99-3010S-LC - Car stereo AXESS - Free user manual and instructions

USER MANUAL 99-3010S-LC AXESS

Installation instructions for 99-30105-LC

U.S. PATENT # D639,794

Chevrolet Camaro 2010-2015 99-3010S-LC

KIT FEATURES

• DIN radio provision with pocket
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
- Painted silver to match factory finish

12 Battery A1 Altitude: 0.8 Pin Speed: 500 Rig/Line: 0 TOM: 36 LHNOPCASTLWXT

KIT COMPONENTS

• A) Radio trim panel • B) Radio housing • C) ISO brackets • D) ISO trim plate • E) ISO DDIN brackets
• F) ISO DDIN trim plate • G) Pocket • H) Axxess interface and harness (not shown)

ABCDE

F

G

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness:

- Axxess interface included

Antenna Adapter:

• 40-EU55

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver
• 7mm socket wrench • T-20 Torx Wrench • Cutting tool

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

99-30105-LC

Table of Contents

Dash Disassembly 2-3

Kit Preparation....3

Kit Assembly

• DIN radio provision with pocket ....4
• ISO DIN radio provision with pocket ....4
• ISO DDIN radio provision....5

Axxess Interface Installation

• Connection to be made....6
• Installing the Axxess interface......6
• Initializing the Axxess interface ....6
• Vehicle customization with optional AX-LCD......7
• Changing display backlight color....7

Dash Disassembly

For vehicles without UMQ gauge panel, unsnap and remove shifter trim panel and skip to step 8.

1. Unclip and remove the (2) side trim panels running the length of the center console. (Figure A)
2. Remove (1) Phillips screw from each side of the front of the center console. (Figure B)
3. Remove (2) Phillips screws per side from the cover on the back of the center console then unclip and remove the cover. (Figure C)
4. Remove (2) Phillips screws exposed under the cover on the back of console. (Figure D)
5. Remove gauge cluster/trim panel around shifter. (Figure E)

Continue onto next page

Technical line drawing of a car dashboard and steering wheel assembly (no text or symbols)

(Figure A)

Diagram of a car interior showing dashboard, steering wheel, and directional arrows (no text or labels)

(Figure B)

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figure C)

Diagram of a car interior showing dashboard and steering wheel (no text or symbols)

(Figure D)

99-30105-LC

Dash Disassembly

1. For automatic models, remove one T-20 Torx screw from the front of the shifter, and then remove the knob and shifter surround panel. (Figure F)
2. Remove (4) Phillips screws now exposed, and then lift up on the rear of the center console. Slide toward the back of the vehicle then unclip and remove the entire center console. (Figure G)
3. Remove (2) 7mm screws securing the climate control/radio trim panel and remove. (Figure H)
4. Remove (4) 7mm screws securing the radio chassis, and then remove. (Figure I)

Continue to kit preparation

Interior view of a car gear shift lever mechanism (no text or symbols visible)

(Figure E)

Mechanical assembly diagram showing a lever mechanism interacting with a car (no text or symbols visible)

(Figure F)

Diagram of a car interior showing dashboard, steering wheel, and seat area with directional arrows (no text or labels)

(Figure G)

Diagram of a robotic arm operating on a vehicle surface with no visible text or symbols

(Figure H)

Kit Preparation

1. Cut and remove the sub dash radio support to make room for the interface and harnesses. (Figure A)
2. Remove panel clips from factory radio and attach to the top of the kit housing. (Figure B)

Note: Panel clips have been provided in case the factory clips have been damaged or missing.

Continue to kit assembly

Interior view of a car dashboard with directional arrows indicating traffic or movement (no text or symbols visible)

(Figure I)

Top-down schematic of a vehicle dashboard with no text or symbols

(Figure A)

Diagram of a car dashboard with sensors and control buttons (no text or labels)

(Figure B)

99-30105-LC

Kit Assembly

DIN radio provision with pocket

1. Remove the metal DIN sleeve from the aftermarket radio.
2. Slide the sleeve into the radio housing and secure by bending the metal locking tabs down. (Figure A)
3. Snap the pocket into the bottom opening of the radio housing. (Figure B)
4. Slide the radio back into the sleeve until it clicks in. (Figure B)
5. Continue to Axxess Interface Installation, and once completed, reassemble the dash in reverse order of disassembly using the 99-3010S-LC radio trim panel instead of the factory panel.

Illustration of a hand using a tool to adjust or install a component, with no visible text or symbols.

(Figure A)

Technical line drawing of a mechanical device with directional arrows indicating motion or flow (no text or symbols)

(Figure B)

ISO DIN radio provision with pocket

1. Remove the metal DIN sleeve and trim ring from the aftermarket radio.
2. Mount the ISO brackets to the radio with the screws supplied with the radio. (Figure A)
3. Snap the pocket into the bottom opening of the radio housing. (Figure B)
4. Slide the radio into the radio opening until the side clips engage. (Figure B)
5. Snap the ISO trim plate into the radio housing. (Figure C)
6. Continue to Axxess Interface Installation, and once completed, reassemble the dash in reverse order of disassembly using the 99-3010S-LC radio trim panel instead of the factory panel.

Technical line drawing of a mechanical device with mounting flanges and central housing (no text or symbols)

(Figure A)

Technical line drawing of a mechanical device with internal components and directional arrows (no text or symbols)

(Figure B)

Technical line drawing of a device with mounting brackets and a central panel (no text or symbols)

(Figure C)

Kit Assembly

ISO DDIN radio provision

1. Cut and remove the center support. (Figure A)
2. Snap the ISO DDIN brackets to the inside edge of the radio housing. (Figure B)
3. Slide the radio into the bracket/radio housing assembly and secure it using the screws supplied with the radio. (Figure C)
4. Snap the ISO DDIN trim plate into the radio housing. (Figure C)
5. Continue to Axxess Interface Installation, and once completed, reassemble the dash in reverse order of disassembly using the 99-3010S-LC radio trim panel instead of the factory panel.

Line drawing of a hand using a tool to adjust or install a metal bracket (no text or symbols)

(Figure A)

Technical line drawing of a rectangular mechanical housing with directional arrows indicating movement (no text or symbols)

(Figure B)

Isometric line drawing of a device chassis with arrows indicating movement or force (no text or symbols)

(Figure C)

Axxess interface Installation

FEATURES

• Provides accessory power (12-volt 10-amp)
  • Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, and speed sense)
  • Used in non-amplified models
  • Used in models without OnStar
• Retains all warning chimes
  • High level speaker input
• Retains balance and fade
• Micro "B" USB updatable

INTERFACE COMPONENTS

• 3010S-LC interface • 3010S-LC harness

TOOLS REQUIRED

• Wire cutter • Crimping tool • Tape • Solder gun
• Connectors (butt-connectors, bell caps, etc.)

Metra

Axxess interface installation 99-30105-LC

Connections to be made

From the 3010S-LC harness to the aftermarket radio:

• Connect the Black wire to the ground wire.
• Connect the Yellow wire to the battery wire.
• Connect the Red wire to the accessory wire.
• Connect the Pink wire to the Pink wire located in the HVAC harness (ignore the writing on this wire, this is NOT a "mute" wire).
• Connect the Blue/White wire to the power antenna wire.
• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
• Connect the White wire to the left front positive speaker output.
• Connect the White/Black wire to the left front negative speaker output.
• Connect the Gray wire to the right front positive speaker output.
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the Green wire to the left rear positive speaker output.
• Connect the Green/Black wire to the left rear negative speaker output.
• Connect the Purple wire to the right rear positive speaker output.
• Connect the Purple/Black wire to the right rear negative speaker output.
  The following (3) wires are only for multimedia/navigation radios that require these wires.
• Connect the Blue/Pink wire to the VSS/speed sense wire.
• Connect the Green/Purple wire to the reverse wire.
• Connect the Light Green wire to the parking brake wire.

Installing the Axxess interface

With the key in the off position:

- Connect the 3010S-LC harness into the interface, and then to the wiring harness in the vehicle.

Initializing the Axxess interface

Attention: If the Axxess interface loses power for any reason, the following steps will need to be performed again.

• Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on.
  Note: If the radio does not come on within 60 seconds, turn the key to the off position, disconnect the interface, check all connections, reconnect the interface, and then try again.
• Turn the key to the off position, and then start the vehicle.
• Cycle the A/C fan speed all the way to high, and then back to low.
• Test all functions of the installation for proper operation, before reassembling the dash.

Metra

Axxess interface installation 99-30105-LC

Vehicle customization with the optional AX-LCD (sold separately)

The AX-LCD allows the retention of the vehicles personalization menu that is lost after removing the OE radio.

From the DIN harness with leads on the AX-LCD harness:

• Connect the Black wire to ground.
• Connect the Red wire to accessory power.
• Connect the Pink wire to the Pink wire of the 3010S-LC harness. Note: This wire will have to be soldered onto the 3010S-LC.
• Tape off and disregard the Blue/Pink wire, it will not be used in this application.
• Press and hold the "Return/ESC" button on the LCD screen for 5 seconds until "Select Interface" comes up.
• Select "Connection Type", and then press "Enter"
• Scroll up or down to "Gateway", and then press "Enter"

• Once done, press the "Return/ESC" button two times to get back to the main menu.

• Press the front defrost button for 5 seconds, this will engage the "Configure Backlight Color" mode. (Figure A) Note: Backlight will blink while in this mode.

• Create your backlight color (Figure A):

• Press and hold the "Face" button to increase Red.

• Press the "Foot" button to decrease Red.
• Press and hold the "Face/Foot" button to increase Green.

Changing display

• Press and hold the "Def/Foot" button to decrease Green.
• Press and hold the "Fan Up" button to increase Blue.

• Press and hold the "Fan Down" button to decrease Blue.

• After you have your desired color stop pressing the button(s) and the blinking will stop leaving your desired color. (Figure A)

Red Green Blue Color level up Color level down Temp↑ TEMP↓ Press and hold to enter "Configure backlight color" mode (Figure A)

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by parrolling in the most recognized and suggested

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

606-334-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP

certified technicians

U.S. PATENT # D639,794

Chevrolet Camaro 2010-2015 99-3010S-LC

CARACTERÍSTICAS DEL KIT

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figura A)

Diagram of a car interior showing dashboard, steering wheel, and directional arrows indicating movement (no text or symbols)

(Figura B)

Technical line drawing of a mechanical assembly with no visible text or symbols

(Figura C)

Diagram of a car interior showing dashboard and steering wheel (no text or symbols)

(Figura D)

99-30105-LC

Interior view of a car gear shift lever mechanism (no text or symbols visible)

(Figura E)

Mechanical assembly diagram showing a lever mechanism with no visible text or symbols

(Figura F)

Diagram of a car interior showing dashboard, steering wheel, and seat area with directional arrows (no text or labels)

(Figura G)

Diagram of a robotic arm operating on a vehicle surface with no visible text or symbols

(Figura H)

Preparación del kit

Interior view of a car dashboard and infotainment system (no visible text or symbols)

(Figura I)

Top-down schematic of a vehicle dashboard with no text or symbols

(Figura A)

Diagram of a car dashboard with sensors and control buttons (no text or labels)

(Figura B)

99-30105-LC

Ensamble del kit

Illustration of a hand using a tool to adjust or install a component, with no visible text or symbols.

(Figura A)

Technical line drawing of a mechanical device with directional arrows indicating motion or flow (no text or symbols)

(Figura B)

Technical line drawing of a mechanical device with mounting flanges and a central housing (no text or symbols)

(Figura A)

Technical line drawing of a mechanical device with internal components and directional arrows (no text or symbols)

(Figura B)

Technical line drawing of a device with mounting brackets and control panel (no text or symbols)

(Figura C)

Ensamble del kit

Line drawing of a hand using a tool to adjust or install a metal bracket (no text or symbols)

(Figura A)

Technical line drawing of a mechanical housing component with directional arrows indicating movement (no text or symbols)

(Figure B)

Technical line drawing of a device with internal components and directional arrows (no text or symbols)

(Figura C)