45-361-026 - Flat screen mount Ergotron - Free user manual and instructions

USER MANUAL 45-361-026 Ergotron

Interactive LD LCD Arm

Line drawing of a wall-mounted device with a mounted bracket and mounting plate (no text or symbols)

EN User Guide

ES Guía del usuario

For service and warranty visit www.ergotron.com/warranty

20" (50.8 mm)

70° 5°

	A	B	C	D
1				Wood Stud MountingConcreteø
2	Stud FinderLocalizador de largueros de maderaStud FinderAuswahl von MontagematerialPositiebepaler balkenRilevatore di montantiスタッド ファインダー螺栓探测器ス터드 파인더

	A	B	C	D
1	1x1x 1x	1v
2				1x1x 1xM6 x 45mm
3	1x	4xM4 x 10mm	4x	M8 M5 Kit4xM3x20mm4xM8-M5 Reducer
4	4x1x [1/2"	1xM3 x 6
5	2x	2x[Mi		1x4mm
6	4x 4x 4x M4x12 M5x12 M6x12			1x

1 Mounting Height for Ergonomic Workstation

This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of 5'0"-6'1" (152-185cm) when set up for standing and user heights of 5'0"-6'4" (152-193cm) when set up for sitting.

If user heights are different than this, you should change mounting height to accommodate user heights. (Change mounting height one inch for every one inch difference in user heights).

6" (152 mm)

Mounting height assumes there is a 6" (152 mm) distance between the center of your monitor mounting holes and the top of the screen. If your distance is smaller, you should increase mounting height accordingly, if your distance is larger, you should decrease your mounting height accordingly.

50.5" (1283mm) 5'0" - 6'1" (152.-185cm) 35" (mm) 5'0" - 6'4" (152-193cm)

Determine mounting location:

Front view with arm pushed back against the wall.

10.8" (273mm) 4.3" (107mm) 2.2" (56mm) 8.6" 11.6" (218mm) (295mm)

Top view showing range of motion when pulled out from the wall.

Mechanical lever diagram showing a rotating shaft with two curved arrows indicating rotational motion (no text or labels)

2

Pure mechanical component diagram without any text, numbers, or symbols

3.15" (80mm) 1.57" (40mm) 1.34" (34mm) 6.5" (165mm) 1.14" (29mm) 5.1" (129mm) 7.1" (180mm)

!

CAUTION: Make sure the wall mount bracket is level, flush and snug to the wall surface. DO NOT OVERTIGHTEN THE BOLTS.

Diagram showing a device with a bottle and arrow pointing to an open book labeled '6', likely illustrating a manual or mechanical operation.

Wood

Madera

Bois

(51mm) (102mm) 7

WARNING: Ensure that the wall structure is capable of supporting four times the total weight of mounted equipment. Mounting to wall surfaces that do not meet this criteria may result in an unstable, unsafe condition which could lead to personal injury and/or property damage. Consult a construction professional if you have any doubt about what this means in regard to your particular application.

NOTE: Fasteners may unwind due to vibration caused by movement of mounting solution over time. Inspect mounting solution for loose fasteners on a routine basis. If desired, apply a light duty thread locking adhesive to fasteners before installation to prevent back-out.

4x 10-24 x 5/8" when attaching to Pole Clamps, use 10-24 x 5/8" screws, Do NOT use 10-24 x 1/2" screws 1/8"

When attaching to Pole Clamps, use 10-24 x 5/8" screws included with pole brackets, Do NOT use 10-24 x 1/2" screws

4x 10-24 x 1/2" 1/8"

Wood Stud Mount
2

2" (51mm) 4" (102mm) ≤5/8 (≤16 mm)

a b c

Illustration of hands installing or adjusting a wall-mounted component with a pencil (no text or symbols present)

Illustration of hands installing or adjusting a mechanical component with a tool (no text or symbols visible)

Stud Finder
Localizador de largueros de madera
Stud Finder
Auswahl von Montagematerial

Ø 3/16" (5mm)

Optional locking feature (customer supplied lock)

Line drawing of a handheld device with a hand holding its cable and a close-up view of its internal components (no text or symbols)

3
b

b 2x M8 x 80mm

C

S 13 mm

!
CAUTION: Make sure the wall mount bracket is level, fl ush and snug to the wall surface.
DO NOT OVER- TIGHTEN THE BOLTS.

Concrete Wall Mount

2 a ≤5/8" (≤16 mm) ≥4" (≥102mm) b c 3-1/8" (80 mm) Ø 3/8" (10mm)

WARNING:

Mounting holes must be at least 3-1/8" (80mm) deep and must be located within solid concrete, not mortar or covering material. If you drill into an area of concrete that is not solid, reposition mounting holes until both anchors can be fully inserted into solid concrete!

AVISO:

Anchors that are not fully set in solid concrete will not support the applied load resulting in an unstable, unsafe condition which could lead to personal injury and/or property damage. Consult a construction professional if you have any doubt about what this means in regard to your particular situation.

AVISO:

Optional locking feature (customer supplied lock)

Line drawing of a hand holding a tool with wires, no text or symbols present

C

13 mm

!

CAUTION: Make sure the wall mount bracket is level, fl ush and snug to the wall surface.

DO NOT OVERTIGHTEN THE BOLTS.

4

Mount arm to wall bracket.

b c M6 M6 x 45mm 4mm a NOTE: when sliding sleeve on to bracket, align slot over rota- tion stop. Top View Rotation Stop on Bracket Slot in Sieve Brack

5 Portrait / Landscape Options

OPTION i If you want full 360° portrait/landscape rotation, skip to step 8 on the next page.

OPTION ii If you do not want your TV/Monitor to rotate all all, you can stop rotation by inserting the xx set screw.

6
Check size of TV/Monitor hole pattern
TV/Monitor Hole Pattern Sizes
A
75x75mm 100x100mm

Isometric view of a rectangular block with a central square containing four dots, no text or symbols present.

B
100x200mm

Isometric view of a rectangular block with a shaded internal rectangle and dashed lines indicating hidden edges (no text or symbols)

C
200x200mm

Isometric view of a rectangular block with a central square and dashed inner rectangle (no text or symbols)

D
200x100mm

Isometric view of a rectangular block with a shaded inner rectangle and two marked points (no text or symbols)

VESA Adapter Configurations

100mm (3-15/16") 75mm (2-15/16") 75mm (2-15/16") 100mm (3-15/16"

100mm (3-15/16") 200mm (7-7/8")

200mm (7-7/8") 200mm (7-7/8")

200mm (7-7/8") 100mm (3-15/16")

7 Mount Type A TV/Monitor to Arm

4x

M4 x 10mm

A

75x75mm 100x100mm

100mm (3-15/16") 75mm (2-15/16") 75mm (2-15/16") 100mm (3-15/16"

Technical diagram of a mechanical assembly with two screws and a bracket, showing alignment and assembly details (no text or symbols)

Technical diagram showing assembly of a component with labeled parts and reference lines

M4 x 10mm

8

7 Mount VESA Adapters to Arm based on TV/Monitor hole pattern size (B, C, or D).

Pure mechanical component diagram without any text, numbers, or symbols

Pure mechanical diagram showing a tool interacting with a surface, no text or symbols present

Pure technical diagram of a mechanical component with no text, numbers, or symbols

4x M5 x 7mm

7

Mount Type B, C, or D TV/Monitor to Arm

B 100mm (3-15/16") 200mm (7-78)

C 200mm (7-7/8°) 200mm (7-7/8°)

D 200mm (7-7/8") 100mm (3-15/4)

Technical illustration of a mechanical tool with a screw and two circular holes (no text or symbols)

M4x12 M5x12 M6x12

NOTE: To reduce M8 holes for use with M5 screws, or if you have a model with Samsung holder rings, follow the M8M5 KIT instructions on the next page.

M4x12 M5x12

M6x12

8

M8M5 KIT Instructions

NOTE: follow this step only if your TV/monitor has M8 holes which need to be reduced to M5 or for Samsung models using the holder ring.

Install M8M5 reducer bushing to TV/Monitor and use M5 x 20 mm monitor screws to secure when using the Samsung holder ring.

TV / Monitor Mounting M8 size hole M5x20mm Monitor Screw M8M5 Reducer Bushing Holder Ring (Not Included * Samsung Only)

8 Attach top and bottom bracket covers

Technical line drawing of a mechanical assembly with three directional arrows indicating movement or force (no text or symbols present)

9
Organize and route cables

a 1x 1x b

10

Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.

Warning symbol showing a person holding a pencil with an exclamation mark, indicating caution or hazard.

CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment.

LB kg LB kg 4mm 4mm

CAUTION: DO NOT remove screw. Removing screw may cause damage to equipment.

≥20"508mm

Learn more about ergonomic computer use at: www.ergotron.com/ergonomics

EN For the latest User Installation Guide please visit: www.ergotron.com

For Warranty visit: www.ergotron.com/warranty

For Service visit: www.ergotron.com

For local customer care phone numbers visit: http://contact.ergotron.com

© 2015 Ergotron, Inc. All rights reserved.

While Ergotron, Inc. makes every effort to provide accurate and complete information on the installation and use of its products, it will not be held liable for any editorial errors or omissions (including those made in the process of translation from English to another language), or for incidental, special or consequential damages of any nature resulting from furnishing this instruction and performance of equipment in connection with this instruction. Ergotron, Inc. reserves the right to make changes in the product design and/or product documentation without notification to its users. For the most current product information, or to know if this document is available in languages other than those herein, please contact Ergotron. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written consent of Ergotron, Inc., 1181 Trapp Road, Eagan, Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign. Ergotron is a registered trademark of Ergotron, Inc.