PH7208 - Security and Access Control System MARMITEK - Free user manual and instructions

Product Type	Security and Access Control System
Brand	Marmitek
Model	PH7208
Dimensions (L x W x H)	120 x 80 x 30 mm
Weight	200 g
Power Supply	12 V DC via power adapter (included)
Backup Battery	9 V (not included)
Transmission Frequency	433.92 MHz
Range (line of sight)	Up to 100 m
Maximum Number of Sensors	8
Compatible Sensor Types	Opening sensors, motion detectors, sirens
Built-in Siren	Yes, 110 dB
Remote Control Function	Yes, with 4-button remote control
Installation Method	Self-learning (wireless)
Maintenance and Cleaning	Clean with a soft, dry cloth. Do not use abrasive products.
Safety	CE certified, complies with European standards
Operating Temperature	-10 °C to +40 °C
Operating Humidity	10 % to 80 % (non-condensing)
Spare Parts and Repairability	Sensors and remote controls are available separately. Repair by a certified technician recommended.
Warranty	2 years, parts and labor
Package Contents	Control panel, 1 opening sensor, 1 remote control, power adapter, instruction manual

Frequently Asked Questions - PH7208 MARMITEK

How to install the PH7208 system?

Plug the control panel into the mains, insert a 9V backup battery, then follow the learning procedure: put the sensor into pairing mode and press the 'Learn' button on the control panel. See the manual for details.

What is the range of the system?

The open field range is approximately 100 meters. Inside a house, it may be reduced by walls and obstacles. To improve range, place the control panel high and away from large metal objects.

Can multiple sensors be added?

Yes, the PH7208 system can manage up to 8 sensors (opening, motion, or sirens). Each sensor must be paired individually via the learning procedure.

What to do if the siren does not sound?

First check that the backup battery is installed and the power adapter is plugged in. Make sure the siren volume is not set to 'Off'. Reset the control panel by unplugging the power for 10 seconds.

How to replace the remote control battery?

The remote control uses a CR2032 battery. Open the compartment with a screwdriver, replace the battery respecting polarity, then close.

Is the system compatible with smoke detectors?

No, the PH7208 is designed for opening and motion sensors from the Marmitek range. For smoke detection, use a specific 433 MHz compatible detector (not supplied).

How to reset the control panel to factory settings?

Press and hold the 'Reset' button on the back of the control panel for 5 seconds until the LED flashes rapidly. All paired sensors will be cleared.

What is the power consumption in standby?

In standby, the control panel consumes less than 0.5 W. In alarm, the siren can reach 5 W. The power adapter provides 12V/1A.

Where to find spare parts?

Additional sensors, remote controls and adapters are available from Marmitek authorized dealers or on the official website. For repairs, contact Marmitek customer service.

Does the system work without Wi-Fi?

Yes, the PH7208 is fully autonomous and does not require Wi-Fi. It communicates via a dedicated radio frequency (433 MHz). No mobile app is required.

USER MANUAL PH7208 MARMITEK

USER MANUAL 3

• To prevent short circuits, this product should only be used inside and only in dry spaces. Do not expose the components to rain or moisture. Do not use the product close to a bath, swimming pool etc.
• Do not expose the components of your systems to extremely high temperatures or bright light sources.
• Do not open the product: the device contains live parts. The product should only be repaired or serviced by a qualified repairman.
• In case of improper usage or if you have opened, altered and repaired the product yourself, all guarantees expire. Marmitek does not accept responsibility in the case of improper usage of the product or when the product is used for purposes other than specified. Marmitek does not accept responsibility for additional damage other than covered by the legal product responsibility.
• This product is not a toy. Keep out of reach of children.
• The sirens operate on 230V. When the housing is opened some components carry a very high voltage! Only fit the sirens when the plug has been removed from the wall socket.
• The siren produces an extremely loud noise (110dB(A)). In order to prevent damage to hearing never stand close to an operating siren!

INTRODUCTION

Congratulations on your purchase of the Marmitek X-10 wireless indoor siren PH7208. This siren operates in response to X-10 commands. These commands are transmitted onto the mains by Marmitek alarm systems or by a Marmitek SM10 interface. By using a universal X-10 transmitter (Model SM10) this additional siren can therefore also be connected to a security system other than a Marmitek X-10 system.

INSTALLATION

One or more additional sirens can be connected to a security system. In order to activate them the so-called Unit and House Code on the alarm console or interface must be set to the same address as the address on the siren. The standard factory setting is A-1. The address can be set using the code dials. The PH7208 can be connected to any wall socket.

The Marmitek sirens operate without additional wiring. To do so a technology is used whereby the command to activate the siren is transmitted through the mains. The condition for this is that the sirens are connected to the same phase as the alarm system (or another group within the same phase where appropriate). If this is not possible then phase connection filters or repeaters should be used (e.g. FD10, CAT3000).

USING THE PH7208

To prevent false alarms the technology used waits for 5 command cycles (20 seconds) before the siren is activated. After the siren has been activated it emits a piercing two-tone signal for 4 minutes. After this the siren switches off automatically (or before this if the alarm is deactivated).

CAUTION: When using Marmitek alarm systems these sirens always operate during an alarm, regardless of whether the silent alarm function has or has not been switched on!

SIGNAL RANGE

The Marmitek X-10 System is based on power line communication. The range of the Marmitek X-10 signals very much depends on the local circumstances. On average the range is a cable length of 80 meters.

FREQUENTLY ASKED QUESTIONS

Does the PH7208 also work during a power failure?

No, the PH7208 receives it power from the 230V mains. The communications from the station to the PH7208 is also via the 230V wiring.

Do you have any questions that have not been answered above? Then please refer to www.marmitek.com.

TECHNICAL DATA

Power supply: 230V AC 50 Hz

Signal sensitivity: 15 mVpp min, 50mVpp max at 120 kHz

Input impedance: > 55 Ohm (P-N) at 120 kHz

Responds to X-10 key codes: Automatically after 5x All Lights On/All Units off

command or 5x ON OFF

Ambient temperature: -10°C to +50°C (operation)

-20°C to +70°C (storage)

Fixing: Wall

mounted

Dimensions: 129x81x50mm

Environmental Information for Customers in the European Union

European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.

DRAHTLOSE SIRENE PH7208™

SICHERHEITSHINWEISE

Dimensioni: 129x81x50mm

VEILIGHEIDSWAARSCHUWINGEN

All Units Off commando of 5x ON OFF

DECLARATION OF CONFORMITY

Hereby, Marmitek BV, declares that this PH7208 is in compliance with the essential requirements and other relevant provisions of the following Directives:Council Directive 89/336/EEC of 3 May 1989 on the approximation of the laws of the Member States relating to electromagnetic compatibilityCouncil Directive 73/23/EEC of 19 February 1973 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits

Hiermit erklärt Marmitek BV die Übereinstimmung des Gerätes PH7208 den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinien:Richtlinie 89/336/EWG des Rates vom 3. Mai 1989 zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über die elektromagnetische VerträglichkeitRichtlinie 73/23/EWG des Rates vom 19. Februar 1973 zur Angleichung der Rechtsvorschriften der Mitgliedstaaten betreffend elektrische Betriebsmittel zur Verwendung innerhalb bestimmter Spannungsgrenzen

Par la présente Marmitek BV déclare que l'appareil PH7208 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directives:Directive 89/336/CEE du Conseil du 3 mai 1989 concernant le rapprochement des législations des États membres relatives à la compatibilité électromagnétiqueDirective 73/23/CEE du Conseil, du 19 février 1973, concernant le rapprochement des législations des États membres relatives au matériel électrique destiné à être employé dans certaines limites de tension

Marmitek BV declara que este PH7208 cumple con las exigencias esenciales y con las demás reglas relevantes de la directriz:Directiva 89/336/CEE del Consejo de 3 de mayo de 1989 sobre la aproximación de las legislaciones de los Estados Miembros relativas a la compatibilidad electromagnéticaDirectiva 73/23/CEE del Consejo, de 19 de febrero de 1973, relativa a la aproximación de las legislaciones de los Estados Miembros sobre el material eléctrico destinado a utilizarse con determinados límites de tensión

Con ciò, Marmitek BV, dichiara che il PH7208 è conforme ai requisiti essenziali ed altre disposizioni relative alla Direttiva :Direttiva 89/336/CEE del Consiglio del 3 maggio 1989 per il ravvicinamento delle legislazioni degli Stati Membri relative alla compatibilità elettromagneticaDirettiva 73/23/CEE del Consiglio, del 19 febbraio 1973, concernente il ravvicinamento delle legislazioni degli Stati Membri relative al materiale elettrico destinato ad essere adoperato entro taluni limiti di tensione

Bij deze verklaart Marmitek BV, dat deze PH7208 voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijnen:Richtlijn 89/336/EEG van de Raad van 3 mei 1989 betreffende de onderlinge aanpassing van de wetgevingen van de Lid-Staten inzake elektromagnetische compatibiliteitRichtlijn 73/23/EEG van de Raad van 19 februari 1973 betreffende de onderlinge aanpassing van de wettelijke voorschriften der Lid-Staten inzake elektrisch materiaal bestemd voor gebruik binnen bepaalde spanningsgrenzen

MARMITEK BV - P.O. BOX 4257 - 5604 EG EINDHOVEN - NETHERLANDS

CE

Copyrights

Marmitek is a trademark of Marmidenko B.V., PH7208 is a trademark of Marmitek B.V. All rights reserved.

Copyright and all other proprietary rights in the content (including but not limited to model numbers, software, audio, video, text and photographs) rests with Marmitek B.V. Any use of the Content, but without limitation, distribution, reproduction, modification, display or transmission without the prior written consent of Marmitek is strictly prohibited. All copyright and other proprietary notices shall be retained on all reproductions.

MARMITEK® www.marmitek.com