99-8164T - Kit d'installation audio voiture AXESS - Free user manual and instructions

USER MANUAL 99-8164T AXESS

Interior view of a car dashboard with digital displays and instrument gauges (no visible text or symbols)

Lexus RX300 (US model vehicles only) 1999-2003

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications

KIT FEATURES

• ISO DDIN radio provision
  • ISO DIN radio provision with pocket
• Custom texture and painted tan or gray to match the factory appearance
• Touchscreen for retention of climate control functions
• Factory amplifier not retained with this product - an amplifier bypass harness is included
  • 99-8164T — Tan w/black trim, 99-8164G — Gray w/black trim

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) Panel clips (3) • E) #8 x 3/8" Pan-head Philips screws (8)
  • F) Wiring and interfacing (not shown)

Technical line drawing of a mechanical device with no visible text or symbols

Two mechanical clamps with mounting holes and mounting brackets, shown in line drawing without any text or symbols.

Isometric line drawing of a rectangular electronic enclosure or housing with mounting holes (no text or symbols)

TABLE OF CONTENTS

Dash Disassembly 2
Kit Preparation....3
Kit Assembly 4
Axxess Interface Installation 5-11
Final Assembly 9

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Included with kit

Antenna Adapter: Not needed

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver
• 10mm Socket wrench

Attention! With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product.

DASH DISASSEMBLY

1. Unsnap and remove the shifter trim. (Figure A)
2. Remove (4) 10mm bolts and remove the radio assembly. (Figure B)

Interior view of a car headset showing dashboard, steering wheel, and gear shift (no text or symbols)

(Figure A) (Figure C)

1. Depress side tabs to remove the factory hazard button and passenger airbag light from the factory radio assembly. (Figure C)
2. Depress all four side tabs to remove the factory vents from the factory radio assembly. (Figure D)

Continue to Kit Preparation

Line drawing of a car air conditioning device with control panel and indicator lights (no text or symbols)

Line drawing of a vintage electronic device with control panel and display screen (no text or symbols)

Top-down schematic of a vehicle dashboard with front, rear, and side panels (no text or symbols)

(Figure B) (Figure D)

KIT PREPARATION

1. Attach the (3) supplied panel clips to the radio trim panel. (Figure A)
2. Snap the passenger airbag light and hazard button into the radio trim panel from the back. (Figure B)
3. Attach the factory vents to the radio trim panel (Figure C)

Continue to Kit Assembly

Technical line drawing of a mechanical device with mounting brackets and control panel (no text or symbols)

(Figure A)

Technical line drawing of a vehicle chassis with attached sensors and control panel (no text or symbols)

(Figure B) (Figure C)

Technical line drawing of a mechanical device with three labeled components (no text or symbols present)

KITASSEMBLY

ISO-DIN radio provision with pocket

1. Secure the pocket to the radio brackets using the (4) #8 x 3/8" Phillips screws supplied. (Figure A)
2. Attach the radio bracket/pocket assembly to the radio using screws supplied with the radio. (Figure B)
3. Attach the completed assembly to the radio trim panel using the supplied (4) #8 x 3/8" Phillips screws. (Figure C)

Continue to Axxess Interface Installation

Technical line drawing of a mechanical bracket assembly (no text or symbols)

(Figure A)

Technical line drawing of a device housing with mounting holes and ventilation slots (no text or symbols)

(Figure B)

Technical line drawing of a mechanical device with internal components and alignment lines (no text or symbols)

(Figure C)

ISO-DDIN radio provision

1. Secure the radio brackets to the radio using screws supplied with the radio. (Figure A)
2. Attach the completed assembly to the radio trim panel using the supplied (4) #8 x 3/8" Phillips screws. (Figure B)

Continue to Axxess Interface Installation

Technical diagram of an electronic device with labeled ports and components

(Figure A)

Technical line drawing of a mechanical device with internal components and alignment lines (no text or symbols)

(Figure B)

AXXESS INTERFACE INSTALLATION

INTERFACE FEATURES

• Provides accessory power (12-volt 10-amp)
  • Retains R.A.P. (retained accessory power)
• Touchscreen for retention of climate control functions
• Micro "B" USB updatable

TABLE OF CONTENTS

Connections......6-8
Installation 9
Programming....9
Touchscreen display operation 10-11

INTERFACE COMPONENTS

• Axxess interface (built into the touchscreen display)
• Bean Bus interface
  • 8164 harness
  • 8164 NAV harness
  • 4-pin harness with yellow RCA jacks
• Factory amplifier not retained with this product – an amplifier bypass harness included

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder, and heat shrink • Tape
• Wire cutter • Zip ties

CONNECTIONS

From the LD-8164 harness to the aftermarket radio:

• Connect the Black wire to the ground wire.
• Connect the Yellow wire to the battery wire.
• Connect Red wire to the accessory wire.

- Tape off and disregard the following (4) wires, they will not be used in this application: Gray, Gray/Black, White, White/Black

*For speaker wire connections, refer to the AX-AB-LX4 amplifier bypass harness Instructions

• Locate the 7-pin connector.
• Connect the radio's power antenna to the highlighted Black wire. (Pin 5)

Close-up of a connector with wires and a red circle highlighting a component (no visible text or symbols)

The Yellow/Black 'Bean BUS' wire must be connected properly for this interface to function: Locate the 13 pin connector in the vehicle.

The following connections will have to be made.

• 'Bean BUS (Yellow/Black)' – to the factory Yellow/Black wire.
- Radio's Illumination wire – to the factory Green wire (if desired)

Front of 13 pin connector

Illumination (+) Green wire on factory side Bean BUS (+) Yellow/Black wire on factory side

Wire side of 13 pin connector

Illumination (+) Bean BUS

CONNECTIONS (CONT.)

Use the LD-8164-NAV harness for vehicles with Factory Navigation

From the LD-8164-NAV harness to the aftermarket radio:

• Connect Black to the ground wire
• Connect Yellow to the battery/ memory wire.
• Connect Red to the accessory wire.
• Connect Orange to the Illumination wire.
• Connect Blue to the radio's Antenna/Remote wire.
• Tape off and disregard the following wires: White, White/Black, Gray, and Gray/Black.*

*For speaker wire connections, refer to the AX-AB-LX4 amplifier bypass harness Instructions.

The Yellow/Black 'Bean BUS' wire must be connected properly for this interface to function: Locate the gray 14 pin connector in the vehicle.

The following connections will have to be made.

- Connect the Yellow/Black wire labelled 'Bean BUS' to the Yellow/Black wire on the factory connector.

A military/lineman splice is recommended to ensure a good connection.*

*Always insulate all connections.

Gray (Control Panel)

Yellow/Black – 'Bean BUS' wire

- Connect to labeled wire on LD-8164

The following connections are only necessary if installing a Multimedia / Navigation radio & desire the additional outputs:

• Connect the radios Vehicle Speed Sense wire to the factory Violet/White wire.
• Connect the radios Park wire to the factory Red/White wire.

White (Multi Display)

Violet/White – Vehicle Speed Sense

Red/White – Parking Brake

CONNECTIONS (CONT.)

4-pin harness with yellow RCA jacks:

• Backup camera harness (4-pin harness with yellow RCA jacks):
• There are two different methods for connecting an aftermarket camera. To the touchscreen or to the aftermarket radio (see radio manual)
• If connecting a backup camera to the touchscreen display is desired, connect the Yellow RCA jack labeled "Rearview camera", to the aftermarket camera.
• IF this method is chosen, see camera options in the Configuration Settings section.
• Disregard the Yellow RCA jack labeled "AUX video", it will not be used in this application.

Amplifier bypass:

Use the included amplifier bypass to connect to the speakers. Take note that there are multiple speakers with varying impedance. An external amplifier and crossovers are recommended.

AX-AB-LX4:

From the 10p Connector:

Green Rear Left Door Speaker (+) Green/Black Rear Left Door Speaker (-) Gray Front Right Speaker / Tweeter (+) Gray/Black Front Right Speaker / Tweeter (-) White Front Left Speaker / Tweeter (+) White/Black Front Left Speaker / Tweeter (-)

From the 6p Connector:

Green/White Subwoofer 1 (+) (If applicable)

White/Red Subwoofer 1 (-) (If applicable)

Purple Rear Right Door Speaker (+)

Purple/Black Rear Right Door Speaker (-)

Brown/Yellow Subwoofer (+)

Brown/Blue Subwoofer (-)

INSTALLING THE INTERFACE

It is highly advisable to read the following steps beforehand, to ensure a clear understanding of what is to be expected. The following steps must be done in the order that they are numbered.

With the vehicle completely off:

Touchscreen display

1. Connect the 8164 harness to the wiring harnesses in the vehicle. Then insert the 8164 harness into port "A" in the touchscreen display.
2. If adding an aftermarket back-up camera to the touchscreen. Connect the 4-pin harness with yellow RCA jacks into port "C" in the touchscreen display.
3. Disregard port "E" and "B" and "D", it will not be used in this application.
4. Port "F" is an update port for future firmware upgrades.

A F D C B E

1. Locate the factory antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra.

PROGRAMMING

• Open the drivers door and keep open during the process.
• Cycle the ignition to on.
• Connect the harnessing to the vehicle.
• Wait until the radio powers on and the touchscreen displays "SWC configured".
  • Cycle the ignition off and back on.
• Test all functions.

FINAL ASSEMBLY

1. Secure the completed assembly into the dash using the factory hardware and reassemble the dash in reverse order of disassembly.

HVAC control screen Configuration Settings screen

5 A/C MAX RECIRC FRONT REAR

• This is the HVAC control screen which will be displayed on the touchscreen display. This is considered the main screen.
• The upper right tab with the gear icon will take you to the Configuration Settings screen.
  • The climate controls will function in the same manner that they did with the factory climate controls.

Configuration Settings Backlight Backup Camera System Config

Backlight

- For controlling the color of the buttons and back-light intensity.

Backup Camera

- Enable/disable the backup camera image to the touchscreen display. Disabled by default.

System Configuration

• About - Information regarding the software in the kit.
• Vehicle Config – Factory features.
• Reset Vehicle Type - To reset the kit to default settings.

Touchscreen calibration:

• Press and hold the upper two soft buttons on either side of the touchscreen for 10 seconds.
• A screen will pop up asking for you to press the target in the screen.
• After pressing the target with your finger, the calibration process will be complete, and the screen will disappear.

Having difficulties? We're here to help.

our Tech Support line at:

386-257-1187

mail at:

[e-mail]

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM

Saturday: 10:00 AM - 5:00 PM

Sunday: 10:00 AM - 4:00 PM

Metra recommends MECP certified technicians