MSL620ERVS - Basket Pelgrim - Free user manual and instructions

USER MANUAL MSL620ERVS Pelgrim

Hand inserting a flexible plastic sheet into a metal filing tray (no text or symbols visible)

MSL620ERVS

Technical line drawing of a rectangular mechanical component with a cylindrical top and base, shown with dashed construction lines (no text or symbols)

Diagram showing two labeled arrows pointing to a textured surface, with numbers 1 and 2 indicating specific positions or features.

Technical diagram of a device with labeled components including A, G, P, L, and P.

Technical line drawing of a mechanical component with a cylindrical top and base, showing no text or symbols.

Fig. 3Fig. 2

B 420

Fig. 4

Technical line drawing of a rectangular mechanical component with a cylindrical top and base, shown with dashed construction lines (no text or symbols)

Diagram showing two labeled arrows pointing to a textured surface with numbered annotations 1 and 2.

Technical diagram of a device with labeled components including A, G, P, L, and P.

Technical line drawing of a mechanical component with a cylindrical top and base, showing no text or symbols.

Fig. 3Fig. 2

B 420

Fig. 4

Technical line drawing of a rectangular mechanical component with a cylindrical top and base, shown with dashed construction lines (no text or symbols)

Diagram showing two labeled arrows pointing to a textured surface with numbered annotations 1 and 2.

Technical diagram of a device with labeled components including A, G, P, L, and P.

Technical line drawing of a mechanical component with a cylindrical top and base, showing no text or symbols.

Abb. 3Abb. 2

B 420

Abb. 4

Erforderlicher Freiraum

	What you should pay attention to 5
	During use 5

Operation

Switching on 6Switching off 6Lighting

6

Maintenance

	Cleaning	7
	Grease filters 7

Faults

	What should I do if 9
	Faults table 9

Installation

	General	10
	Electrical connection 10
	Building in dimensions 11

Assembly

General

13

Technical data

General

14

Environmental aspects

Disposal of packaging and appliance 15

Introduction

You have selected an ATAG extractor hood.

Optimum ease of use and simple operation were the most important factors in the development of this product.

The extractor hood operates silently and provides maximum extraction effect. This banishes cooking smells completely. The WV62..AC is specially designed for use on a central extraction system and is fitted with an electric flap.

This manual describes how you can make the best possible use of your extractor hood. You can find information in it about the controls and background information about how the appliance works. You will also find tips about how to look after it.

The safety instructions that are important during the installation are included in the installation guide, which is supplied separately and is meant for the installer.

Please keep this manual carefully, since any subsequent user will also find it very useful.

What you should pay attention to

For safety tips in relation to the installation, we refer you to the instructions in the accompanying installation guide.

This extractor hood is extremely safe. There are, however, a number of things you have to pay attention to, just as for any other product.

This appliance should only be connected by a registered installer.

Repairs should only be carried out by an authorised service engineer.

Never open the casing and do not alter the mechanical and/or electrical structure of the appliance. This could result in dangerous situations (touching live components) and faults.

Do not use the appliance if it is damaged.

The appliance should be disconnected from the mains before being repaired or cleaned. Remove the plug from the socket or turn the switch in the meter cupboard to zero.

For electrical safety reasons, the appliance must not be cleaned using high-pressure cleaners or steam cleaners.

During use

Flambéing under an extractor hood is not permitted. The high flames could cause a fire.

Always keep an eye on things when deep-frying.

Switch the extractor hood on before starting to cook. Leave the extractor hood on for about ten minutes after you have finished cooking.

Clean the extractor hood regularly, as specified on page 7, "maintenance". In this way, you prevent the risk of fire.

Disconnect the extractor hood from the mains before replacing the light bulbs! Only use the same light bulbs, with the wattage stated at the inside of the hood.

Switching on

Technical line drawing of a rectangular mechanical component with a cylindrical top and base, shown with dashed lines indicating hidden edges (no text or symbols)

Pull out the lower part of the hood.

The electric flap is opened.

After switching on, wait for at least 10 seconds before switching the hood back off.

Switching off

Push the lower part of the hood back in.

The electric flap is closed.

After switching off, wait for at least 10 seconds before switching the hood back on.

Lighting

The on/off switch for the lighting is located to the lower right of the hood.

Cleaning

Enamelled extractor hoods

Clean the extractor hood with soap and a soft cloth. Then rinse with clean water. Do not use aggressive cleaning agents, such as soda. The enamel will remain attractive if you polish it with wax from time to time.

Stainless steel extractor hoods

For cleaning the stainless steel parts you can best use a mild cleaning agent (washing-up liquid) and a damp cloth. Dry with kitchen paper or a dry cloth.

The stainless steel regains its shine if you occasionally use a stainless-steel care product or polish. The polish applies a dirt-resistant layer to the stainless steel. Always clean the stainless steel in the direction of polishing.

ATAG supplies cleaning and maintenance agents for extractor hoods. For information on availability, please contact the consumer department (see warranty conditions for the phone numbers).

Never use abrasive cleaning agents (such as green scourers or other scouring pads) or polishing cleaning agents (such as liquid abrasives). Never use caustic agents. These can attack the stainless steel.

Grease filters

Clean the grease filters at least once a month. During cleaning, the aluminium parts of the filters may become dull as a result of the cleaning agents used, particularly when placed in the dishwasher. This is normal and is not covered by the warranty.

Diagram showing two labeled arrows pointing to a textured surface, with numbers 1 and 2 indicating specific positions or features.

Removing filter cassette

1 Switch off the flap and lighting.
2 Using the recess, press the filter backwards and tip it downwards at the front.
3 Remove the filter from the hood.

Cleaning

You can clean the filters in the dishwasher. Allow them to drain fully before reinstalling them in the hood.

The filters may also be cleaned by hand.

Clean the filters in water and washing-up liquid and rinse them. Allow the filters to drain fully. The underside of the extractor hood can be cleaned with a mild cleaning agent and a moist cloth. Then dry it off with kitchen towel or a dry cloth.

Reinstalling filter cassette

The filter has to be installed with the locking mechanism to the side. Open the locking mechanism. This pulls the projections to the side of the filter inwards. When installing the filters hold the locking mechanism in this position.

1 Push the projections at the side of the filter into the openings provided for this purpose at the side of the extractor hood.
2 Hinge the filter upwards.
3 Release the locking mechanism. The projections at the side of the filter move outwards into the openings provided for this purpose at the side of the extractor hood.

The filter is now correctly positioned.

What should I do if...

If the appliance does not work properly, this does not always mean that it is defective. Try to deal with the problem yourself first. Phone the service department if the advice given below does not work.

Attention

Disconnect the appliance from the mains before starting the repair, preferably by removing the plug from the socket or setting the main switch to zero.

Faults table

Symptom Possible cause Solution
Lighting is not functioning. Light bulb defective. Remove the grease filters. This gives access to the light bulbs. Unscrew the bulb from the fitting and replace it with a bulb matching the wattage stated at the inside of the hood.
Extractor hood makes a noise.	Discharge too long or too many bends in the duct. Flap defective.	Change the discharge ducting (see installation guide). Phone the service department.
No extraction. Flap or controle defective. Connection cable defective.		Phone the service department.

General

The discharge

The discharge may only be connected to a central mechanical extraction. Bear in mind the local regulations concerning the ventilation of gas appliances.

We advise the use of as large a discharge duct as possible. A duct with a smaller diameter will have a low extraction capacity and produce higher noise levels.

Bends produce resistance. Make sure that the duct has a smooth run and has as few bends as possible. Draw the flexible pipe out as far as possible. Before starting to drill, check that there are no installation pipes (for gas, water, etc.) present.

The discharge stump has a diameter of 125 mm. It is best if the discharge pipe also has this diameter.

Electrical connection

The plug should be accessible after the extractor hood is fitted or it should be possible to disconnect the extractor hood from the mains by means of a bipolar switch with a contact gap of 3 mm.

Attention

When making the electrical connections, take care that the voltage and frequency correspond to the values given on the data plate.

If the connection cable becomes damaged, it should be replaced by the manufacturer's service department or by a person with equivalent qualifications, in order to prevent dangerous situations from arising.

Attention

Make sure that there is a sufficient supply of fresh air, if an extractor hood and a heat source (e.g. gas cooker) that both consume air from the same room, are switched on at the same time. The maximum permitted underpressure is 4 Pa.

Building in dimensions

min 20 - max 40 12 420

165 135 30

512 21,5 469 21,5 31 297 270 Ø125 600 65 131 258 31

Fig. 1

Technical diagram of a device with labeled components including A, G, P, L, and directional arrows indicating assembly or assembly.

Technical line drawing of a rectangular electronic component with a cylindrical top and base, showing no text or symbols.

Fig. 3Fig. 2

B 420

Fig. 4

Clearance required

The distance between the underside of the extractor hood and the hob should be at least 550 mm. For gas hobs, this distance should be a minimum of 650 mm.

General

Mounting of the cooker hood on the lower side of the cupboard.

• Mounting the cooker hood on the lower side of the cupboard.
• For fixing use 4 screws suitable for the cupboard, using the holes in Fig.1.
• When mounting align the front of the cooker hood to the door of the cupboard. Mount and regulate the L wall spacer and fix with the screws marked P (Fig 3).

General

This appliance conforms to current CE guidelines.

Type MSL620
Power supply 230 V AC	- 50 Hz
Connected load see data plate
Dimensions (wxhxd) 600 x 165 x 290 mm

Disposal of packaging and appliance

The appliance's packaging is recyclable. The following may be used:

• cardboard;
  • polyethylene film (PE);
  • CFC-free polystyrene (PS rigid foam).

Dispose of these materials responsibly and in accordance with government regulations.

The government can also provide information about the responsible disposal of discarded domestic appliances.