GV-POEX0100 - Unspecified Geovision - Free user manual and instructions

USER MANUAL GV-POEX0100 Geovision

Exterior view of a black GE Uzbekistan network device (no visible text or symbols on body)

Requirements and Limitations

The maximum distance allowed between a PoE switch and a GV-IP Camera depends on the PoE switch type, PoE power output of the connected device (PD) and the type of power supply. These can be summarized as below.

GV-IP Camera Powered by PoE

Brand & ModelPD of GV-IP Camera	GeoVision		Third-Party PoESwitches(IEEE 802.3at)
	GV-POE0801 / 0811GV-POE0812GV-POE1601 / 1611GV-POE2401 / 2411	GV-POE0400GV-POE0410-EGV-POE0800GV-POE0810
PD < 6.49 W(IEEE 802.3af)	600 m (1968.5 ft)	400 m (1312.34 ft)	400 m (1312.34 ft)
PD 6.5 W ~ 12.95 W(IEEE 802.3af)	400 m (1312.34 ft)	200 m (656.17 ft)	200 m (656.17 ft)
PD 13 W ~ 25.5 W(IEEE 802.3at)	200 m (656.17 ft)	-
PD > 25.5 W -	-	-
Note:1. Each GV-POEX0100 extends another 100 m (328.08 ft) between the PoE switch and the GV-IP Camera. Therefore, a distance of 200 m (656.17 ft) requires one GV-POEX0100 and 400 m (1312.34 ft) requires three etc.2. GV-POEX0100 can only be connected using CAT-5e cables, TIA/EIA-568-B, with the maximum DC resistance of 9.38 ohms/100 m.

GV-IP Camera Powered by Power Adapters

Brand & Model	GeoVision		Third-Party PoE Switches (IEEE 802.3at)
	GV-POE0801 / 0811GV-POE0812GV-POE1601 / 1611GV-POE2401 / 2411	GV-POE0400GV-POE0410-EGV-POE0800GV-POE0810
GV-IP Cameras	600 m (1968.5 ft) 400 m	(1312.34 ft) 400 m (1312.34 ft)

Compatibility

1. GV-POEX0100 is only compatible with third-party switches that comply to PoE+ (IEEE 802.3at) and is not compatible with GV-PA191/481/482/901.
2. GV-POEX0100 supports all GV-IP Camera when installed with a power adapter and does not support the following models when powered by PoE:

• GV-BX2510-E / 5310-E
• GV-FE3403 / 5303
• GV-VD2540-E / 5340-E
• GV-SD220 / 220-S

1. GV-POEX0100 is only compatible with the following GeoVision PoE switches of the indicated firmware versions:

• GV-POE0801 / 1601 / 2401 (V1.03 or later)
• GV-POE0811 / 1611 / 2411 (V1.01 or later)

Packing List

1. GV-POEX0100
2. Screw x 2
3. Screw anchor x 2
4. GV-POEX0100 Installation Guide

Overview

GeoVision Prok External 1 2 3

No.	Name Description
1.	PSE Port	Connect to the Power Sourcing Equipment (PSE) or the PoE switch side.
2.	PD Port Connect to	the Powered Device (PD) or the GV-IP Camera side.
3.	DIP Switch	Switch it to ON to enable the PoE function; switch it to OFF to transmit data without supplying the power.

LED indicator:

LED Color/Status Description
PoE	Amber On PoE function enabled
	Off PoE function disabled or no connection
	Green On Ports connected
	Green Blinking Data being transmitted and/or received Data
	Green Off No connection

Setting Up GV-POEX0100

Connect the PSE port of the extender to a power sourcing equipment and the PD port to the powered device using CAT-5e cables. Make sure the DIP switch of every PoE extender is turned to ON to allow for both power and data transmission. This can be illustrated as below:

100 m 100 m 100 m 100 m GV-POE Series PoE Switch ON ON GV-POEX0100 ON GV-IP Camera

Note:

1. Optionally use the supplied screw anchors and screws to fix the extender in place.
2. Make sure the DIP switch of the GV-POEX0100 next to the powered device is turned to OFF for any of the following scenarios:

A. When your camera is powered up with a power adapter and only receives data from the power sourcing equipment. This is illustrated below (though you may use up to 5 extenders).

GV-POE Series PoE Switch 100 m 100 m 100 m 100 m ON ON OFF GV-POEX0100 GV-IP Camera with power adapter

B. When a PoE switch is connected to another PoE or non-PoE switch.

Specifications

For details, see Datasheet.