KADSTV65NBA - TV Kogan - Free user manual and instructions

USER MANUAL KADSTV65NBA Kogan

Line drawing of a four-legged stool with two vertical posts and a flat base (no text or symbols)

DANISH STYLE TV FLOOR STAND WITH STORAGE SHELF

(MATTE BLACK & WALNUT, SUITABLE FOR 43-65" TVS)

KADSTV65NBA

SAFETY & WARNINGS

Read the entire user guide before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, contact your local distributor for assistance.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
• Safety gear and proper tools must be used. This product should only be installed by professionals.
• This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• Never exceed the maximum load capacity of 40kg or it may result in product failure or personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact your place of purchase for a replacement.

MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

VESA Compatible 100x100 200x100 200x200 300x200 400x200 300x300 400x300 400x400 65" MAX TV RATED 40kg/88lbs SHELF RATED 10kg/22lbs

COMPONENTS

Technical line drawing of a mechanical bracket with mounting holes and mounting holes (no text or symbols)

A TV shelf (x1)

D TV Brackets (x2)

G Cable Guides (x4)

J M6x12 Screw (x4)

M M8x12 Screw (x2)

P Open Spanner 13mm

P-C Bracket (x1)

P-F Wall Anchor (x1)

Simple line drawing of a rectangular metal plate with two small holes (no text or symbols)

A Shelf (x1)

E Foam Pad (x1)

Line drawing of a metal bracket with two holes and a slot (no text or symbols)

H Leg Bracket (x4)

K M8x16 Screw (x4)

N M8x30 Screw (x2)

P-A Safety Wire

P-D (x2)

P-G D5 Washer (x2)

C Legs (x4)

F Foam Pad (x1)

I M8 Nut (x2)

L ST4.2x12 Screw (x4)

• Allen Key 5mm
  
  P-B Bracket (x2)

P-E ST4.8x38 Screw (x1)

M-A M6x35 Screw (x4)

M-B M6x45 Screw (x4)

M-C M8x35 Screw (x4)

M-D M8x50 Screw (x4)

M-E D8 Washer (x4)

M-F Spacer (x8)

M-G Spacer (x8)

Tools Required

Stud finder

Pen/pencil

Drill & Drill Bit

Phillips head screwdriver

Safety Disclaimer

This product includes essential safety kits that must be used with the product to prevent it from falling or tipping over. Follow the enclosed instructions carefully to correctly install these safety accessories. Kogan.com shall not be liable for any direct, indirect, punitive, incidental, or special consequential damages to property or life arising out of or connected with the use or misuse of this product.

ASSEMBLY

Step 1:

• Attach the legs to the TV Shelf (A) and secure it in place using x4 M8x16 Screws (K).
• Peel the adhesive backing and attach the Foam Pads (E) & (F) to the TV shelf.

Technical diagram showing mechanical assembly with labeled parts (A, C, K) and a magnified inset of a hand holding a component labeled E and F.

Step 2: Attach the x4 Brackets (H) to the Shelf (B) and secure it in place using x4 M6x12 Screws (J).

Note: Leave at 2mm gap before the screw and the bracket.

2mm G B J H

Step 3: Attach the Shelf (B) to the Legs and secure it in place using x4 ST4.2x12 Screws (L).

Note: After tightening the 4 self-tapping screws, tighten the 2 screws in each plate as shown

Adjust the metal plates to align the holes in the wooden legs ① ② L 2mm

Step 4: Loosen the fasteners and adjust the length of the TV brackets (D) to your desired height. Note: Ensure the fasteners are retightened before proceeding.

Technical diagram of a mechanical clamp or bracket assembly with labeled parts D and P, showing internal components and rotation arrows.

Step 5: Attach the TV brackets (D) to the assembly using x2 M8x30 Screws (N), x2 M8x12 screws (M) and x2 M8 Nuts (I). Note: Ensure the fasteners are properly tightened before proceeding.

Technical line drawing of a mechanical support structure with mounting holes and mounting feet (no text or symbols)

Technical diagram showing mechanical assembly with labeled parts M and N, including a rotation arrow and directional arrows.

Step 6:

• Align the brackets (D) with the TV's VESA upper holes and secure using supplied screws ("M-" set), Safety Brackets (P-B) Washers (M-E) and spacers (M-F, M-G) depending on required length.
• Align the brackets (D) with your TV's VESA lower holes and secure using supplied screws ("M-" set), Washer (M-E) and spacers (M-F, M-G) depending on required length.

Note: The TV should be resting on foam pads (E, F).

Technical diagram showing four types of mechanical fasteners with checkmark and various assembly configurations

X Too long Too Short

TOP M-GM-F M-E P-B M-A M-GM-F M-E P-B M-B M-GM-F M-E P-B M-D M-GM-F M-E M-A M-GM-F M-E M-B M-GM-F M-E M-D

Step 7:

• Peel the adhesive backing and attach the Cable Guides (G) to the assembly.
• Route the TV cables down the frame legs and secure them in place with the Cable Guides.

Technical line drawing of a simple chair with vertical supports and a cable, showing structural details and a magnified inset of hand using a tool (no text or symbols present)

Step 8:

• To avoid the TV falling, it is highly recommended to install the anti-fall hardware.
• Mark the desired position for the anti-fall bracket (P-C). For drywall or plaster, use a stud finder.
• Drywall / plaster: Drill a pilot hole using a 3.5mm drill bit and drill.
• Masonry / concrete: Drill a pilot hole using a 7mm drill bit and drill.

P-C 950-1250mm 40mm (1.6") Ø 3,5mm (Ø 1/8")

P-C 950-1250mm 40mm (1.6") Ø 7mm (Ø 9/32")

Step 9:

- Drywall / plaster: Secure the anti-fall bracket (P-C) to the wall using the ST4.8x38 screw (P-E).

- Masonry / concrete: Secure the anti-fall bracket (P-C) to the wall using the wall anchor (P-F) and ST4.8x38 screw (P-E).

Step 10:

Using the anti-fall rope (P-A), x2 cable clips (P-B) and x2 rope screws (P-D) secure the TV to the wall.

Note: Ensure there is enough tension on the rope so that the TV will not tip over.

Line drawing of a large screen mounted on an easel with a suspended object, no text or symbols present

P-A P-B P-D

NOTES

Need more information?

We hope that this user guide has given you the assistance needed for a simple set-up.

For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

kogan.com