RB37J5225SS - Refrigerator SAMSUNG - Free user manual and instructions

Product Type	Two-door fridge-freezer
Brand	Samsung
Model	RB37J5225SS
Total net capacity	370 litres
Refrigerator capacity	265 litres
Freezer capacity	105 litres
Dimensions (H x W x D)	1780 x 700 x 670 mm
Net weight	75 kg
Electrical supply	220-240 V, 50 Hz
Climate class	SN-T (temperate to tropical)
Cooling technology	Twin Cooling Plus
Automatic defrost	No Frost fridge and freezer
Interior lighting	LED
Beverage compartment	Yes, with fresh water dispenser
Shelves	3 adjustable glass shelves in refrigerator
Door balconies	4 balcony bins in refrigerator, 2 in freezer
Vegetable drawer	2 freshness drawers
Control type	Electronic with digital display screen
Quick freeze function	Yes
Open door alarm	Yes
Noise level	39 dB
Annual energy consumption	270 kWh/year
Energy class	A+ (old class) / D (new class)
Maintenance and cleaning	Clean the interior with soapy water. Dust the condenser at the back every 6 months.
Spare parts and repairability	Available from SAMSUNG and authorized dealers. Estimated repairability index: 7.5/10

Frequently Asked Questions - RB37J5225SS SAMSUNG

How do I set the temperature on my Samsung RB37J5225SS refrigerator?

Use the digital display on the front. Press the Refrigerator or Freezer button to adjust the temperature in 1°C increments. The recommended temperature is 3°C for the refrigerator and -18°C for the freezer.

What should I do if my refrigerator is not cooling enough?

Check that the ambient temperature does not exceed 43°C, the ventilation grilles are not blocked, and the door closes properly. If the problem persists, clean the condenser at the back or contact an authorized technician.

How do I activate the quick freeze mode?

Press the Quick Freeze button (often represented by a snowflake) for 3 seconds. This mode operates for 24 to 72 hours to quickly cool fresh food placed in the freezer.

Why is there water at the bottom of the refrigerator?

This may be due to a clogged drain hole. Clean it with a pipe cleaner or a flexible rod. Also check that the evaporation tray behind the appliance is not blocked.

How do I replace the light bulb?

The model uses an integrated LED lighting that cannot be replaced individually. If it fails, contact Samsung after-sales service for repair.

The water dispenser flows slowly, what should I do?

Make sure the water tank is properly installed and the pipe is not blocked. Clean the dispenser with a cotton swab. If the flow remains low, check the water pressure.

What is the electricity consumption of this refrigerator?

The annual consumption is approximately 270 kWh/year, which corresponds to energy class A+ (old label) or D (new label). This varies depending on usage.

How do I manually defrost the freezer?

The freezer is equipped with No Frost technology that prevents frost formation. No manual defrosting is necessary. If frost appears, check the door seal.

Are the shelves and door balconies reversible?

Yes, most shelves can be removed and repositioned at different heights to suit your needs. The door balconies are also adjustable or removable.

Where can I find spare parts for this model?

You can order original parts from the official Samsung website or from authorized dealers. Use the model number RB37J5225SS to identify the parts. The estimated repairability index is 7.5/10.

USER MANUAL RB37J5225SS SAMSUNG

French - Français ......9

German - Deutsch ......17

Dutch - Nederlands......25

Italian - Italiano 33

Hungarian - Magyar ....57

Polish - Polski......65

Czech - Čeština....73

Slovakian - Slovenčina......81

Serbian - Srpski......97

Greek - ελληνικά......105

Croation - Hrvatski......121

Albanian-Shqip 129

Norwegian - Norsk......177

Finnish - Suomi ....185

Swedish - Svenska......193

Slovenian - Slovenščina ..... 201

1. You can check where to buy replacement parts at http://samsung.com/support
2. Visit the part purchase site and enter the model code of your product to check the parts available for purchase. The model code is labelled on the outer side of your product.

- You can check the model code and version on the barcode label at the bottom left of the product.

1. For replacement parts, make sure the part name matches that of the illustration in this manual.

- User-serviceable parts are limited to handles (some models only), gaskets, drawers, and hinges.

NOTE

Following the repair by a non-authorised service provider, self-repair or non-professional repair of the product, Samsung is not liable for any damage to the product, any injury or any other product safety issue caused by any attempt to repair the product which does not carefully follow these repair and maintenance instructions. Any damage to the product caused by an attempt to repair the product by any person other than a Samsung certified service provider will not be covered by the warranty.

CAUTION

• The part name listed on the site may differ from that in this manual. Please make sure you choose the right part name. • Replacing hinges requires extreme caution because it involves detaching the door.

- Be sure to wear safety gloves while making repairs.

The actual image and provided parts of the refrigerator may differ, depending on the model and the country.

01 Top hinge

03 Drawer

05 Middle hinge

07 Bottom hinge

02 Gasket

04 Handles (Applicable models only)

06 Barcode label

Handle replacement

Model name looks like this: RB29F*, RB29H*, RB30J*, RB31F*, RB31H*, RB33J*, RB34J*, RB3CJ* What replaces the asterisks may differ depending on the model.

Asterisk(s) in the model code indicate a variant model and may replace (0-9) or (A-Z) in the model code.

CAUTION

• When replacing the door handle, take care not to scratch the front of the door.
• Firmly press the handles at the supports. Make sure there is no gap between the supports and the door.
• Tightly fasten the screws when attaching the handle.
• Check that the handle is firmly attached before using the product.

Tools required (not provided)

Philips screwdriver Flat-head screwdriver

To detach the handles

NOTE

This procedure applies to both the fridge and freezer compartment.

1. Use a flat-head screwdriver to remove the screw covers.
2. After detaching the handle, attach the screw covers back on the screw holes.
3. Use a Phillips screwdriver to remove the screws and detach the handle.

NOTE

Use these screws to fasten the handle on the opposite side.

1. Assemble the new handle in the reverse order of disassembly.

Gasket replacement

CAUTION

Make sure you firmly attach the gasket. Otherwise, cold air from the refrigerator may leak.

To remove the gasket

Open the door and remove the gasket from the door.

To replace the gasket

Attach a new gasket to the refrigerator door. Make sure there is no gap between the new gasket and the door.

Drawer replacement

CAUTION

Check that the drawer is inserted properly into the rail during assembly.

To remove the drawer

Gently lift up the front of the drawer and slide it out.

To reattach the drawers

Reattaching the drawers follows the reverse order of their respective removal steps.

Hinge replacement

To replace the hinges, you must remove the doors first.

CAUTION

• When removing the doors, take extreme caution because the doors are heavy.
• Before replacing the hinges, put a soft pad such as cardboard on the floor to prevent scratches on the door when you place the doors down.
• As the hinges must be handled carefully and replaced by two or more persons, we recommend you to call for professional technical service. • If you remove the hinge without holding the door, the door may fall and cause injury.
• Ensure that the shaft is firmly tightened on the hinge.
• Check that the hinge is firmly attached to the cabinet.
• Make sure the wire connectors are connected properly.
• Be careful not to damage the wires when fastening the top cover.

WARNING

• Tilting/laying the refrigerator requires a minimum of 2 people.
• Disconnect the power cord before reversing the doors.

Tools required (not provided)

Philips screwdriver, flat-head screwdriver, 11 mm spanner

10 mm socket wrench, 8 mm socket wrench, 10 mm spanner

Reversing the door

NOTE

For the models with handles, reverse the handles first. (For detailed information, see the "Reversing the door handle position (For models with bar handles)" section.)

1. Remove the Cover Wire Door (1). Disassemble the Cap space Door (2).

1. Remove the Cover Hinge to push a hook
2. Insert a flat-head screwdriver and put it back
3. Lever up the cover and push a hook (Take care not to damage the Cover Hinge Wire by pushing it too hard)
4. Disassemble it by pushing

1. Disconnect the wiring connector for the fridge door.

- This step may not apply to some models.

CAUTION

Do not pull the connectors too hard.

1. Remove the screws.

- (Be careful not to drop the door when you disassemble it.)

1. Remove the fridge door from the middle hinge by carefully lifting the door straight up.

CAUTION

The door is heavy, be careful not to injure yourself when removing the door.

1. Disassemble the middle hinge by removing the screws using a Phillips Head (+) screwdriver.

CAUTION

The freezer door may fall forward, so please support the door.

1. Remove the freezer door from the bottom hinge by carefully lifting the door straight up.

CAUTION

The door is heavy; be careful not to injure yourself when removing the door.

1. With the freezer door sitting on the bottom hinge (A), slowly pull the bottom hinge (A) to remove it from the holder on the bottom of the refrigerator. Once the bottom hinge (A) is removed from the holder, remove it from the freezer door, and then pull the freezer door down to remove it from the middle hinge (B).

CAUTION

To prevent the freezer door from falling, make sure to hold the freezer door tight until it is safely removed from the middle hinge (B).

1. Use a Phillips screwdriver and socket wrench (10 mm) to remove the screws fastening the middle hinge (A).
2. Reassemble in the opposite order of disassembly after replacing the top, middle, and/or bottom hinge.

CAUTION

- Make sure the wire connectors are connected properly.

- Be careful not to damage the wires when fastening the top cover.

To remove the gasket

Phillips screwdriver Flathead screwdriver

flathead

To separate the handles

NOTE

To remove the drawer

To put the drawers back

1. Use a flathead screwdriver to remove the screw covers.

- After separating the handle, put the screw covers back on the screw holes.

1. Using a Phillips screwdriver, remove the screws and separate the handle.

NOTE

Use these screws to attach the handle on the opposite side.

Attach the new gasket to the refrigerator door. Make sure there are no gaps between the new gasket and the door.

Replacing the drawer

CAUTION

Check that the drawer is correctly positioned on the rails during assembly.

To remove the drawer

Gently lift the front of the drawer and pull it out.

To reattach the drawers

Reinstalling the drawers follows the reverse order of the steps for removing them.

Replacing the hinge

To replace the hinges, you must first remove the door.

! CAUTION

• When removing the door, be extremely careful because the door is heavy.
• Before replacing the hinges, place a soft surface, such as cardboard, on the floor to prevent scratches on the door when you remove it.
• Since the hinges need to be handled carefully and two or more people should be involved in their replacement, we recommend that you call a professional technical service.
• If you remove the hinge without holding the door, the door may fall and cause injury.
• Make sure the axle is firmly tightened on the hinge. •Check that the hinge is securely attached to the cabinet.
• Make sure the wire connectors are properly connected.
• Be careful not to damage the wires when attaching the top cover.

WARNING

• Tilting / positioning the refrigerator should be done by at least 2 people.
• Disconnect the power cord before starting to reverse the door.

1. Remove the hinge cover to push the hook.
2. Insert a flat-head screwdriver and pull it back.
3. Lift the cover and push the hook (Be careful not to damage the hinge cover wire by pressing it too hard).
4. Disassemble by pushing.

1. Disconnect the wiring connector on the refrigerator door.

1. Using a flat-head screwdriver, remove the screw covers.
2. After detaching the handle, reattach the screw covers to the screw holes.
3. Use a Phillips screwdriver to remove the screws and detach the handle.

NOTE

Use these screws to attach the handle on the opposite side.

1. Assemble the new handle in the reverse order of the disassembly steps.

Replacing the gasket

CAUTION

Open the door and remove the gasket from the door.

To replace the gasket

Attach the new gasket to the refrigerator door. Make sure there are no gaps between the new gasket and the door.

Replacing the drawer

CAUTION

Carefully lift the front of the drawer and pull it out.

To reinstall the drawers

1. Remove the hinge cover to push the hook.
2. Insert the flathead screwdriver and push it back.
3. Lift the cover and push the hook (Be careful not to damage the hinge wire by pressing it too hard).
4. Disassemble it by pushing.

1. Disconnect the wire connector for the refrigerator door.

- This step does not apply to all models.

CAUTION

Phillips screwdriver Flathead screwdriver

Attach the new gasket to the refrigerator door. Make sure there are no gaps between the new gasket and the door.

Replacing the drawer

WARNING

Gently lift the front part of the drawer and pull it out.

Reattaching the drawers

1. Remove the cover hinge to push the hook.
2. Insert the screwdriver head and put it back.
3. Pull the cover upward and push the hook (Be careful not to damage the hinge cover wire by pushing it too hard).
4. Disassemble it by pressing

1. Disconnect the wiring connector for the refrigerator door.
2. This step may not apply to some models.

CAUTION

Do not pull the connectors too hard.

1. Remove the screws.
2. (Be careful not to drop the door when disassembling it.)