RK619WALL - Armoire serveur StarTech.com - Free user manual and instructions

USER MANUAL RK619WALL StarTech.com

6U 19in Wall Mount Server Rack Cabinet

Product ID

RK619WALL

Product Diagram

Front - Angled View

3 4 5 3 1 2

Rear - Angled View

d View 6 8 7 5

*Product may vary from image

Component Function
1	Window Area	Enables monitoring of theMounted Equipmentat a glance
2	Door Lock	Locks theDoorusing the included Keys
3	Top and Bottom Vents• Vented panel to promote airflow
4	Cooling Fan	Top-mounted 120mm Fanhelps to regulate the temperature of theMounted Equipment
5	Cable Routing Holes	Removable pre-installed cover. Enables convenient passage for cables
6	Wall-Mounting Holes	Used to fasten theWall-Mounted Rackonto a wallHorizontal distance between theWall-Mounting Holesis 16 in (40.6 cm)
7	Secondary Fan Hole	Removable pre-installed cover. Enables installation of 120mm Fan(not included)
8	Mounting Posts	For mounting 19in Rack Equipment

Product Information

For the latest manuals, product information, technical specifications, and declarations of conformance, please visit: www.StarTech.com/RK619WALL

Requirements

• Phillips Head Screwdriver
- Mounting Hardware (not included)
- Spirit/Bubble Level
• (Optional) Wrench
• (Optional) Cage Nut Tool

How to Identify the LOT Code Revision Number

The Revision Number (Rev #) appears as the fifth and sixth digits of the LOT code, located on the sticker affixed to the product and its packaging. If the LOT code sticker is missing, the product is Rev 01.

Warnings!

• Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product.
  • StarTech.com Ltd. is not responsible for any property damage and/or personal injury resulting from the installation procedures outlined in this technical document.
• Mounting hardware is not included with this product. Make sure to source appropriate mounting hardware that is capable of supporting the weight of a loaded Rack, and is adequate for the wall type the rack is going to be mounted on.
• If you lack the necessary expertise required to attach this product to the wall structure or to assess the suitability of the hardware provided, please contact a professional installer.
• Before adding equipment to this product, ensure this product has been properly mounted.
• Never operate this product if parts are missing or damaged.
• Ensure the weight of the equipment does not exceed the weight capacity of this product. If the weight capacity is exceeded, personal injury or damage to the equipment are possibilities. This product can support the following weight: up to 110.2lbs (50kg).
• Wall structures vary. Ensure the type of wall structure and mounting hardware will properly support the mounted equipment. Failure to do so might result in personal injury and/or equipment damage. The wall structure should be capable of supporting at least four times the weight of the mounted equipment.

Package Contents

• 6U Equipment Rack x 1
• Set of Keys x 1
  • M5 Screws x 20
  • M5 Cage Nuts x 20

Installation

Mount the 6U Equipment Rack to a Mounting Surface

1. Place the 6U Equipment Rack against the Mounting Surface, in the location it will be mounted (ensure it is level, using a Spirit/Bubble Level).
2. Use the Wall-Moutning Holes (x4), located on the Wall Mount Server Rack as a template, and mark the surface in all four locations where the mounting hardware will be installed.
3. Use the appropriate Mounting Hardware to fasten the Wall Mount Server Rack to the Mounting Surface.

Install the Cage Nuts

1. Install the M5 Cage Nuts into the Mounting Holes on the Mounting Posts. If available, use a Cage Nut Tool or your preferred installation method to install the Cage Nuts.
2. Repeat Step 1 as many times as needed to install the number of M5 Cage Nuts required for the application.

3. Align the Mounting Holes on the Rack Equipment with the M5 Cage Nuts installed on the Mounting Posts.

4. Insert the M5 Screws (x 4) through the Mounting Holes (x 4) on the Rack Equipment, and into the M5 Cage Nuts (x 4). Tighten each M5 Screw (x 4) using a Phillips Head Screwdriver to fasten the Rack Equipment to the Mounting Posts.

Reverse the Door

To accommodate different rack configurations, you can reverse the door to open to the left or right of the rack. The door uses spring-loaded pins located at the top and bottom corners of the door.
1. While holding the Door, Pull the Pin Handle Down in the Inside Top Corner of the Door. Pull the Top Corner of the Door slightly away from the Door Frame. (Figure 1)

Two technical illustrations of a cabinet with open doors and arrows indicating force or movement (no text or symbols present)

Figure 1

1. In the Bottom Corner of the Inside of the Door, Pull the Pin Handle Up and remove the Door. Retain the Washer from the Bottom Corner, for re-installation of the Door. The Washer may be located on the Pin or the Lower Hinge Hole on the Door Frame (Figure 2).

Technical illustration of two open industrial cabinets with blue arrows indicating movement, showing internal components and a magnified detail (no text or symbols)

Figure 2

1. Re-orientate the Door so that the Pins are located on the Opposite Side, with the Front of the Door Facing Outwards. (Figure 3)

Diagram of a closed storage cabinet with an open door and lid, showing internal components and airflow direction (no text or symbols)

Figure 3

1. Install the Washer (retained in Step 2) onto the Bottom Pin on the Lower Inside Corner of the Door. (Figure 4)

Simple line drawing of a mechanical component with a blue arrow pointing to a circular feature (no text or symbols)

Figure 4

1. With the top corner of the door angled slightly away from the enclosure, gently Insert the Bottom Pin, ensuring is Fully Extended into the Washer and the Lower Hinge Hole. (Figure 5)

Simple line drawing of a mechanical assembly or bracket (no text or symbols)

Figure 5

1. With the Bottom Pin partially installed, Pull the Top Pin Handle Down and swing the Top Corner of the Door toward the Upper Hinge Hole. Align the Retracted Top Pin with the Upper Hinge Hole and Release the Pin Handle, ensuring the Pin is Fully Extended into the Upper Hinge Hole. (Figure 6)

Diagram of a cabinet with open door and air vent, showing internal components and airflow direction (no text or symbols)

Figure 6

Regulatory Compliance

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders. PHILLIPS ^® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

This product is backed by a lifetime warranty.

For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

NL: startech.com/nl IT: startech.com/it

1. startech.com/it IP: startech.com/in