99-3309B-LC - Unspecified AXESS - Free user manual and instructions

USER MANUAL 99-3309B-LC AXESS

Installation instructions for part 99-3309B-LC

Chevrolet Spark 2013-2015 99-3309B-LC

KIT FEATURES

• ISO DIN radio provision with pocket
• ISO DDIN radio provision
- Painted matte black to match the factory dash

Interior view of a car dashboard with air vent and control panel (no visible text or symbols)

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8" Phillips screws
• E) (10) White plastic panel clips • F) Axxess Interface included (not shown)

A

BCDE

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • Axxess Interface included

Antenna Adapter: • 40-EU55

Table of Contents

Dash Disassembly 2

Kit Preparation....2

Kit Assembly

• ISO DIN radio provision with pocket....3
• ISO DDIN radio provision .... 3

Axxess Interface Installation 4

• Connections to be made....4
• Installing the Axxess interface 5
• Initializing the Axxess interface 5
• Vehicle customization with the optional AX-LCD ... 5

TOOLS REQUIRED

- Panel removal tool - Phillips screwdriver

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

99-3309B-LC

Dash Disassembly

1. Unclip and remove the radio trim panel. (Figure A)
2. Remove (4) Phillips screws securing the factory radio and then remove. (Figure B)

Continue to Kit Preparation

Interior view of a car dashboard with air vent and control panel (no text or symbols visible)

(Figure A)

Line drawing of a car dashboard with control panel and buttons (no text or symbols)

(Figure B)

Kit Preparation

From the factory radio trim panel (Figure A):

1. Unclip and remove the A/C vents.
2. Unclip and remove the hazard button.
3. Remove (5) Phillips screws securing the upper display shroud.

From the 99-3309B-LC radio trim panel (Figure B):

1. Snap in the factory A/C vents.

2. Attach the (10) panel clips supplied.

Continue to Kit Assembly

Step 3 Step 1 Step 2 Step 3

(Figure A)

Diagram of a car air intake structure with no visible text or symbols

(Figure B)

99-3309B-LC

Kit Assembly

ISO DIN radio provision with pocket

1. Secure the pocket to the radio brackets with the (4) #8 x 3/8" Phillips screws supplied. (Figure A)
2. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
3. Slide the radio between the radio brackets and secure with screws supplied with the radio. (Figure A)
4. Continue to Axxess Interface Installation, and once completed, reassemble the dash in reverse order of disassembly using the 99-3309B-LC radio trim panel instead of the factory panel.

Technical diagram of a device with labeled components and directional arrows indicating assembly or movement

(Figure A)

ISO DDIN radio provision

1. Slide the radio between the radio brackets and secure with the screws supplied with the radio. (Figure A)
2. Continue to Axxess Interface Installation, and once completed, reassemble the dash in reverse order of disassembly using the 99-3309B-LC radio trim panel instead of the factory panel.

Technical diagram of an electronic device with labeled ports and internal components

(Figure A)

99-3309B-LC

Axxess interface Installation

FEATURES

• Provides accessory power (12-volt 10-amp)
  • Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and speed sense)
  • Used in non-amplified models
  • Used in models without OnStar
• Retains all warning chimes
  • High level speaker input
• Retains balance and fade
• Micro "B" USB updatable

INTERFACE COMPONENTS

• 3309B-LC interface • 3309B-LC harness

TOOLS REQUIRED

- Wire cutter • Crimping tool • Tape • Solder gun

- Connectors (butt-connectors, bell caps, etc.)

Connections to be made

From the 3309B-LC harness to the aftermarket radio:

• Connect the Black wire to the ground wire.
• Connect the Yellow wire to the battery wire.
• Connect the Red wire to the accessory wire.
• Tape off and disregard the Pink wire, it will not be used in this application.
• Connect the Blue/White wire to the power antenna wire.
• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
• Connect the White wire to the left front positive speaker output.
• Connect the White/Black wire to the left front negative speaker output.
• Connect the Gray wire to the right front positive speaker output.
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the Green wire to the left rear positive speaker output.
• Connect the Green/Black wire to the left rear negative speaker output.
• Connect the Purple wire to the right rear positive speaker output.
• Connect the Purple/Black wire to the right rear negative speaker output.
  The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the Blue/Pink wire to the VSS/speed sense wire.
• Connect the Green/Purple wire to the reverse wire.
• Connect the Light Green wire to the parking brake wire.

99-3309B-LC

Installing the Axxess interface

With the key in the off position:

- Connect the 3309B-LC harness into the interface, and then to the wiring harness in the vehicle.

Initializing the Axxess interface

Attention: If the Axxess interface loses power for any reason, the following steps will need to be performed again.

- Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on.

Note: If the radio does not come on within 60 seconds, turn the key to the off position, disconnect the interface, check all connections, reconnect the interface, and then try again.

- Turn the key to the off position, and then to the accessory position.

- Test all functions of the installation for proper operation, before reassembling the dash.

Vehicle customization with the optional AX-LCD (sold separately)

The AX-LCD allows the retention of the vehicles personalization menu that is lost after removing the OE radio.

From the DIN harness with leads on the AX-LCD harness:

• Connect the Black wire to ground.
• Connect the Red wire to accessory power.
• Connect the Pink wire to the Pink wire of the 3309B-LC harness. Note: This wire will have to be soldered onto the 3309B-LC.
• Tape off and disregard the Blue/Pink wire, it will not be used in this application.
• Press and hold the "Return/ESC" button on the LCD screen for 5 seconds until "Select Interface" comes up.
• Select "Connection Type", and then press "Enter"
• Scroll up or down to "Gateway", and then press "Enter"
• Once done, press the "Return/ESC" button two times to get back to the main menu.

99-3309B-LC

Notes

99-3309B-LC

Notes

Installation instructions for part 99-3309B-LC

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by parrolling in the most recognized and suggested

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

606-334-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP

certified technicians

Metra

Interior view of a car dashboard with air vent and control panel (no visible text or symbols)

COMPONENTES DEL KIT

Line drawing of a car dashboard with control panel and rear seats (no text or symbols)

(Figura A)

Line drawing of a car dashboard with arrows pointing to the screen (no text or symbols)

(Figura B)

Preparación del kit

Line drawing of a car air intake manifold with no text or symbols

(Figura B)

99-3309B-LC

Ensamble del kit

Technical line drawing of a mechanical device with labeled components (no text or symbols present)

(Figura A)

Technical diagram of an electronic device with labeled ports and internal components

(Figura A)

99-3309B-LC

Móvil (Mobile Electronics

(Certification Program, MECP).