95-7877S - Kit voiture Metra - Free user manual and instructions

USER MANUAL 95-7877S Metra

Installation instructions for part 95-7877

Honda Fit 2009-2013 95-7877

KIT FEATURES

• ISO DDIN radio provision
- Painted to match factory dash

95-7877S - Silver

95-7877B - Matte Black

Interior view of a car dashboard with a digital display showing a vehicle (no visible text or symbols)

KIT COMPONENTS

• A) Radio housing • B) ISO DDIN brackets • C) ISO DDIN trim plate

A

B

C

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-1729

Antenna Adapter: • 40-HD10 • 40-HD11 (with NAV)

TOOLS REQUIRED

- Panel removal tool - Phillips screwdriver - 8mm Socket wrench

Table of Contents

Dash Disassembly 2

Kit Preparation....3

Kit Assembly

- ISO DDIN radio provision .... 3

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

95-7877

Dash Disassembly

1. Unclip and remove the lower center panel below radio. (Figure A)
2. Remove (1) 8mm bolt facing up behind center panel.

Note: Slide the recirculation control lever to FRESH for better access to bolt. (Figure A)

1. Open the upper glove box then use a pry tool to unclip and remove the radio/climate control assembly. (Figure B & C)
2. Remove (2) Phillips screws securing the hazard switch to the back of the factory radio panel. (Figure D)

Line drawing of a car interior showing dashboard, air intake, and control panel (no text or symbols)

(Figure A)

Line drawing of a car dashboard with a hand adjusting the steering wheel (no text or symbols)

(Figure B)

Line drawing of a car dashboard and air intake system (no text or symbols)

(Figure C)

1. Remove (2) Phillips screws securing the air bag light to the back of the factory radio panel. (Figure E)
2. Remove (5) Phillips screws securing the A/C vents to the radio panel.
3. Remove (7) retaining clips from radio housing to be used later in kit preparation.

Continue to kit preparation

REAR FACTORY RADIO PANEL

(Figure D)

REAR FACTORY RADIO PANEL

(Figure E)

95-7877

Kit Preparation Kit Assembly

1. Secure the hazard switch into the radio housing panel using the factory hardware. (Figure A)
2. Secure the air bag light into the radio housing panel using the factory hardware. (Figure A)
3. Secure the A/C vents to the radio housing using the factory hardware. (Figure B)
4. Attach the (7) retaining clips to the radio housing panel in the same location as removed from the factory radio panel.

Continue to kit assembly

Technical line drawing of a car front panel with directional arrows indicating movement (no text or symbols)

(Figure A) (Figure A)

Line drawing of a car air vent system (no text or symbols)

(Figure B) (Figure B)

ISO DDIN radio provision

1. Snap the ISO DDIN brackets into the inside edge of the radio housing. (Figure A)
2. Slide the radio into the bracket/radio housing assembly and secure the radio into the assembly using the screws supplied with the radio. (Figure B)
3. Snap the ISO DDIN trim plate onto the front of the radio/housing assembly. (Figure B)
4. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Test the radio for proper operation.
5. Reassemble the dash in reverse order of disassembly.

Technical line drawing of a car air intake manifold (no text or symbols)

Technical line drawing of a car air conditioner unit with internal components and mounting bracket (no text or labels)

Installation instructions for part 95-7877

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Metra

Interior view of a car dashboard with a digital display showing a vehicle (no visible text or symbols)

COMPONENTES DEL KIT

Line drawing of a car interior showing dashboard, air intake, and control panel (no text or symbols)

(Figura A)

Line drawing of a car dashboard with a hand adjusting the steering wheel (no text or symbols)

(Figura B)

Line drawing of a car dashboard and air intake system (no text or symbols)

(Figura C)

Line drawing of a car front panel with directional arrows indicating movement (no text or symbols)

(Figura A) (Figura A)

Line drawing of a car air vent system with airflow direction arrows (no text or symbols)

(Figura B) (Figura B)

Technical line drawing of a car air intake manifold (no text or symbols)

Technical line drawing of a car air conditioner unit with internal components and mounting bracket (no text or labels)