KAARTV65NBA - TV Kogan - Free user manual and instructions
Find the device manual for free KAARTV65NBA Kogan in PDF.
User questions about KAARTV65NBA Kogan
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your TV in PDF format for free! Find your manual KAARTV65NBA - Kogan and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. KAARTV65NBA by Kogan.
USER MANUAL KAARTV65NBA Kogan
natural_image
Line drawing of a three-legged stand with a cylindrical top and two horizontal plates (no text or symbols)ARTISTIC SOLID WOOD FLOOR STAND WITH SHELF
SUITABLE FOR 45"-65" TVS
KAARTV65NBA
SAFETY & WARNINGS
- Failure to read, thoroughly understand and follow all instructions can result in serious personal injury or property damage. If you have any questions regarding any of the instructions or warnings, contact help.Kogan.com for support.
- Ensure that the mounting surface is strong enough to handle a mounted product and equipment.
• DO NOT EXCEED THE MAXIMUM LISTED WEIGHT CAPACITY.
• Always use an assistant or a mechanical lifting device to safely lift and position heavy products.
- Tighten screws firmly, but do not over tighten. Over tightening can cause product damage that greatly reduces the holding power.
- Keep a clear area and distance from moving parts when using the product.
- Use only as intended. Never stand, hang or climb on the product.
- This product is intended for indoor use only. Any attempts to reconstruct the product are not permitted. This product may contain small items that could be a choking hazard if swallowed. Keep children away unless the product is intended for their use and all instructions are fully reviewed and understood by them.
- Check that the product is secure and safe to use at regular intervals (at least every three months).
- This product includes safety kits that must be used in conjunction with the product to prevent the product from falling or tipping over. Follow the enclosed information to properly install these safety accessories.
VESA Compatible 200x200 300x200 400x200 300x300 400x300 400x400



COMPONENTS
![]() | ![]() | ![]() | ![]() |
| A Shelf (x1) | B Upper bracket (x1) | C Lower bracket (x1) | D Stand (x1) |
![]() | ![]() | ![]() | ![]() |
| E Rear Leg (x1) | F Front Leg (x2) | G Locking Collar (x1) | H Cable Clips (x2) |
![]() | ![]() | ![]() | ![]() |
| I ST4.2x12 Screw (x2) | J M6x30 Screw (x4) | K M6x60 Screw (x1) | L M6x90 Screw (x1) |
![]() | ![]() | ![]() | ![]() |
| M 4x120mm Allen Key (x1) | M-A M6x14 Screw (x4) | M-B M8x16 Screw (x4) | M-C M6x30 Screw (x4) |
![]() | ![]() | ![]() | ![]() |
| M-D M8x35 Screw (x4) | M-E D8 Washer (x4) | M-F 15 8 5 Spacer (x4) | M-G 15 8 5 Spacer (x4) |
![]() | ![]() | ![]() | ![]() |
| P-A Anti-fall Rope (x1) | P-B Cable Clips (x2) | P-C Anti-fall Bracket (x1) | P-D Rope Screw (x2) |
![]() | ![]() | ![]() | |
![]() | P-F 7x35 Wall Anchor (x1) | P-G D5 Washer (x2) |
ASSEMBLY
Step 1:
![]() | ![]() | ![]() | ![]() | ![]() |
Using the Allen key (M), secure the shelf (A) to the stand (D) using the M6x60 screw (K) and x2 M6x30 screws (J).

text_image
Technical diagram of a mechanical device with labeled components and control panel symbolsStep 2:
- Using the Allen key (M), secure the front legs (F) to the shelf (A) using x2 M6x30 screws (J).
- Using the Allen key (M), secure the rear leg (E) to the shelf (A) using the M6x90 screw (L).

text_image
Technical diagram of a mechanical assembly with labeled parts E, F, J, and L, showing exploded view of components.Step 3:

natural_image
Simple line drawing of a mechanical component resembling a bell or taper (no text or symbols)- Using the Allen key (M), loosen the screw on the locking collar (G). Move the locking collar (G) into the required position and tighten the screw using the Allen key (M).
- Secure the locking collar (G) before attaching the TV.
- Ensure the screw hole is facing the back.

text_image
Recommended 50-400mm
text_image
Diagram illustrating three-step mechanical assembly steps with arrows indicating rotation and adjustment.Step 4:
Loosen the screw on the lower bracket (C) to open the clasp.

text_image
Diagram illustrating a mechanical assembly process with labeled parts and directional arrows indicating motion or transformation.Step 5:
- Attach the brackets (B & C) to the rear of the TV and secure them in place using the supplied screws ('M-' set) and washers (M-E).
- The x2 cable clips (P-B) must be attached to the upper bracket (B).
- Note: Depending on your TV you may need to install the spacers (M-F & M-G).

text_image
M-A M-B P-B M-E M-C M-D P-B M-E M-F M-G B TOP Too Long Too Short M-A M-B M-C M-D M-E M-F M-G
text_image
× Too Long Too Short × ✓
text_image
Diagram illustrating a mechanical or electrical setup with labeled components and directional arrows indicating motion or rotation.
text_image
M-A M-B M-E M-C M-D M-E M-F M-GStep 6:

natural_image
Two simple icons: one with a 2+ symbol and the other a shaded mountain shape (no text or symbols)- Carefully attach the TV to the stand. Enlist the help of a second person to safely carry the TV.
- Close the clasp on the lower bracket (C) and tighten the screw.

natural_image
Line drawing of a three-legged stand with a vertical support structure, mounted on a tripod (no text or symbols)
natural_image
Mechanical assembly diagram showing a vertical rod inserted into a bracket with a downward arrow indicating force or direction (no text or symbols present)
natural_image
Technical line drawing of a mechanical assembly with no visible text or symbols
natural_image
Mechanical diagram showing a rotating component with a screwdriver, no text or symbols present
text_image
Diagram illustrating a screwdriver mechanism with labeled parts H and I, showing motion direction and rotation.Attach the x2 cable clips (H) to the TV stand using the x2 ST4.2x12 screws (I). Then, route the cable.
Step 7:
• To avoid the TV falling, it is highly recommended to install the anti-fall hardware.
- Mark the desired position for the anti-fall bracket (P-C). For drywall or plaster, use a stud finder.
- Drywall / plaster: Drill a pilot hole using a 3.5mm drill bit and drill.
- Masonry / concrete: Drill a pilot hole using a 7mm drill bit and drill.

text_image
800-1100mm P-C
text_image
P-C 800-1100mm
text_image
Ø3.5mm (Ø1/8") 40mm (1.6")
text_image
Ø7mm (Ø9/32") 40mm (1.6")Step 8:
- Drywall / plaster: Secure the anti-fall bracket (P-C) to the wall using the ST4.8x38 screw (P-E).
- Masonry / concrete: Secure the anti-fall bracket (P-C) to the wall using the wall anchor (P-F) and ST4.8x38 screw (P-E).

Step 9:
Using the anti-fall rope (P-A), x2 cable clips (P-B) and x2 rope screws (P-D) secure the TV to the wall.
Note: Ensure there is enough tension on the rope so that the TV will not tip over.

text_image
P-A P-DNOTES
Need more information?
We hope that this user guide has given you the assistance needed for a simple set-up.
For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com
kogan.com
































