MSK600ERVS - Basket Pelgrim - Free user manual and instructions

USER MANUAL MSK600ERVS Pelgrim

Exterior view of a stainless steel kitchen range hood (no text or symbols visible)

MSK600ERVS

MSK900ERVS

Handleiding

Afzuigkap

Instructions for use

Cooker hood

Illustration of a hand inserting a card into a folder (no text or symbols visible)

Diagram showing a device with labeled components and signal paths, including a sensor or sensor device and directional arrows.

Montage

Diagram of a mechanical or electrical system with labeled components A, B, and E, showing directional arrows and components.

Technical diagram of a mechanical assembly with labeled components A, B, C, D, and F

Symbol of a trash bin with crossed lines indicating no waste or discharge, plus a black rectangular block below (no text or numbers present)

Diagram of a hand holding a folded paper or plastic sheet, with no visible text or symbols

Diagram of a mechanical or electrical setup with a box, wires, and directional arrows (no text or symbols)

Montage

Diagram of a water filtration or filtration system with labeled components A, B, and E, showing flow directions and components.

Technical diagram of a mechanical assembly with labeled components F, D, and C

Symbol of a trash bin with crossed x-marks and a blank base (no text or numbers)

Illustration of a hand holding a clipboard with a curved arrow inside (no text or symbols)

Diagram illustrating a mechanical or electrical setup with labeled components and directional arrows, likely representing signal or control paths.

Montage

Diagram of a mechanical or electrical system with labeled components A, B, and E, showing directional arrows and connections.

Technical diagram showing a mechanical assembly with labeled components F, D, and C, including directional arrows and dimension lines.

Symbol of a trash bin with crossed lines indicating no waste or discharge (no text or numbers present)

	Cleaning	6
	Removing the grease filters	7
	Lighting	7

Faults

	What should I do if	8
	Faults	table

Installation

	General	9
	Electrical connection	10
	Mounting the canopy hood 11

Appendice

Disposal of appliance and packaging

12

Introduction

You have selected an Pelgrim extractor hood.

Optimum ease of use and simple operation were the most important factors in the development of this product.

The extractor hood operates silently and provides maximum extraction effect. This banishes cooking smells completely. The MSK600/900 is specially designed for use on a central extraction system and is fitted with an electric flap.

This manual describes how you can make the best possible use of your extractor hood. You can find information in it about the controls and background information about how the appliance works. You will also find tips about how to look after it.

The safety instructions that are important during the installation are included in the installation guide, which is supplied separately and is meant for the installer.

Please keep this manual carefully, since any subsequent user will also find it very useful.

First read the separate safety instruction before you are going to use the appliance!

Controls

Switch hood on/off.

1. Press the on/off button A.

• The electric flap is opened.

• After switching on, wait at least 10 seconds before switching the hood back off.

1. Press the A button again.

• The electric flap is closed.

- After switching off, wait at least 10 seconds before switching the hood back on.

Switch lighting on/off.

1. Press the lighting button (B).

• The lighting comes on.

1. Press the B button again.

• The lighting goes off.

Cleaning

Attention! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse. Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket.

The cooker hood should be cleaned regularly (at least with the same frequency with which you carry out maintenance of the fat filters) internally and externally. Do not use abrasive products. Do not use alcohol!

Attention! Failure to carry out the basic cleaning recommendations of the cooker hood and replacement of the filters may cause fire risks. Therefore, we recommend oserving these instructions.

The manufacturer declines all responsibility for any damage to the hood or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations.

Cooker hood

Clean the cooker hood with soapy water and a soft cloth. Then wipe with clean water to rinse. Do not use aggressive cleaning agents such as soda. The cooker hood paintwork will stay looking nice if you wax it occasionally.

Stainless steel canopy hoods

Do not use any sort of scourer. Treat with a stainless steel care product and polish with the structure of the stainless steel.

Metal grease filters

These must be cleaned once a month (or when the filter saturation indication system – if envisaged on the model in possession – indicates this necessity) using non aggressive detergents, either by hand or in the dishwasher, which must be set to a low temperature and a short cycle. The openings must be placed downwards to let the water run out of the filters. The cleaning agents will make the aluminium filter turn dull, this is normal.

Grease filters

Illustration of a hand inserting a card into two compartments, showing internal structure (no text or symbols)

Removing the grease filters

Switch off the electricity! Remove the plug from the socket or switch the electricity off at the mains. Pull the grease filter towards you and tilt it downwards at the front.

Lighting

• The hood is equipped with a lighting system based on LED technology.
• The LEDs guarantee an optimum lighting, a duration up to 10 times as long as the traditional lamps and allow to save 90% electrical energy.
• For replacement, contact the service department.

What should I do if...

If the appliance does not work properly, this does not always mean that it is defective. Try to deal with the problem yourself first. Phone the service department if the advice given below does not work.

Attention

Disconnect the appliance from the mains before starting the repair, preferably by removing the plug from the socket or setting the main switch to zero.

Faults table

Symptom Possible cause Solution
Lighting is not functioning. LED	lamp defective. For replacement	contact the service department.
Extractor hood makes a noise.	Discharge too long or too many bends in the duct.Flap defective.	Change the discharge ducting (see installation guide).Contact the service department.
No extraction. Flap or controle	defective.Connection cable defective.	Contact the service department.

General

This appliance should be connected to the power supply by a recognized fitter who is familiar with, and works according to the correct safety regulations. This appliance meets the European requirements.

Important that you know:

• The minimum distance between the supporting surface for the cooking vessels on the gashob and the lowest part of the range hood must be not less than 65 cm. For use with an electric, ceramic or induction hob, this distance must be at least 55 cm.
• The discharge may only be connected to a central mechanical extraction.
• Consider local regulations with respect to the ventilation of gas appliances.
• The shorter the duct, and the fewer the bends in it, the better the cooker hood will work.
• Before you start drilling check that there are no installation cables present.
• The connecting pipe for the cooker hood has a diameter of 125 mm. It is best also to use a flue pipe of the same diameter.
• The installation material supplied with this range hood is designed for fixing to reinforced concrete or masonry walls. For some types of walls you may need special plugs and screws.

Connection

Electric connection

The appliance has been manufactured as a class II, therefore no earth cable is necessary.

Make sure the supply voltage ratings correspond with those stated on the appliance data plate. The connection to the mains is carried out as follows:

BROWN = phase L

BLUE = phase N

This canopy hood has been provided with a power plug. When installing the hood, make sure that this plug remains accessible. We recommend installing the wall socket out of view, behind the chimney cover.

Attention:

If you want to make a fixed connection, ensure that a multi-pole switch with a distance between contacts of 3 mm is installed in the supply cable.

max 90 cm

Diagram of a mechanical or electrical setup with a box, wires, and directional arrows indicating motion (no text or symbols present)

Mounting

- Mount the hood on the wall using the plugs and screws provided bracket (A). Check size specifications.

20 265 A

Diagram of a scientific apparatus with labeled components and directional arrows, including symbols like 'B' and 'E'.

- Adjust the width of the brackets to the width of the upper chimney. Next, mount the bracket on the wall using the plugs and the screws (B). Take into account the distance between the brackets bracket and the ceiling (Check size specifications).

Technical diagram of a mechanical assembly with labeled components F, C, and D

• Install the vent duct on the flange (C) and then onto the connecting surface of the exhaust grid.
• Put the plug in the wall socket.
• Slide the upper chimney into the lower chimney.
• Attach the lower chimney to the hood using the screws provided (D).
• Slide the upper chimney around the bracket and attach with the screws provided (E).

Disposal

Disposal of appliance and packaging

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The local authorities can provide you with the relevant information.

The packaging of this appliance is recyclable. It could have been made from:

• cardboard;
  • polythene foil (PE);
  • CFK-free polystyrene (PS-hard foam).

Symbol of a trash bin with crossed x-marks and a blank rectangular base (no text or numbers)

You need to dispose of these materials responsibly in accordance with official regulations.

To draw attention to the fact that the segregated processing of electric household appliances is compulsory, this appliance carries the symbol of a crossed-out dustbin. This means that at the end of its working life, you may not dispose of the appliance as household refuse. Instead, you should hand it in at a special refuse collection centre run by the local authority or at a dealer's providing this service.

Segregated processing of household appliances avoids any negative effects on the environment and public health that might otherwise occur.

It enables the recovery of the materials used in the production of this appliance, thus realising considerable savings in terms of raw materials and energy.

Barcode image with black and white vertical bars, no visible text or symbols

726660

Pelgrim