PS 45 CCD - Shredder OLYMPIA - Free user manual and instructions

USER MANUAL PS 45 CCD OLYMPIA

Exterior view of a modern glass-wrapped device with control panel and buttons (no readable text or symbols)

PS 45 CCD

Service-Center Hattingen

Important safety rules

Please read the instructions thoroughly before using the device to make sure that you are able to use all of its functions.

Keep children and pets away from the device. The device may only be used by adults.

The device can only be used by one person at a time. Do not conduct any other activities on the device (e.g. cleaning) when it is in use.

Have any necessary repairs performed by qualified specialist personnel.

Protect the device against direct sunshine, extreme heat and moisture.

Safety note:

The power socket must be located close to the equipment and be easily accessible. This enables the equipment to be disconnected from the power supply quickly in an emergency.

Warning

Keep the product out of the reach of children and pets

Keep jewellery (e.g. long neck-laces) away from the paper feed opening

Do not put your hands into the paper feed opening

Keep loose garments (e.g. ties, scarves) away from the paper feed opening

Keep long hair away from the paper feed opening

Remove other materials (e.g. paper clips or staples) from the paper before shredding

Read the instructions for use before using the document shredder

Do not splash any liquid on the shredder

Caution: failure to observe these safety symbols can lead to serious injuries. If an object (sleeve, tie, etc.) is inadvertently fed into the infeed slot, pull out the mains plug immediately.

Electrical safety guidelines

• Pull out the mains plug before emptying the collecting baskets, cleaning the device or if the device is not going to be used for a long time.
• If the mains cable, mains plug or the device itself is damaged do not operate the device any longer (danger of injuries).
• Do not overload the recommended capacity of the mains socket.
• Do not make any alterations to the mains cable as it has been designed for the specified mains voltage.

Intended use

The PS 45 CCD shredder may only be used to shred paper, CDs or credit cards in the infeed slots provided. The material to be shredded must be dry and must correspond to the specifications listed in the technical data. Shredding other materials can lead to

injuries (for example, if solid material splinters) or damage to the device (destruction of the cutting unit, etc.).

Do not shred endless paper documents with this device. Remove all paper clips and staples before feeding paper into the device.

The device may only be used indoors in dry rooms.

Parts and function

1) Paper feed opening/credit card 2) Selector Switch AUTO: the shredder is ready to work OFF: the shredder stops REV: the shredder reverses the paper when you move the switch to this position ON CD: the shredder is ready to work 3) Power indicator 4) CD feed opening 5) Power cord 6) CD waste bin 7) Waste bin

1) Paper feed opening/credit card
2) Selector switch

AUTO: the shredder is ready to work

OFF: the shredder stops

REV: the shredder reverses the paper when you move the switch to this position

ON CD: the shredder is ready to work

3) Power indicator
4) CD feed opening
5) Power cord
6) CD waste bin
7) Waste bin

Operations

1. Place the shredder head on the waste bin correctly; when you fix the shredder head in place you will hear a click when the microswitch underneath the shredder head connects correctly with the rib on the waste bin. Now connect the shredder to the mains (check the voltage), and move the selector switch to the AUTO position to operate the shredder.

PAPER/CREDIT CARD

1. Put the waste paper/credit card you want to shred into the paper feed opening vertically. The mechanical sensor inside the paper feed opening will be triggered and the shredder will start to work automatically. After shredding is finished, the shredder will run for 2-4 seconds until the motor is switched off automatically. Do not shred more than 10 sheets of paper at a time, as shown in the specifications.

CD

1. If you want to shred a CD, move the selector switch to the ON CD position and put the CD into the CD feed opening. Do not shred more than 1 CD at a time, as shown in the specifications.
2. If there is a jam, move the selector switch to the REV position and the shredder will reverse the jammed paper automatically. If you want to stop the shredder, move the selector switch to the OFF position. If the motor overheats, the shredder will be shut off automatically.

Clearing a jam

If too much paper is inserted in the cutting unit, it will cause a jam.

Proceed as follows:

• Push the sliding switch to the Paper REV position.
• The cutting unit runs backwards and pushes the excess paper back.
• Reduce the quantity and slide the switch to AUTO again. The cutting unit runs forward again and the residue remaining is shredded.
  If the backwards and forwards movement does not remedy the jam, pull out the mains plug and remove the remaining manually from the cutting unit.

Warning:

If the above method does not work with the jammed shredder, switch the shredder off and take it back to the dealer for repair.

Emptying the waste bin

1. If you want to empty the waste bin, please make sure the unit is switched off and the power cord is unplugged
2. Remove the shredder head and empty the waste paper bin and the small CD bin.
3. Replace back the shredder head on the waste bin correctly.

Warning:

Paper clogs the shredder head if the waste bin is too full. Always empty the waste bin when the bin is full.

Motor protection

The motor switches off automatically in the event of overloading. Pull out the mains plug from the socket and allow the motor to cool down to room temperature. Plug the mains cable back in and then continue operation.

Notes on care and maintenance

Caution:

Maintenance work may only be performed when the mains plug is pulled out.

Clean the housing with a slightly moist cloth.

Do not use any aggressive cleaning agents. Never use any chemicals (e.g. cleaning solvent, alcohol) to clean the housing.

To ensure your shredder enjoys a long working life, we recommend to clear residual material from the cutting units at regular intervals and apply special oil for paper shredders to the cutting unit. You can purchase a special CFC-free oil from your specialist retailer or directly from our Service Center in Hattingen. This will extend the service life of the device.

Attention: It is forbidden to use oil spray bottles containing CFC!

Technical data

Model: PS 45 CCD

Power supply: 230 V/50 Hz

Cutting width of the paper slot: 220 mm

Cutting width of the CD slot: 120 mm

Cutting power: 10 DIN A4 sheets (80 g/m²); 1 CD, 1 credit card

Shred size: 4 x 35 mm

Shred speed: 2.5 m/min

Waste bin volume: 21 l (0.8 l for CD bin)

Noise level: approx. 72 dB

Security level: 3

Max. power consumption: 1.6 A

Size (W x H x D): 360 x 244 x 400

Weight: 5 kg

Operating cycle paper/credit card: 3 min. on

Operating cycle CD: 3 min. on

Device malfunctions

Faults Cause Remedy
Device does not work	Is the mains cable plugged properly in the socket?	Plug the mains cable into the socket properly.
	Does the motor not start when paper is inserted?	Slide the paper in the respective slot so that it touches the sensor in the centre.
Device does not work after lengthy operation or stops during operation	Was the device in constant operation for some time? Is the surface of the device warm?	Pull out the mains plug from the socket and allow the motor to cool down to room temperature.
Jam Have you inserted more than 10 sheets of paper (80 g/m2) or more than 1 CD/credit card? Has the material not been inserted straight in the in-feed slot?		Set the sliding switch to REV to push back the paper. Switch the device to AUTO again to shred the paper remaining in the cutting unit.

Disposal Notes

Simple line drawing of a trash bin with crossed x- and y-axes, no text or symbols present.

This symbol [the crossed-out wheeled bin/PICTURE] means that the product should be brought to the return and or separate collection systems available to end-users, when the product has reached the end of its lifetime. This symbol applies only to the countries within the EEA (*).

(*) EEA = European Economic Area, which comprises the EU Member States plus Norway, Iceland, and Liechtenstein.

Guarantee

In the case of a defect, please return the device together with the receipt and original packing material to the point-of-sale.

OLYMPIA

PS 45 CCD

Simple line drawing of a trash bin with crossed x- and y-axes, no text or symbols present

Simple line drawing of a trash bin with crossed x- and y-axes, no text or symbols present.

Simple line drawing of a trash bin with crossed x- and y-axes, no text or symbols present.

Simple line drawing of a trash bin with crossed x- and y-axes, no text or symbols present