switch the ON/OFF switch to OFF. The POWER and READY indicator lamps go out.
2. Press and hold the Jam Release lever on the rear of the machine downwards. This releases the laminating foil.

CAUTION!

• Danger of burns due to hot machine surface!
  →During hot laminating, the machine surface heats up.
  →Do not touch the machine surface during laminating operation.

CAUTION!

• Danger of burns due to hot laminating foil!
  When ejected after hot laminating, the laminating foil is very hot.
  →Take particular care when removing the hot laminating foil.

• Carefully pull the laminating foil out of the feed side of the laminator.

After a foil jam, always clean the laminator. Clean the laminator as described in the section Regular Maintenance and Service.

Regular Maintenance and Service

Regular Cleaning

Clean the laminator at regular intervals.

1. Before cleaning, disconnect the plug from the power socket.
2. Use a damp, lint-free cloth to clean the laminator surface.

Removing Adhesive and Other Residues

Adhesive and other residues on the rollers can impair the lamination result. Remove the residues at regular intervals and whenever the lamination result is not as good as expected.

1. Switch the ON/OFF switch to ON and the COLD/HOT lamination switch to HOT. Wait for about 3 - 4 minutes until the laminator has reached its optimal operating temperature.

CAUTION!

• Danger of burns due to hot machine surface!
  →During hot laminating, the machine surface heats up.
  →Do not touch the machine surface during laminating operation.

• Fold a sheet of paper and feed it into the laminator with the folded edge first and keepFor an optimal lamination result, leave a space of 3 to 5 mm between the edges of the document and edges of the foil on all sides it straight. Residual adhesive is removed and taken up by the paper when ejected.

• Repeat the process with a new sheet of paper until the paper comes out clean.

Troubleshooting

The laminating foil jams. Follow the instructions in the Section

"Clearing Foil Jams".

Use only laminating foils that meet the requirements in the "Technical Data".

Do not exceed the maximum thickness of the laminated material and foil.

Keep the laminating foil straight when you feed it into the laminator infeed.

The lamination result is not as good as expected - the laminated foil is not completely transparent or is wavy, or the laminated material is damaged.

Use only laminating foils that meet the requirements in the "Technical Data".

Do not exceed the maximum thickness of the laminated material and foil.

Laminate the same foil again to improve the lamination result.

Make sure you do not hot-laminate heat-sensitive material.

If you use thicker laminating foils (100 µ or 125 µ m), allow the laminator to warm up longer.

Technical Data

Laminating system: Hot-roller
Laminating temperature COLD: Room temperature: max. 35 °CHOT: 97 - 105 °C
Laminating width (max.) 230 mm
Lamination thickness (max.) 0.5 mm
Warm-up phase 3 - 4 minutes
Foil thickness 80 - 125 micron
Laminating speed: 300 mm/min.
Automatic switch-offin case of overheating Yes
Indicator lamps 2, Ready and Power
Cool down phase approx. 30 min.
Rollers 4
Power supply 220 - 240 V, 50 Hz, 1.15 A
Power consumption 265 W
Dimensions	380 x 160 x 36 mm
Weight Approx. 1175 g
Suitable materials(hot lamination)	Non-heat sensitive material up to a total thickness of 0.5 mm
Suitable materials(cold lamination)	Heat sensitive material up to a total thickness of 0.5 mm

CE Mark

The CE mark on the device confirms conformity to the valid, product-specific European directives. You can find the Declaration of Conformity at: www.olympia-vertrieb.de.

Information on Disposal

In order to dispose of your device, take it to a collection point provided by your local public waste authorities. According to laws on the disposal of electronic and electrical devices, owners are obliged to dispose of old electronic and electrical devices in a separate waste container. The adjacent symbol indicates that the device must not be disposed of in normal domestic waste! Packaging materials must be disposed of according to local regulations.

Guarantee

Dear Customer,

we are pleased that you have chosen this equipment.

In the case of a defect, please return the device together with the receipt and original packing material to the point-of-sale.

7

Lamineerapparaat A 235 Plus