MI-709 - Wall mount Mount-It! - Free user manual and instructions

USER MANUAL MI-709 Mount-It!

Installation Instruction

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

UNPACKING INSTRUCTIONS

• Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
• Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts.
• Carefully read all instructions before attempting installation.

IMPORTANT SAFETY INFORMATION

• Install and operate this device with care. Please read this instruction before installation, and carefully follow all instructions contained herein. Use proper safety equipment during installation.
• Please call a qualified installation contractor for help if you don't understand these directions or have any doubts about the safety of the installation.

Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaims any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Supplied Parts List
(1)Pole-a	(1)"C" Clamp-b	(1)"C" Clamp Brace-c	(1)Monitor Arm-d
	(1)Support Plate-f(1)M10 Bolt-e (1)M10 Washer-g (1)Spring Washer-h
(1)Grommet Base Plate-i	(3)M5x14 Bolt-j	(2)M8x12 Bolt-k (1)VESA Plate-l
	(2)Adapter-n1(1)Wire Clip-m (2)Adapter-n2 (8)M4x10 Bolt-o
(12)M4 Washer-p	(8)M4 Nut-q	(1)M4X6 Bolt-r	(4)M4X12 Thumb Bolt-s
	(4)M6x20 Bolt-u (4)M8x20 Bolt-v		(4)M4 Spacer-w(4)M4
(4)M6/M8 Spacer-x	(1)Allen Key-y (1)Wrench-z
2

Option A: Desk Clamp Install

1. Install the "C" -Clamp Brace (c) to the Pole (a) using 3pcs M5x14 Bolts (j), and tighten using the Allen Key (y), see Figure 1.
2. Install the "C" -Clamp (b) to the pole assembly according to the thickness of the desktop. The thickness can be changed to three positions. Connect it using 2pcs M8x12 Bolts (k), and tighten using the Allen Key (y). Tighten the "C" -Clamp to the desktop using the plastic knob, see Figure 2.

a j c

en Key (y), see Figure 1. ll the "C" -Clamp (b) to the pole assembly ing to the thickness of the desktop. The ess can be changed to three positions. ct it using 2pcs M8x12 Bolts (k), and n using the Allen Key (y). Tighten the amp to the desktop using the plastic ee Figure 2. Figure 2 k b Plastic Knob v j C Figure 1

Option B: Grommet Base Install

Existing Grommet Hole Installation

If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount.

1. Install the Grommet Base Plate (i) to the Pole (a) using 3pcs M5x14 Bolts (j), and tighten using the Allen Key (y), see Figure 3.
2. Position the Pole (a) on the mounting surface and secure using the Support Plate (f), M10 Washer (g), Spring Washer (h) and M10 Bolt (e). Fasten the M10 Bolt using provided Wrench (z), see Figure 4.

a i j

Figure 3

f g h e Fi

Figure 4

Option B: Grommet Base Install

Self Drilled Grommet Hole Installation

1. Position the Pole (a) on the mounting surface and mark the center hole. Drill a 3/8" (10mm) diameter hole at the marked position through the mounting surface.
2. Install the Grommet Base Plate (i) to the Pole (a) using 3pcs M5x14 Bolts (j), and tighten using the Allen Key (y), see Figure 5.
3. Position the Pole (a) on the mounting surface and secure using the Support Plate (f), M10 Washer (g), Spring Washer (h) and M10 Bolt (e). Fasten the M10 Bolt using provided Wrench (z), see Figure 6.

a i j

Figure 5

Fi h g f e

Figure 6

Step 2

Install Arm to the Pole

Install Monitor Arm (d) to the Pole (a). Fasten the bolt with supplied Allen Key (y). Attach the Wire Clip(m) to the Pole (a) and Monitor Arm (d).

d y

m

Step 3A

Attach VESA Plate to the Mounting Hole of TV For VESA 75x75mm and 100x100mm Mounting Holes

For Monitor with Flat Back

W t For Monitor with Curved or Recessed Back

Step 3B

Attach VESA Plate to the Mounting Hole of TV For VESA 200x100mm Mounting Holes

250mm 200mm 100mm

Technical diagram of mechanical components with labeled parts including q, p, and O

s to v p

For Monitor with Flat Back

s to v p

For Monitor with Curved or Recessed Back

200mm 170mm 200mm 170mm

Technical diagram of mechanical components with labeled parts including O, p, q, and others

s to v p

s to v p W,X

For Monitor with Flat Back For Monitor with Curved or Recessed Back

Step 4

Slide the Monitor onto the Head of Monitor Arm

Technical line drawing of a mechanical assembly with rotating components and directional arrows (no text or symbols)

Slide the monitor onto the head of Monitor Arm (d) as shown in the above diagram.

Technical line drawing of a mechanical assembly with no visible text or symbols

Install the M4x6 Bolt (r). Make sure the bolt is installed before you rotate the monitor.

Adjust the Tilt Angle and Manage the Wires

grub screw

Fasten the grub screw in Monitor Arm to fix the tilting angle by provided Allen Key (y).

Technical line drawing of a mechanical assembly with coiled wires and a vertical rod (no text or symbols)

Manage the wires as the above diagram.