99-6520B - Kit d'installation audio AXESS - Free user manual and instructions

USER MANUAL 99-6520B AXESS

Interior view of a car dashboard with touchscreen and control panel (no visible text or symbols)

Dodge Journey 2011-2020

Visit NetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications.

KIT FEATURES

• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Included interface retains factory screen
• Painted matte black to match factory finish

Note: · Does not retain sound from Driver Convenience Group.

- Track and launch control features from SRT Package will be lost.

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) A/C button housing • D) Pocket • E) Console bracket • F) #8 x 3/8" Phillips pan-head screws (6)
• G) Panel clips (2) • H) Climate extension harness (not shown) • I) Axxess interface and harness (not shown)

A

Technical line drawing of a mechanical bracket or housing component (no text or symbols)

B

Technical line drawing of two mechanical bracket components (no text or symbols)

• 

E

F

G

TABLE OF CONTENTS

Dash Disassembly 2-3

Kit Preparation....4

Kit Assembly

• ISO DIN radio provision with pocket.....5
• ISO DDIN radio provision ....5
  Axxess interface installation 6-12

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Interface and harnesses included Antenna Adapter: 40-EU10 (sold separately) AXXESS Steering Wheel Control Interface (sold separately)

TOOLS REQUIRED

- Panel removal tool • Phillips screwdriver

ATTENTION: With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections, especially the air bag indicator light, must be secure before cycling the ignition to test this product. NOTE: Refer also to the instructions included with the aftermarket radio.

DASH DISASSEMBLY

1. Using the panel removal tool, carefully unclip and remove the trim panel along the top of the glove box over to the passenger's side A/C vent. (Figure A)
2. Unsnap and remove the small trim panel to the left of the hazard button. (Figure A)
3. Remove (2) Phillips screws securing the radio/climate control panel, then unclip, unplug and remove the panel. (Figure B) Note: A climate extension harness is provided to relocate the climate controls to a lower position in the center console.
4. Remove (4) Phillips screws securing the radio chassis. Slide the chassis out, then unplug and remove the chassis. (Figure C) Note: The white 4-pin harness will be reused in Kit Assembly.

Continued on the next page

Line drawing of a car dashboard with control panel and directional arrows indicating traffic flow (no text or symbols)

(Figure A)

Line drawing of a car head panel with directional arrows indicating traffic flow (no text or symbols)

(Figure B)

Technical line drawing of a vehicle's internal components, showing structural parts and mounting brackets (no text or symbols)

(Figure C) (Figure D)

Line drawing of an electronic device rear panel with internal components and a button (no text or symbols)

DASH DISASSEMBLY (CONT)

1. Pull up on shift knob to remove. (Figure D).
2. Unclip and remove the shifter trim panel, including the cup holders from the top of the center console. (Figure E)
3. Push down and then pull back and out on the pocket in the front of the console. (Figure F)

Note: You may need to pull the console side panels outward at the same time as pulling out on pocket.

1. Remove the (2) metal panel clips on the front side of the pocket and save for Kit Preparation.

Line drawing of a car gear shift lever with an arrow indicating upward motion (no text or symbols)

(Figure D) (Figure F)(Figure E)

Diagram of a car interior showing intake manifold and exhaust slots with directional arrows (no text or labels)

Line drawing of a car interior compartment with directional arrows indicating movement or flow (no text or symbols)

Continue to Kit Preparation

KIT PREPARATION

1. Attach the console bracket to the back of the A/C button housing using (4) #8 x 3/8" Phillips screws provided with this kit. (Figure A)
2. Install the (2) metal panel clips saved from the pocket disassembly onto the console bracket. (Figure A)
3. Using the climate extension harness provided with this kit, connect the A/C button housing assembly to the factory wiring harness in the vehicle.
4. Secure the A/C button housing into the pocket space in the front of the center console. (Figure B)

Technical line drawing of a mechanical component with no visible text or symbols

(Figure A) (Figure B)

Line drawing of a vehicle's seatbelt with surrounding gear and dashboard (no text or symbols)

Continue to Kit Assembly

KIT ASSE MB LY

ISO DIN radio provision with pocket

1. Secure the radio brackets to the pocket using the (2) #8 x 3/8" Phillips screws provided with this kit. (Figure A) Note: Pins on the brackets will align with the front mounting hole of pocket.
2. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
3. Slide the radio into the bracket/pocket assembly, then secure it to the assembly using the screws supplied with the radio. (Figure B)

Continue to Axxess Interface Installation

Technical line drawing of a mechanical housing or enclosure component (no text or symbols)

(Figure A) (Figure A)

Technical line drawing of a mechanical device with no visible text or symbols

(Figure B)

ISO DDIN radio provision

1. Break the small locating pin from the inside surface of each bracket. (Figure A)
2. Secure the radio brackets to the radio using the screws supplied with the radio. (Figure A)

Continue to Axxess Interface Installation

Remove pin

Technical line drawing of a device with labeled ports and connectors (no text or symbols present)

(Figure B)

AXXESS INTERFACE INSTALLATION

INTERFACE FEATURES TABLE OF CONTENTS

• Provides accessory power (12-volt 10-amp)
  • Retains R.A.P. (retained accessory power)
  • Used in amplified and non-amplified systems
• Provides NAV outputs (parking brake, reverse, V.S.S.)
• Prewired for an AXXESS steering wheel control interface
• Retains balance and fade
• Ability to add an aftermarket backup camera or additional video input
• Retains the factory display screen
• Micro "B" USB updatable

Note: Does not retain sound from "Driver Convenience Group"

Connections....7
Installation 8
Programming......8
Final Assembly 8
Audio Level Adjustment 8
Screen Operation 9-11
Updating The Interface ....12

INTERFACE COMPONENTS

• Axxess interface
  • 16-pin harness with stripped leads
  • 6520 harness

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder, and heat shrink
• Tape • Wire cutter • Zip ties • Small flat-blade screwdriver

CONNECTIONS

From the 16-pin harness with stripped leads to the aftermarket radio, connect as indicated:

• Red wire to the accessory wire.
Note: If also installing an AXXESS steering wheel control interface (sold separately, there will be a Red wire on the 6520 harness to connect as well.
- Orange/White wire to the illumination wire, if applicable.
- Blue/White wire to the amp turn-on wire, if equipped with a factory amplifier.

The following (3) wires are for aftermarket multimedia/navigation radios that require these wires:

• Blue/Pink wire to the speed sense wire.
• Green/Purple wire to the reverse wire.
• Light Green wire to the parking brake wire.

Tape off and disregard the following (9) wires, they will not be used in this application:

Brown, White, White/Black, Gray, Gray/Black, Purple, Purple/Black, Green, Green/Black.

From the 6520 harness to the aftermarket radio, connect as indicated:

• Black wire to the ground wire.
• Yellow wire from both the 6520 harness and the loose yellow wire coming from the HVAC controller to the battery wire.
• Gray wire to the right front (+) speaker output.
• Gray/Black wire to the right front (-) speaker output.
• White wire to the left front (+) speaker output.
• White/Black wire to the left front (-) speaker output.
• Green wire to the left rear (+) speaker output.

From the 6520 harness continued...

• Green/Black wire to the left rear (-) speaker output.
  • Purple wire to the right rear (+) speaker output.
  • Purple/Black wire to the right rear (-) speaker output.
• Yellow RCA jack labeled (2) to either an aftermarket backup camera, or an AUX video input.

Disregard the Yellow RCA jack labeled (1), it will not be used in this application.

Note: There is also a set of Green, Green/Black, Violet, Violet/Black wires coming from the Black 18-pin connector that goes to the interface, tape off and disregard these wires, they will not be used in this application.

From the 12-pin 6520 harness connector:

• If the vehicle is not equipped with steering wheel controls, disregard this connector entirely.
• If the vehicle has steering wheel controls, the 12-pin 6520 connector is to be used along with the optional AXXESS steering wheel control interface (sold separately) to retain steering wheel controls.
• Attach the 12-pin connector from the 6520 harness to the AXXESS steering wheel control interface (sold separately).

Note: Disregard the harness that comes with the AXXESS steering wheel control interface.

Note: Please verify AXXESS steering wheel control interface connections for your vehicle by visiting www.axxessinterfaces.com, and using the vehicle fit guide to find a vehicle specific instruction.

INSTALLATION FINAL ASSEMB

Attention! For models with a 8-inch screen, update the interface via the Axxess Updater available at axxessinterfaces.com. Select "8-inch screen" once prompted to. Instructions to update the interface are available at the end of this instruction booklet.

With the key in the off position:

1. Connect the 16-pin harness with stripped leads, and the 6520 harness, into the interface.
2. Connect the factory "White" 4-pin harness removed in step 4 of Dash Disassembly to the "Black" connector from the interface.

Note: The display screen will not function without this connection.

1. Connect the 6520 harness to the wiring harness in the vehicle.
2. Locate the factory antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra.

Note: If an AXXESS steering wheel control interface (sold separately) will be used, do not connect it until the interface is programmed and fully functional.

PROGRAMMING

1. When the interface first boots up, the factory screen will go through a boot up sequence for a few moments. Do not touch any controls during this process.

2. Test all functions of the installation for proper operation, before reassembling the dash. For amplified models, also refer to the "Audio Level Adjustment" section.

3. Secure the completed assembly to the dash using the factory hardware.

4. Attach the (2) panel clips provided to the 99-6520B radio trim panel, then reassemble the dash in reverse order of disassembly using the 99-6520B panel.

AUDIO LEVEL ADJUSTMENT

For models with a factory amplifier:

1. With the vehicle and radio turned on, turn the volume up 3/4 of the way.
2. With a small flat-blade screwdriver, adjust the potentiometer clockwise to raise the audio level; counterclockwise to lower the audio level.
3. Once at a desired level, audio level adjustment is complete.

Diagram of a car air conditioner panel with labeled buttons and function icons

1. Radio button – Show the current time
2. Player button – Not used in this application
3. Climate button – Takes you to the climate screen
4. Setting button - Takes you to the setting screen
5. More button – Shows the outside temperature and current time
6. Screen Off – Turns the display off

FACTORY 4.3 INCH SCREEN VIDEO OPTIONS MENU

1. Once in the setting screen, scroll down to the Customize button. Pressing the button will take you to the video option screen. (Figure A)
2. Once in the customize menu, you can select to make the Video Input 2 either: (Figure B)

Please select a setting: Settings Doors & Locks Engine off options Customize

(Figure A) (Figure C)

• Not Used
• Back-up (Backup Camera) is controlled by data and will only activate when you put the vehicle in reverse.

• AUX input is controlled by data and will only work while the vehicle is in park. (Figure C)

• After you have made your selection, tap the "Done" button located on the upper left hand corner of the screen to exit.

• The About button will display the current software of the kit, and also the VIN of the vehicle. (Figure D)

Done Video Input Line #2 BACK-UP AUX NOT USED Camera selection will turn on when in Reverse. Use the "PLAYER" button to cycle through the Climate and active Video screen(s) manually.

About... Version: B21

Customize Video Input #1 Video Input #2 About... Please select a setting:

(Figure B) (Figure D)

1. Enter the settings menu by tapping the gear icon in the upper left corner of the screen.

Settings Lights > Doors & Locks > Engine Off Options > Auto-On Comfort & Remote Start > Compress > Customize >

1. Once in the setting menu, scroll down and tap the Customize button to enter the customize menu.

Settings>Customize Video Input 2 Not Used Play Aux About

1. Once in the customize menu, you can select to make the Video Input 2 either:

2. Not Used

3. Reverse (Backup Camera) is controlled by data and will only activate when you put the vehicle in reverse.
4. AUX input is controlled by data and will only work while the vehicle is in park.

Settings>Customize Video Input 2 About Release: 1.00 A: 1.00 B: NONE C: 1.00F D: T: 1.00 Win OK

1. Tapping the About button will display the current version number of the kit, and the VIN number of the vehicle. Tap the OK button to exit.
2. After you have made your selection, tap either the X or Back (left arrow) button one time to return to the previous menu, or two times to return to the main menu.

UPDATING THE INTERFACE

• Download and install the Axxess Updater from axxessinterfaces.com.
• Connect the USB-MINI-CAB update cable (sold separately) between the interface and the computer. The cable will connect into the Micro-B USB port inside the interface.
• From the Start Menu of the computer, click on "Axxess Updater", and then click "Update Firmware". The interface will begin to update at this point.

Note: Please note which firmware downloaded to the interface. This will help in troubleshooting, if need be.

Having difficulties? We're here to help.

our Tech Support line at:

386-257-1187

mail at:

[e-mail]

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM

Saturday: 10:00 AM - 5:00 PM

Sunday: 10:00 AM - 4:00 PM

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills to enrolling in the most recognized and respected

enrolling in the most recognized and resp mobile electronics school in our industry.

Log onto www.installerinstitute.edu or call

386-672-5771 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Interior view of a car dashboard with a central touchscreen display and control panel (no visible text or symbols)

Dodge Journey 2011-2020

Technical line drawing of a mechanical bracket or housing (no text or symbols)

B

Technical line drawing of two mechanical components with mounting brackets (no text or symbols)

• 

• 

F

G

INDICE

Line drawing of a car head panel with directional arrows indicating movement or flow (no text or symbols)

(Figure A)

Diagram of car dashboard and rear panel showing engine compartment with arrows indicating direction (no text or symbols)

(Figura B)

Technical line drawing of a vehicle's internal components, showing brackets and mounting points (no text or symbols)

(Figura C) (Figura D)

Line drawing of a mechanical device casing with internal components and mounting holes (no text or symbols)

DESMONTAJE DEL TABLERO (CONT)

Line drawing of a car gear shift lever with an arrow indicating upward motion (no text or symbols)

(Figura D) (Figura F)(Figura E)

Diagram of a car interior showing gear shift and directional arrows (no text or symbols)

Line drawing of a car interior compartment with arrows indicating movement or flow (no text or symbols)

Technical line drawing of a mechanical component with no visible text or symbols

(Figura A) (Figura B)

Line drawing of a vehicle's seatbelt with surrounding gear and dashboard (no text or symbols)

Technical line drawing of a mechanical housing or enclosure component (no text or symbols)

(Figura A) (Figura A)

Technical line drawing of a mechanical device with no visible text or symbols

(Figura B)

Technical line drawing of a device with labeled ports and connectors (no text or symbols present)

(Figura B)

Diagram of a car air conditioner panel with labeled buttons and function icons

Please select a setting: Settings Doors & Locks Engine off options Customize

(Figura A) (Figura C)

Done Video Input Line #2 BACK-UP AUX NOT USED Camera selection will turn on when in Reverse. Use the "PLAYER" button to cycle through the Climate and active Video presentation manually.

Customize Video Input #1 Video Input #2 About... Please select a setting:

(Figura B) (Figura D)

About... Version: B21

Settings>Customize Video Input 2 Release: 1.00 A: 1.00 B: NONE C: 1.00# D: 1.00# E: 5.00# F: 5.00# Vin: OK

Certification Program, MECP).