DW365 - Saw DEWALT - Free user manual and instructions

Product type	Circular saw
Brand	DeWalt
Model	DW365
Voltage	230 V
Input power	1350 W
Output power	800 W
No-load speed	4,000 rpm
Blade diameter	190 mm
Blade bore	30 mm
Blade thickness	3 mm
Cutting depth at 90°	65 mm
Cutting depth at 45°	45 mm
Bevel adjustment	0° to 45°
Weight	4.5 kg
Sound pressure level	101 dB(A)
Sound power level	109 dB(A)
Vibration (average value)	< 2.5 m/s²
Insulation	Double insulation (Class II)
Blade guard	Moving guard with riving knife
Supplied accessories	Universal carbide blade, parallel guide, blade wrench, Allen key, dust extraction adapter
Maintenance	No lubrication needed; clean ventilation slots
Warranty	1 year (parts and labor) + 30-day satisfaction guarantee

Frequently Asked Questions - DW365 DEWALT

How to change the blade of the circular saw DW365?

Unplug the tool. Open the blade guard. Turn the blade until you can insert a screwdriver into the blade hole to lock it. Unscrew the screw (8) and the flange (15) counterclockwise using the supplied wrench. Replace the blade following the rotation direction indicated by the arrow. Replace the flange and tighten the screw clockwise.

How to adjust the cutting depth?

Loosen the star knob (3) on the housing. Adjust the base (10) to the desired depth using the graduated scale (4). For a clean cut, let the blade extend about 5 to 8 mm below the workpiece. Tighten the star knob.

How to use the parallel guide?

Insert the parallel guide (6) into the base (10) and tighten the star knob (14). To adjust the width, loosen the knob, position the guide, then retighten. The guide allows straight and parallel cuts.

How to adjust the bevel of the saw?

Loosen the star knob (13) at the back of the saw. Tilt the base (10) to the desired angle (0° to 45°), readable on the graduated scale (12). Retighten the knob.

What are the essential safety instructions?

Always wear safety glasses and a dust mask if necessary. Use rubber gloves and non-slip shoes outdoors. Do not wear loose clothing. Keep children away. Unplug the tool before any adjustment or maintenance. Check that the blade guard works properly.

How to avoid kickback during sawing?

Keep blades sharp. Use a parallel guide for rip cuts. Do not force the tool. Support large pieces near the cut. Immediately release the switch if the blade binds or the motor stalls.

How to maintain the saw DW365?

The tool requires no additional lubrication. Regularly clean the ventilation slots with a soft cloth. Periodically check the condition of the power cord and have it replaced by an authorized service center if damaged.

What types of blades can I use?

Only use saw blades that meet the specifications: diameter 190 mm, bore 30 mm, thickness 3 mm, maximum speed 4,000 rpm. Do not use HSS (high-speed steel) or damaged blades.

How to install the dust extraction adapter?

Mount the adapter (20) onto the nozzle (11) at the rear of the saw. Connect a vacuum cleaner compliant with dust emission regulations. Most vacuum tips fit directly.

What to do if the saw does not start?

Check that the plug is properly connected and that the fuse (10 A) has not blown. Make sure the lock/unlock button (2) is pressed to unlock the switch. If the problem persists, contact an authorized DeWalt service center.

USER MANUAL DW365 DEWALT

F

G

Danish 1

German 7

English 14

Spanish 21

French 28

Italian 34

Dutch 41

Norwegian 47

Portuguese 53

Finnish 59

Swedish 65

Turkish

Greek 78

RUNDSAV DW365

Congratulations!

You have chosen a DEWALT Power Tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional Power Tool users.

Table of contents

Technical data en - 1

EC-Declaration of conformity en - 1

Safety instructions en - 2

Package contents en - 4

Description en - 4

Electrical safety en - 4

Mains plug replacement (U.K. & Ireland only) en - 4

Using an extension cable en - 4

Assembly and adjustment en - 5

Instructions for use en - 5

Maintenance en - 6

Guarantee en - 7

Technical data

		DW365
Voltage V 230
(U.K. & Ireland only) V 230/115
Power input	W 1.350
Power output	W 800
No load speed	min -1	4,000
Bevel setting	up to 45°
Depth of cut at 90°	mm 65
Depth of cut at 45°	mm 45
Blade diameter	mm 190
Blade body thickness	mm 3
Blade bore mm 30
Weight	kg 4.5
Fuses:
Europe	230 V tools	10 Amperes, mains
U.K. & Ireland	230 V tools	13 Amperes, in plugs

The following symbols are used throughout this manual:

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Denotes risk of electric shock.

EC-Declaration of conformity CE

DW365

DeWALT declares that these Power Tools have been designed in compliance with: 89/392/EEC, 89/336/EEC, 73/23/EEC, EN 50144, EN 55104, EN 55014, EN 61000-3-2 & EN 61000-3-3.

For more information, please contact DeWALT at the address below, or refer to the back of the manual.

Level of sound pressure according to 86/188/EEC & 89/392/EEC, measured according to EN 50144:

			DW365
LpA	(sound pressure)	dB(A)*	101
LWA	(acoustic power)	dB(A)	109

* at the operator's ear

Take appropriate measures for the protection of hearing if the sound pressure of 85 dB(A) is exceeded.

Weighted root mean square acceleration value according to EN 50144:

DW365

< 2.5 m/s 2

Director Engineering and Product Development Horst Großmann

When using power tools, always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock, and personal injury. Read the following safety instructions before attempting to operate this product.

Keep these instructions in a safe place!

General

1. Keep work area clean Cluttered areas and benches can cause accidents.

2. Consider work area environment Do not expose power tools to humidity. Keep work area well lit. Do not use power tools in the presence of flammable liquids or gases.

3. Guard against electric shock Prevent body contact with earthed surfaces (e.g., pipes, radiators, cookers, and refrigerators). For use under extreme conditions (e.g., high humidity, when metal swarf is being produced, etc.), electric safety can be improved by inserting an isolating transformer or a (FI) earth-leakage circuit-breaker.

4. Keep children away Do not let children come into contact with the tool or extension cord. Supervision is required for those under 16 years of age.

5. Extension cords for outdoor use When the tool is used outdoors, always use extension cords intended for outdoor use and marked accordingly.

6. Store idle tools When not in use, power tools must be stored in a dry place and locked up securely, out of reach of children.

7. Dress properly Do not wear loose clothing or jewelry. They can be caught in moving parts. Preferably wear rubber gloves and non-slip footwear when working outdoors. Wear protective hair covering to keep long hair out of the way.

8. Wear safety goggles Also use a face or dust mask in case the operations produce dust or flying particles.

9. Beware of maximum sound pressure Take appropriate measures for the protection of hearing if the sound pressure of 85 dB(A) is exceeded.

10. Secure workpiece Use clamps or a vice to hold the workpiece. It is safer and it frees both hands to operate the tool.

11 Do not overreach Keep proper footing and balance at all times.

12 Avoid unintentional starting Do not carry the plugged-in tool with a finger on the switch. Be sure that the switch is released when plugging in.

13 Stay alert Watch what you are doing. Use common sense. Do not operate the tool when you are tired.

14 Disconnect tool Shut off power and wait for the tool to come to a complete standstill before leaving it unattended. Unplug the tool when not in use, before servicing or changing accessories.

15 Remove adjusting keys and wrenches Always check that adjusting keys and wrenches are removed from the tool before operating the tool.

16 Use appropriate tool The intended use is laid down in this instruction manual. Do not force small tools or attachments to do the job of a heavy-duty tool. The tool will do the job better and safer at the rate for which it was intended.

Warning! The use of any accessory or attachment or performance of any operation with this tool, other than those recommended in this instruction manual may present a risk of personal injury.

17 Do not abuse cord Never carry the tool by its cord or pull it to disconnect from the socket. Keep the cord away from heat, oil and sharp edges.

18 Maintain tools with care Keep the tools in good condition and clean for better and safer performance. Follow the instructions for maintenance and changing accessories. Inspect the tool cords at regular intervals and, if damaged, have them repaired by an authorized DeWALT repair agent. Inspect the extension cords periodically and replace them if damaged. Keep all controls dry, clean and free from oil and grease.

19 Check for damaged parts Before using the tool, carefully check it for damage to ensure that it will operate properly

and perform its intended function. Check for misalignment and seizure of moving parts, breakage of parts and any other conditions that may affect its operation. Have damaged guards or other defective parts repaired or replaced as instructed.

Do not use the tool if the switch is defective. Have the switch replaced by an authorized DeWALT repair agent.

20 Have your tool repaired by an authorized DeWALT repair agent

This Power Tool is in accordance with the relevant safety regulations. To avoid danger, electric appliances must only be repaired by qualified technicians.

Additional safety rules for circular saws

Plugging into the mains, switching ON and OFF

• Always ensure that the Power Tool is switched OFF before plugging into the mains.
• Remove the blade changing spanner from the saw blade locking screw before switching ON.
• Do not switch OFF before the saw blade is running freely.

When sawing

• Remove all nails and metal objects from the workpiece before starting work.
• Do not attempt to saw extremely small workpieces.
• After switching OFF, never attempt to stop the saw blade by pressing against the side of the blade.
• Never put the saw down on a table or work bench unless switched OFF.
• Always use the riving knife, except for inserted cuts.

Operational protection devices

• The circular saw must only be used for cutting wood or plastic.
• Ensure that all devices screening the saw blade are in perfect working order.
• Never jam the saw blade guards.
• Free a jammed saw blade guard immediately and do not use the saw if the guard is jammed.
• Do not remove the riving knife.

- The riving knife should be correctly set; the distance between the toothed rim and the riving knife should be 2 mm and the height difference should be 2 mm or less (fig. E).

Checking and changing the saw blade

• Only saw blades conforming to the specifications contained in these operating instructions may be used.
• Saw blades made of high alloy, high speed steel (HSS steel) should not be used. Good results are achieved using carbide-tipped or CrV saw blades.
• Only sharp saw blades in perfect working condition should be used; cracked or bent saw blades should be discarded and replaced at once.
• Ensure that the saw blade is securely fixed and rotates in the correct direction.

Using in a fixed position

• When using a saw bench ensure that the width of the sawing gap is sufficient to take the saw blade being used.
• When cutting narrow workpieces (width less than 80 mm) longitudinally, use a rip fence guide along the longitudinal edge.
• When sawing with the workpiece clamped tight, devices should be used to prevent the workpiece kicking back.
• When sawing circular sections of wood use a device to hold the workpiece steady on both sides of the saw blade to prevent slipping.
• Ensure that pieces of wood sawn off the workpiece cannot be caught up by the teeth of the saw blade and thrown in the air.

Guard against kickback

• Kickback occurs when the saw begins to stall rapidly and is driven back towards the operator. Release the switch immediately if the blade sticks or the saw stalls.
• Keep the saw blades sharp.
• Support large panels near the cutting area.
• Use a fence or straight edge guide when ripping; do not force the tool.
• Do not remove the saw from the work during a cut while the saw blade is rotating. Release the ON/OFF-switch and wait for the saw blade to come to a halt.

Package contents

The package contains:

1 Circular Saw with 1 general purpose TCT blade 1 Parallel fence 1 Saw blade wrench 1 Allen key 1 Dust extraction adapter 1 Instruction manual 1 Exploded drawing

- Check for damage to the tool, parts or accessories which may have occurred during transport.

• Take the time to thoroughly read and understand this manual prior to operation.

Description (fig. A)

Your DEWALT DW365 Circular Saw is a versatile Power Tool designed for professional sawing of wood, wood products and plastics.

1 ON/OFF-switch 2 Lock-off button 3 Star knob for depth of cut 4 Depth of cut scale 5 Guide knob 6 Parallel fence 7 Blade guard 8 Blade bolt 9 Riving knife

10 Saw shoe

11 Dust extraction outlet

12 Bevel scale

13 Star knob for bevel locking system

14 Star knob for parallel fence

15 Outer arbour collar

16 Screw

17 Ventilation slots

Electrical safety

The electric motor has been designed for one voltage only. Always check that the power supply corresponds to the voltage on the rating plate.

Your DEWALT tool is double insulated in accordance with EN 50144; therefore no earth wire is required.

Mains plug replacement (U.K. & Ireland only)

• Should your mains plug need replacing and you are competent to do this, proceed as instructed below. If you are in doubt, contact an authorized DEWALT repair agent or a qualified electrician.
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. Attach the wires to their respective points in the plug (see below). Brown is for Live (L) (2) and Blue is for Neutral (N) (4).
• Before replacing the top cover of the mains plug ensure that the cable restraint (3) is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal screws.

Never use a light socket.

Never connect the live (L) or neutral (N) wires to the earth pin marked E or \(\frac{1}{2}\).

For 115 V units with a power rating exceeding 1500 W, we recommend fitting a plug to BS4343 standard.

Using an extension cable

If an extension cable is required, use an approved extension cable suitable for the power input of this tool (see technical data). The minimum conductor size is \(1.5 \, mm^2\). When using a cable reel, always unwind the cable completely.

Also refer to the table on the next page.

Conductor size (mm2) Cable rating (Amperes)
0.75 6
1.00 10
1.50 15
2.50 20
4.00 25
Cable length (m)
7.5 15 25 30 45 60
Voltage Amperes Cable rating (Amperes)
1	1	5	0	-	2	.	0	6	6	6
		2.1	-	3.4	6	6	6	6	15	15
		3.5	-	5.0	6	6	10	15	20	20
		5.1	-	7.0	10	10	15	20	20	25
		7.1	-	12.0	15	15	20	25	25	-
		12.1	-	20.0	20	20	25	-	-	-
230		0	-	2.0	6	6	6	6	6	6
		2.1	-	3.4	6	6	6	6	6	6
		3.5	-	5.0	6	6	6	6	10	15
		5.1	-	7.0	10	10	10	10	15	15
		7.1	-	12.0	15	15	15	15	20	20
		12.1	-	20.0	20	20	20	20	20	25

Assembly and adjustment

Prior to assembly and adjustment, always unplug the tool.

Depth of cut adjustment (fig. A)

• Loosen the star knob (3) and set the saw shoe (10) to the required position. The adjustment can be read on the scale (4).
• Tighten the star knob.

For optimal results, allow the saw blade to protrude from the workpiece by about 5 - 8 mm.

Mounting and adjusting the parallel fence (fig. B)

The parallel fence is used for cutting parallel to the edge of the workpiece.

Mounting

• Insert the parallel fence (6) in the saw shoe (10) as shown.
• Tighten the star knob (14).

Adjusting

• Slacken the star knob (14) and set the parallel fence (6) to the desired width.
• Tighten the star knob (14).

Bevel adjustment (fig. C)

The bevel angle can be adjusted between 0° and 45°.

• Slacken the star knob (13).
• Set the bevel angle by tilting the saw shoe (10). The angle can be read on the bevel scale (12).
• Tighten the star knob (13).

Removing and installing the saw blade (fig. D)

• Open the blade guard (7).
• Rotate the saw blade until a screwdriver can be inserted into the hole in the blade. This will prevent the blade from rotating while being loosened.
• If no screwdriver is available, or if the saw blade used does not have a hole, lock the blade by pressing the teeth into a piece of wood.
• Loosen and remove the blade bolt (8) and the outer arbour collar (15) by turning the blade bolt counterclockwise using the wrench (18) supplied.
• Replace the saw blade. The teeth must point in the direction of rotation, which is shown by the arrow on the upper guard housing.
• Reinstall the outer arbour collar and firmly tighten the blade bolt by turning clockwise.

Adjusting the riving knife (fig. E)

For the correct adjustment of the riving knife (9), refer to the inset in figure E. Adjust the clearance of the riving knife when the saw blade is changed or whenever necessary.

• Loosen the Allen screws (19) and pull out the riving knife to its maximum length.
• Adjust the clearance and tighten the Allen screws.

Mounting and adjusting the optional guide rail (DE6287) (fig. F)

- Mount your saw onto the 1500 mm guide rail using the screws supplied with the guide rail.

Instructions for use

• Always observe the safety instructions and applicable regulations. - Ensure the material to be sawn is firmly secured in place. - Apply only a gentle pressure to the tool and do not exert side pressure on the saw blade. - Avoid overloading.

Prior to operation:

• Make sure the guards have been mounted correctly. The saw blade guard must be in closed position.
• Make sure the saw blade rotates in the direction of the arrow on the blade.

Switching ON and OFF (fig. A)

For safety reasons the ON/OFF-switch (1) of your Circular Saw is equipped with a lock-off button (2).

• Press the lock-off button (2) to unlock the tool.
• To run the tool, press the ON/OFF switch. As soon as the ON/OFF switch is released, the lock-off button is automatically activated to prevent unintended starting of the tool.

Do not switch the tool ON or OFF when the saw blade touches the workpiece or other materials.

Holding the Circular Saw (fig. A)

• Hold your saw by the main grip and the front handle (5) to guide the saw properly.
• The cut is smoother on the side where the saw blade leaves the workpiece, so clamp the workpiece with the back facing the saw blade.

Dust extraction (fig. G)

Your DEWALT Circular Saw is fitted with a dust extraction outlet (11).

• Mount the dust extraction adaptor (20) to the outlet (11).
• Whenever possible, connect a dust extraction device designed in accordance with the relevant regulations regarding dust emission. Vacuum hoses of most common vacuum cleaners will fit directly into the dust extraction spout.

Using the optional guide rail (fig. F)

The optional guide rail converts your Circular Saw into a convenient, on-site portable alternative for a stationary panel saw. It protects the top layer of your workpiece and allows you to obtain perfectly straight cuts. The bottom of the guide rail is made of anti-slip material.

• Place the guide rail with the saw on the workpiece.
• Guide the saw along the guide rail.

Consult your dealer for further information on the appropriate accessories.

Maintenance

Your DeWALT Power Tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.

Lubrication

Your Power Tool requires no additional lubrication.

Cleaning

Keep the ventilation slots clear and regularly clean the housing with a soft cloth.

Unwanted tools and the environment

Take your tool to an authorized DEWALT repair agent where it will be disposed of in an environmentally safe way.

GUARANTEE

• 30 DAY NO RISK SATISFACTION GUARANTEE •

If you are not completely satisfied with the performance of your DEWALT tool, simply return it within 30 days, complete as purchased, to a participating Dealer, or an authorized DEWALT repair agent, for a full refund or exchange. Proof of purchase must be produced.

• ONE YEAR FREE SERVICE CONTRACT •

If you need maintenance or service for your DEWALT tool, in the 12 months following purchase, it will be undertaken free of charge at an authorized DEWALT repair agent. Proof of purchase must be produced. Includes labour and spare parts for Power Tools. Excludes accessories.

• ONE YEAR FULL WARRANTY •

If your DEWALT product becomes defective due to faulty materials or workmanship within 12 months from the date of purchase, we guarantee to replace all defective parts free of charge or, at our discretion, replace the unit free of charge provided that:

• The product has not been misused. • Repairs have not been attempted by unauthorized persons. • Proof of purchase date is produced. This guarantee is offered as an extra benefit and is additional to consumers' statutory rights.

For the location of your nearest authorized DEWALT repair agent, please use the appropriate telephone number on the back of this manual.

CIRCULAR SAW DW365

Congratulations!

Director Engineering and Product Development Horst Großmann

The packaging contains:

Director Engineering and Product Development Horst Großmann

DEWALT, Richard-Klinger-Straße 40, D-65510, Idstein, Germany

Director Engineering and Product Development Horst Großmann

DEWALT, Richard-Klinger-Straße 40, D-65510, Idstein, Germany

Safety regulations

Director Engineering and Product Development Horst Großmann

DEWALT, Richard-Klinger-Straße 40, D-65510, Idstein, Germany

The parallel fence is used for cutting parallel to the edge of the workpiece.

Assembly

Director Engineering and Product Development Horst Großmann

Director Engineering and Product Development Horst Großmann

X. fopmann

DEWALT, Richard-Klinger-Straße 40, D-65510, Idstein, Germany

Safety instructions