FlatPAR 151.226 - Effect machine BeamZ - Free user manual and instructions

Product type	LED effect projector
Brand	BeamZ
Model	FlatPAR 151.226
Light source	24 RGB LEDs (8 red, 8 green, 8 blue)
Rated power	30 W
Beam angle	25°
Dimensions (L x W x H)	260 x 260 x 115 mm
Weight	1.2 kg
Power supply	100-240 V AC, 50/60 Hz
Power consumption	0.5 A
Control modes	DMX512, master/slave, standalone, sound
DMX channels	3, 4, 6, or 7 channels
Built-in functions	Strobe, dimming, RGB color mixing
Color temperature	White balance adjustment
Connectivity	3-pin XLR DMX connector, IEC power connector
Cooling	Natural convection
Protection rating	IP20 (indoor use)
Mounting	Tiltable bracket with locking, clamp mounting
Included accessories	Power cable, user manual
Care and cleaning	Clean with a dry cloth; avoid solvents
Safety	Do not look directly at the light source; disconnect before maintenance
Spare parts and repairability	LEDs not individually replaceable; BeamZ after-sales service

Frequently Asked Questions - FlatPAR 151.226 BeamZ

How to connect the FlatPAR 151.226 in DMX?

Use a standard DMX cable with 3-pin XLR connectors. Set the DMX address via the buttons on the rear panel. Connect the DMX output of the controller to the DMX input of the first unit, then daisy-chain the following units.

What DMX modes are available?

The unit offers 3, 4, 6, and 7 channel modes. 3-channel mode controls red, green, blue; 4-channel mode adds dimming; 6-channel mode adds strobe and additional functions; 7-channel mode offers finer control.

How to use standalone mode?

In standalone mode, the unit operates without a DMX controller. Select a built-in program via the menu. You can adjust the speed of color changes and brightness.

How to activate sound mode?

Sound mode allows the unit to react to music. To activate it, choose master/slave mode and set the unit to master with sound sensitivity. The built-in microphone picks up ambient sound.

Can the FlatPAR be used without DMX?

Yes, the unit can operate in standalone, master/slave, or with a remote control (optional). It has built-in programs and a sound mode.

What is the lifespan of the LEDs?

The LEDs have an estimated lifespan of about 50,000 hours, under normal use and adequate ventilation. Do not obstruct the cooling vents.

How to clean the projector?

Disconnect the unit. Use a soft, dry cloth to wipe the exterior. Never use solvents, alcohol, or abrasive products. Clean the lenses regularly with a special optical product.

What to do if the unit does not turn on?

Check that the power cable is properly connected and that the power outlet works. Make sure the fuse has not blown (located near the power input). If the problem persists, contact after-sales service.

Can I replace the LEDs myself?

No, the LEDs are not individually replaceable. In case of LED failure, the unit must be repaired by an authorized technician or returned to the manufacturer.

How to set up multiple FlatPARs in master/slave?

Connect the units in a daisy chain with DMX cables. On the first unit (master), select a standalone or sound mode. On the others (slaves), set the slave mode. All slaves will follow the master's effects.

USER MANUAL FlatPAR 151.226 BeamZ

INSTRUCTION MANUAL

GEBRUIKSAANWIJZING

BEDIENUNGSANLEITUNG

MANUEL D'INSTRUCTIONS

INSTRUKCJA OBSŁUGI

ENGLISH

Congratulations to the purchase of this Beamz product. Please read this manual thoroughly prior to using the product in order to benefit fully from all features.

Read the manual prior to using the product. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock. Repairs must only be carried out by a qualified technician in order to avoid electrical shock. Keep the manual for future reference.

• Prior to using the product, please ask advice from a specialist. When the unit is switched on for the first time, some smell may occur. This is normal and will disappear after a while.
• The unit contains voltage carrying parts. Therefore do NOT open the housing.
• Do not place metal objects or pour liquids into the product. This may cause electrical shock and malfunction.
• Do not place the product near heat sources such as radiators, etc. Do not place the unit on a vibrating surface. Do not cover the ventilation holes.
• The product is not suitable for continuous use.
• Be careful with the mains lead and do not damage it. A faulty or damaged mains lead can cause electrical shock and malfunction.
• When unplugging the product from a mains outlet, always pull the plug, never the lead.
• Do not plug or unplug the unit with wet hands.
• If the plug and/or the mains lead are damaged, they need to be replaced by a qualified technician.
• If the product is damaged to such an extent that internal parts are visible, do NOT plug the unit into a mains outlet and DO NOT switch the product on. Contact your dealer. Do NOT connect the product to a rheostat or dimmer.
• To avoid fire and shock hazard, do not expose the product to rain and moisture.
• All repairs should be carried out by a qualified technician only.
• Connect the product to an earthed mains outlet (220-240Vac/50Hz) protected by a 10-16A fuse.
• During a thunderstorm or if the product will not be used for a longer period of time, unplug it from the mains. The rule is: Unplug it from the mains when not in use.
• If the product has not been used for a longer period of time, condensation may occur. Let the unit reach room temperature before you switch it on. Never use the product in humid rooms or outdoors.

• During operation, the housing becomes very hot. Do not touch it during operation and immediately after.

• To prevent accidents in companies, you must follow the applicable guide lines and follow the instructions.

• Secure the product with an extra safety chain if the unit is ceiling mount. Use a truss system with clamps. Make sure nobody stands in the mounting area. Mount the effect at least 50cm away from inflammable material and leave at least 1 meter space on every side to ensure sufficient cooling.
• This product contains high intensity LEDs. Do not look into the LED light to prevent damage to your eyes.
• Do not repeatedly switch the product on and off. This shortens the life time.
• Keep the unit out of the reach of children. Do not leave the unit unattended.
• Do not use cleaning sprays to clean switches. The residues of these sprays cause deposits of dust and grease. In case of malfunction, always seek advice from a specialist.
• Only operate the product with clean hands.
• Do not force the controls.
• If the product has fallen, always have it checked by a qualified technician before you switch the product on again.
• Do not use chemicals to clean the unit. They damage the varnish. Only clean the product with a dry cloth.
• Keep away from electronic equipment that may cause interference.
• Only use original spares for repairs, otherwise serious damage and/or dangerous radiation may occur.
• Switch the product off prior to unplugging it from the mains and/or other equipment. Unplug all leads and cables prior to moving the product.
• Make sure that the mains lead cannot be damaged when people walk on it. Check the mains lead before every use for damages and faults!
• The mains voltage is 220-240Vac/50Hz. Check if power outlet match. If you travel, make sure that the mains voltage of the country is suitable for this product.
• Keep the original packing material so that you can transport the product in safe conditions

This mark attracts the attention of the user to high voltages that are present inside the housing and that are of sufficient magnitude to cause a shock hazard.

This mark attracts the attention of the user to important instructions that are contained in the manual and that he should read and adhere to.

DO NOT LOOK DIRECTLY INTO THE LENS. This can damage your eyes. Persons who are subject to epileptic attacks should be aware of the effects that this light effect may have on them.

The product has been certified CE. It is prohibited to make any changes to the product. They would invalidate the CE certificate and their guarantee!

NOTE: To make sure that the unit will function normally, it must be used in rooms with a temperature between 5° C/41°F and 35° C/95°F.

Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or your dealer about the way to proceed. The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice. prior notice.

Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the product. This would also invalid your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use or disrespect of the warnings contained in this manual. Beamz cannot be held responsible for personal injuries caused by a disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.

UNPACKING INSTRUCTION

CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling. Save the package and all packing materials. In the event that the product must be returned to the factory, it is important that the product be returned in the original factory box and packing.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

POWERSUPPLY

On the label on the backside of the product is indicated on this type of power supply must be connected. Check that the mains voltage corresponds to this, all other voltages than specified, the light effect can be irreparably damaged. The product must also be directly connected to the mains and may be used. No dimmer or adjustable power supply.

Always connect the device to a protected circuit (circuit breaker or fuse). Make sure the device has an appropriate electrical ground to avoid the risk of electrocution or fire.

INSTALLATION

CAUTION: Please consider the respective national norms during the installation! The installation must only be carried out by an authorized employee or dealers!

Attention:

• The installation of the product has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation.
• The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
  • Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
• The operator has to make sure that safety-relating and machine-technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time.
• The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled person once a year.
• The fixture should be installed in the position where persons cannot reach and where persons may walk by or be seated.

CAUTION: When installing the device, make sure there is no highly in inflammable material (decoration articles, etc.) in between a distance of min 0.5 meter.

DISPLAY

The control board offer several features: you can simple set the starting address, run the pre-programmed program or make a reset. The main menu is accessed by pressing the Mode-button, browse through the submenu by pressing Up or Down.

Press the Enter-button in order to select the desired menu.

You can change the selection by pressing Up or Down. Confirm every selection by pressing the Enter-button.

You can leave every mode by pressing the Mode-button. The functions provided are described later in this manual.

DMX-512 CONNECTION

If you are using a standard DMX controller, you can connect the DMX-output of the controller directly to the DMX-input of the first unit in a DMX-chain. Always connect the output of one unit with the input of the next unit until all units are connected. If you use a controller with 5 pin DMX connection you will need to use a 5-pin to 3-pin adapter.

At the last fixture, the DMX cable has to be terminated. Solder a 120 Ohm resistor between signal (-) and signal (+) into a 3-pin XLR connector and plug this into the DMX output of the last fixture in the chain.

The master/slave operation enables that several same units can be controlled by one "master" unit.

Connect the first unit "DMX OUT" socket with the second unit "DMX IN", using a 3pin DMX Cable. Repeat this process with the third, fourth etc. or see a above section "DMX-512 connection". Choose the unit that will control all other and set this in master-mode via display. The other units that must react on the master, you must set in slave-mode. The "Slave" will synchronously follow the "Master".

Noted: Any unit can be the "Master" or "Slave".

HOW TO CONTROL THE UNIT

The LED FlatPAR has five operating modes:

A. Slave Mode: Set the "Master" unit to your desired mode of operation. Set the "Slave" unit in DMX mode address D001 unit will now follow the "Master".
B. DMX control mode: This function will allow you to control each individual fixtures traits with a standard DMX 512 controller.
C. Manual Mode: Adjust one of the colours to mix your desired colour.
D. Auto/Sound Mode: There are 3 Auto Modes to choose and sound modes which will react to sound.
E. IR mode: The unit can be controlled using the IR remote control

After you have selected your desired mode or setting you have to confirm it by pressing the ENTER button.

MODE	MENU	UP - DOWN
DMX Adress(ch. 1-512)
IR Controll(ON/OFF)
AUTO 1(instant)
AUTO 2(fade smooth)
AUTO 3(fade in/out)
SOUND Mode
MANUAL(colour Red)
MANUAL(colour Green)
MANUAL(colour Blue)
FLASH

DMX MODE

If control by DMX controller, then you need to set the address code to control the light, the address code value is 1-512, the light could receive the signal accordingly.

MANUAL MODE

Switch the unit on and press the MENU button until "rXXX" is displayed, you are in Red dimming mode. Press the UP and DOWN buttons to adjust intensity of the RED LEDs and confirm setting by pressing the ENTER button. When "gXXX" is displayed you are in Green dimming mode, "bXXX" is Blue mode.

AUTO/SOUND MODE

There are 3 types of Auto Modes to choose:
- Instant (PXXX)
- Smooth (LXXX)
- Fade (EXXX)
The running speed is adjustable in all 3 modes (000-255).

IR MODE

Press mode key until Iron or IroF is displayed; then press Up or Down button to choose Iron. Press ENTER to confirm.

To switch off the lights:

Press OFF on the remote control. All the lights will turn off until the button ON is pressed [1].

Manual colour control

You can set R/G/B/W colours with the remote by pushing either the Red button for red, the Green button for green, the Blue button for blue [3]. Each colour intensity is then adjustable using the Light Up and Down [2] buttons

Preset colour mode:

Press one of the twelve preset colours on the remote control [4]. No dimming possible with preset colours.

AUTO/SOUND on the IRC.

Press one of the four buttons to choose between the different auto programs. [5]

REPLACING THE FUSE

If the fuse is defective, replace the fuse with a fuse of the same type and value. Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.

Step 2: Remove the old fuse from the fuse holder.

Step 3: Install the new fuse in the fuse holder.

Step 4: Replace the fuse holder in the housing.

FIXTURE CLEANING

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit's optics.

• Make sure the area below the installation place is free from unwanted persons during servicing
• Housings, fixations and installations spots( ceiling, truss, suspensions) should be totally free from any deformation
- The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected
- In order to protect the fixture from overheat the cooling fans (if any) and ventilation openings should be cleaned monthly.

- The interior of the fixture should be cleaned annually using a vacuum cleaner or air-jet.

- Clean with soft cloth using normal glass cleaning fluid.

• Always dry the parts carefully.

- Clean the external optics at least every month. Clean the internal optics at least every 30/60 days.

ATTENTION: We strongly recommend internal cleaning to be carried out by qualified worker!

NEDERLANDS

DISPLAY

VERVANGEN ZEKERING

DISPLAY

PANEL DE CONTROL (DISPLAY)

CAMBIANDO EL FUSIBLE

AFFICHAGE

REPLACEMENT DU FUSIBLE

WYŚWIETLACZ

WYMIANA BEZPIECZNIKA

LED : 18x1Watt (6x Red, 6x Green, 6x Blue)

Fuse : F5A

Control Signal : DMX signal

Channel : 6 Channels

Function : DMX, IR, Auto, Sound active and Master-Slave.

Dimensions per unit : 218 x 218 x 72mm

Weight (per unit) : 1.3kg

The specifications are typical. The actual values can slightly change from one unit to the other. Specifications can be changed without prior notice.

tronios

Sound & Light

CE Declaration of Conformity

Manufacturer: TRONIOS BV

Regulatory Requirement: EN 60598-1/-2-17

EN 55015

EN 61547

EN 61000-3-2/-3-3

I hereby declare that the product meets the requirements stated in Directives 2014/35/EU and 2014/30/EU and conforms to the above mentioned Declarations.

Almelo,

05-01-2017

Name : M. Velders

Signature :

Specifications and design are subject to change without prior notice..

www.tronios.com

Copyright © 2017 by TRONIOS the Netherlands