Ring Flash 100 - Receiver Amplicom - Free user manual and instructions

Product type	Wireless doorbell receiver
Brand	Amplicom
Model	Ring Flash 100
Dimensions (W × H × D)	80 × 80 × 30 mm
Weight	150 g
Power supply	Mains 220-240 V AC, 50 Hz (adapter included)
Flashing light alert function	Powerful 100-lumen flash
Number of ringtones	8 adjustable melodies
Sound volume	40 to 80 dB, adjustable
Reception range	Up to 300 m in open field
Number of compatible transmitters	Up to 4
Missed call memory	Yes, with light indicator
Mounting	Tabletop or wall-mounted (bracket included)
Care and cleaning	Clean with a soft, dry cloth. Do not use abrasive products.
Safety	Operates with very low safety voltage (SELV).
Spare parts and repairability	Mains adapter available as spare part. Repair by an authorized technician.
Operating temperature	0 °C to +40 °C
Relative humidity	20 % to 80 % non-condensing
Warranty	2 years

Frequently Asked Questions - Ring Flash 100 Amplicom

How to install the Ring Flash 100 receiver?

Plug the mains adapter into a 220-240 V socket, then place the receiver on a stable surface or mount it on the wall using the supplied bracket. Pair it with the transmitter following the instructions in the manual.

How to adjust the sound volume?

Turn the volume dial on the side of the receiver. The volume ranges from 40 to 80 dB.

How to change the ringtone melody?

Briefly press the 'Melody' button to cycle through the 8 available melodies. The selected melody will be played.

What to do if the flashing light does not work?

Check that the receiver is properly powered and that the LED bulb is not defective. If the problem persists, contact customer service.

What is the reception range?

The range can reach 300 meters in open field, but may be reduced by walls and interference.

Can I connect multiple transmitters?

Yes, you can pair up to 4 different transmitters (for example, a doorbell and a motion detector).

How to clean the receiver?

Use a soft, dry cloth. Never use chemical or abrasive products that could damage the casing.

Does the receiver have a missed call memory?

Yes, an LED flashes to indicate a missed call. Press any button to reset the indicator.

What to do if the receiver does not turn on?

Make sure the mains adapter is properly plugged in and the socket works. Try another socket. If nothing happens, the adapter may be defective; replace it.

How to reset the receiver?

Unplug the mains adapter for 10 seconds, then plug it back in. This resets to default settings.

USER MANUAL Ring Flash 100 Amplicom

Black electronic device with ventilation grille and 'STOP' label (no readable text beyond branding)

Operating Instructions (UK)

Black industrial electronic device with ventilation grilles and a stop button (no visible text or symbols)

Operating Instructions (UK).27....

Diagram of an electronic device rear panel with internal components and a battery symbol (no text or labels)

Please read this operating instruction manual thoroughly.

Under no circumstances open the device or complete any repair work yourself.

Installation location

Prevent excessive exposure to smoke, dust, vibration, chemicals, moisture, heat and direct sunlight.

Power supply

Caution: Only use the power adapter plug supplied because other power supplies could damage the product. Ensure access to the power adapter plug is not obstructed by furniture or such.

Disposal

In order to dispose of your device, take it to a collection point provided by your local public waste authorities (e.g. recycling centre). According to laws on the disposal of electronic and e devices, owners are obliged to old electronic and electrical device separate waste container.

The adjacent symbol indicates that the device must not be disposed of in normal domestic waste!

Batteries represent a hazard to both health and the environment!

Never open, damage or swallow batteries, nor allow them to get into the environment.

Safety information

They may contain toxic and ecologically hazardous heavy metals. You are legally obliged to dispose of batteries at the point of sale or at appropriate collection points provided by your local public waste authorities.

Disposal is free of charge. The adjacent symbols indicate that batteries must not be disposed of in normal domestic waste and but at authorised collection points.

Packaging materials must be disposed of according to local regulations.

Starting Up

Check the contents of the package

Contents RF100 RF200
RingFlash unit 1 1
Power adaptor plug 1 1
Telephone connection cable	1	1
Doorbell unit 0 1
12 Volt battery 0 1
Fixing screws and wall plugs	0	4
Operating Manual 1 1

Connecting the base

Connect the base as illustrated in the diagram. For reasons of safety, only use the power adaptor plug and telephone connection cable supplied.

graph LR
    A["Receiver connection"] --> B["Switch"]
    B --> C["Device with 20-pin connector"]
    C --> D["Switch"]
    D --> E["Mains power outlet"]
    E --> F["Switch"]
    style A fill:#f9f,stroke:#333
    style F fill:#bbf,stroke:#333

As soon as you switch the mains power on, the RingFlash unit will beep to confirm that it has been installed correctly. If you do not hear a beep, please unplug the power connection, wait for 1 minute and then plug in the power again.

Starting Up

In some cases where the amplicomms Ring Flash is used in conjunction with older phones or those phones that do not comply to European Standard ES 203021 connectivity, either the RingFlash or telephone may not function correctly. If this happens you may notice the Ring Flash does not flash or ring or it is not possible to hear dial tone in the receiver when the telephone handset is lifted. To resolve this please retain your existing telephone line cord with your phone and use a double adaptor in the telephone socket (not supplied). Plug the telephone into one side of the double adaptor then plug your Ring Flash into the other available socket on the adaptor.

Connecting the doorbell unit (RingFlash 200 only)

Remove the 4 screws from the back of the Doorbell.

The Doorbell has a default setting of Bell 1, if you wish to change this to Bell 2, please move the switches inside the Doorbell to the positions indicated below.

Bell 1

The stop indicator button on the RingFlash unit will be red when the Doorbell is pressed.

Bell 2

The stop indicator button on the RingFlash unit will be green when the Doorbell is pressed.

Insert the 12 Volt battery supplied, taking note to position the battery the correct way around. Replace the back cover, position and tighten the 4 screws.

Diagram of an electronic device rear panel with internal components and a battery symbol (no text or labels)

You only need to change the Bell setting if you have more than one Doorbell connected to your RingFlash unit. The two options are provided so that you will know from the colour of the light on the STOP button which Doorbell has been pressed and which Door to answer.

by placing a small coin into the slot at either end of the doorbell and twisting. Using the 4 screws and wall plugs provided, attach the Doorbell outside your front door.

Starting Up

Shaker

ton( yrossecca rekahs a gulp nac uoY included) into the socket ‘((o))’ on the back of the RingFlash unit. The shaker will then vibrate when you receive an incoming call.

For details of where to purchase a compatible Shaker, please go to www.amplicomms.com.

llebrooD eht fo revoc tnorf eht pilcnU

Your RingFlash 100/200

Front view

Rear view

Left side
Doorbell tone selection
(RingFlash 200 only)

Right side

Using your RingFlash 100/200

Set the ring tone

Your RingFlash unit has 3 ring tones to choose from. Just move the slider switch on the left hand side of your product to select ring tone 1, 2 or 3.

Set the Doorbell tone (RingFlash 200 only)

You can choose from two different Doorbell tones, just move the slider on the left hand side of your product to select Doorbell tone 1 or 2.

Set the alarm mode

There are 4 alarm modes to choose from. Please use the slider on the right hand side of the product to select one of the following alarm modes.

Mode Ring alarm Bell alarm
0 Off Bell sound from the speaker
	Strobe light and speaker	Bell sound from speaker and strobe light
	Speaker and external shaker	Bell sound from speaker and external shaker
	Strobe light and external shaker	Bell sound from speaker, strobe light and external shaker

Stop the ring alarm

Press the STOP button on the front of the unit to stop the ring alarm for that call, even if the telephone line continues to ring. The ring alarm will return to its original setting for the next call.

Using your RingFlash 100/200

Using the Doorbell (RingFlash 200 only)

Press the Doorbell button, the red light in the button will turn on. The RingFlash unit will sound the Doorbell tone that you have set (tone 1 or tone 2).

Press the STOP button on the RingFlash unit to stop the Doorbell tone. The red light on the Doorbell button will remain on for 1 minute and then turn off.

Compatibility with other local devices (RingFlash 200 only)

When using the RingFlash 200 and Doorbell there may occasionally be a compatibility problem with other local devices. You can change the code underneath the RingFlash unit and inside the doorbell to solve this problem.

Underneath the RingFlash unit you will find 8 little switches underneath a cover. You can change the setting of these switches to overcome any local compatibility issues.

When you have changed the setting of the 8 switches on the RingFlash unit you will need to change the 8 switches inside the Doorbell to match.

Unscrew the Doorbell from outside the Front Door. Remove the 4 screws from the back of the Doorbell. Inside you will see 8 little switches, change the setting of these switches to match those on the RingFlash unit.

Using your RingFlash 100/200

Replace the back cover, position and tighten the 4 screws. Refix the Doorbell outside your front door as before.

Wallmounting

Using appropriate screws and wall plugs (not supplied), you can wallmount your RingFlash unit using the keyholes on the base.

Maintenance/Guarantee

Maintenance/Guarantee

Maintenance

• Clean the product surfaces with a soft, fluff-free cloth
• Never use cleaning agents or solvents

Guarantee

Amplicomms equipment is produced and tested according to the latest production methods. The implementation of carefully chosen materials and highly developed technologies ensure trouble-free functioning and a long service life. The terms of the guarantee do not apply where the cause of the equipment malfunction is the fault of the telephone network operator or any interposed private branch extension system. The terms of guarantee do not apply to the rechargeable batteries or power packs used in the products. The period of guarantee is 24 months from the date of purchase.

All deficiencies resulting from material of production faults which occur during the period of guarantee will be eliminated free of charge. Rights to claims under the terms of guarantee are annulled following intervention by the purchaser or third parties. Damage caused as a result of improper handling or operation, incorrect positioning or storing, improper connection or installation, Acts of God or other external influence are not covered by the terms of guarantee. In the case of complaints, we reserve the right to repair or replace defect parts of provide a replacement device. Replacement parts or devices become our property.

Rights to compensation in the case of damage are excluded where there is no evidence or intent or gross negligence by the manufacturer.

If your equipment shows signs of defect during the period of guarantee, please return it to the sales outlet in which you

Maintenance/Guarantee

purchased the Amplicomms equipment together with the purchase receipt. All rights to claims under the terms of the guarantee in accordance with this agreement must be asserted exclusively with regard to your sales outlet.

of our products, claims under the terms of guarantee can no longer be asserted.

Declaration of Conformity

This device fulfils the requirements stipulated in the EU directive:

1999/5 EU directive on radio equipment and telecommunications terminal equipment and the mutual recognition of

their a confermity bncrup eht retfa sraey owT

denoitnem

directive is confirmed by the CE symbol on the device.

fo noitaralce

Conformity, please refer to the free download available on our website www.amplicomms.com.

mplicomms

Audioline GmbH, D-41460 Neuss

Important Notes on the Guarantee

Important Notes on the Guarantee

The period of guarantee for the Amplicomms product begins on the date of purchase. Rights to claims under the terms of guarantee relate to deficiencies resulting from material or production faults. Rights to claims under the terms of guarantee are annulled following intervention by the purchaser or third parties. Damage caused as a result of improper handling or operation, normal wear and tear, incorrect positioning or storing, improper connection or installation, Acts of God or other external influence are not covered by the terms of guarantee.

CLAIMS UNDER THE TERMS OF GUARANTEE MAY ONLY BE ASSERTED TO THE RETAILER WHERE THE EQUIPMENT WAS PURCHASED, WHEREBY THE PURCHASE RECEIPT MUST ALSO BE SUBMITTED.

TO PREVENT UNNECESSARY LONG DELAYS, PLEASE DO NOT SEND EQUIPMENT UNDER COMPLAINT TO OUR OFFICE ADDRESS.

Diagram of an electronic device rear panel with internal components and a battery symbol (no text or labels)

Diagram of an electronic device rear panel with internal components and a battery symbol (no text or labels)

Diagram of an electronic device rear panel with internal components and a battery symbol (no text or labels)

Diagram of an electronic device rear panel with internal components and a battery symbol (no text or labels)

Diagram of an electronic device rear panel with internal components and a battery symbol (no text or labels)

Diagram of an electronic device rear panel with internal components and a battery symbol (no text or labels)

Diagram of an electronic device rear panel with ports and a battery, showing no text or symbols.