E20V - Elevator Eoslift - Free user manual and instructions

USER MANUAL E20V Eoslift

Line drawing of a manual pallet jack with wheels and handle (no text or symbols)

Eoslift

E20V

Operating Instructions

Scale

Pallet

Truck

Eoslift

Eoslift Automation Technology Corp.

No. 95 Yorja Road, Yountong Town, Hilyan, Zhitleng Pashare, Chiu 374311

[Unreadable]

F50:3007861222901

17.5.09-27

Holding: 400-626-9090

E20V Series Scale Pallet Trucks

Esteemed users:

For proper and safe operation of the products, before using the products, be sure to read the operating instructions carefully and retain them properly for future reference.

The operator needs to have proficient operation skills. The operator has responsibility to carefully understand the performance and safety rules of the pallet truck. If you have any doubts during the application, please don't hesitate to contact Eoslift.

Eoslift

E20V Series Scale Pallet Trucks

Table of contents

I. Technical parameters	01
II. Safety rules	02
III. Installation of handles	03
IV. Adjusting the finger grip handle	04
V. Operating instruction	05
VI. Appendix	13
VII. Troubleshooting	14
VIII. Transport, loading, test run and storage	16
IX. Parts list	17

Technical parameters

Model		E20V
Rated capacity	kg	2000
Load center	mm	600
Dead-weight	kg	130
Wheel material		PU/NYLON
Maximum error	%	0.05
Maximum fork height [H]	mm	190/200
Minimum fork height [H]	mm	75/85
Steering wheel	mm	180 × 50
Load-bearing wheel	mm	80 × 70
Overall fork width [B]	mm	560/685
Fork length [L]	mm	1150/1220
Length of the truck [L1]	mm	1580/1650
Minimum turning radius [R]	mm	1325/1395
Type of battery		Button cells
Battery capacity	mAh	2x900

Technical line drawing of a mechanical device with wheels and a handle (no text or symbols)

Technical line drawing of a mechanical component with no visible text or symbols

Safety rules

E20V Series Scale Pallet Trucks

Eoslift

The pallet truck is only applicable to indoor use and the application environment must meet the following conditions:
Free from rainwater or corrosion of harmful gases;
Room temperature of -20°C-+40°C;
Relative ambient humidity <90%;
and Requirements for ground: hard, anti-skid and level without barriers.
Before using the pallet truck, the operator must read the operating instructions and the warning labels on the truck body carefully.
- Do not use this truck on the muddy ground
- Do not operate the pallet truck unless you are fully familiar with it and have been authorized to do so.
- Do not operate the pallet truck unless you have carefully checked its condition. Pay special attention to the wheels, the handle assemblies, the truck frame, the unloading plate, etc. To pull the truck, always move the finger grip control handle into the middle position. This makes the handle easier to move and reduces the rebounce of the handle by the small piston. This also preserves the hydraulic seals and the piston components. A long service life can be expected.
- Do not carry or lift passengers.
The operator shall wear safety shoes and gloves for protection.
▶ While the goods are being transported, all people should stay 600mm away from the truck frame.
▶ Overload is prohibited.
- Do not use the truck in a potentially flammable and explosive atmosphere.
▶ Do not use the truck as a vehicle jack.
- Do not use the truck during strong wind forces.
- Do not use the truck on places insufficiently illuminated.
▶ Under special conditions or in special locations, the operator should be careful while operating the pallet truck.

Diagram showing a mechanical component with labeled parts and an inset view of a multi-view diagram with symbols like 'Φ' and 'φ'.

Installation of handles

Simple line drawing of a tool or instrument with an angle labeled 0°, no text or symbols present.

1. Make sure the chain on the handle is in this position shown in the picture

Technical line drawing of a mechanical assembly with no visible text or symbols

1. Push the handle shaft through the holes Fix it with the spring pin.

Technical line drawing of a mechanical assembly (no text or symbols)

1. Put the chain through the hole on the shaft.

Technical line drawing of a mechanical assembly with gears and shafts (no text or symbols)

Technical line drawing of a mechanical assembly with no visible text or symbols

1. Fix the chain in the slot of the unloading plate.

Technical line drawing of a mechanical assembly with no visible text or symbols

1. Pull the shaft from the hole. Then the assembly is complete.

Adjusting the finger grip handle

E20V Series Scale Pallet Trucks

Eoslift

On the handle of this pallet truck, you can find finger grip control handle(1-1) which can be regulated in three positions:

1-1 Upper Middle Lower

Lifting-set the control handle at lower position
② Middle position: set the control handle at middle position
3 Lowering: set the control handle at upper position. The handle moves back to the middle position when released.

However if the truck cannot operate normally under three positions, you can adjust them according to the following steps:

①If the forks elevate while pumping in the Middle position, turn the adjusting nut (2-4) on the adjusting bolt (2-3) or screw (2-6) clockwise until pumping action does not raise the forks and the finger grip control handle works properly Middle position.
2 If the forks descend while pumping in the Middle position, turn the screw(2-6) or nut(2-6) counter clockwise until the forks stop descending.
③ If the forks do not descend when the finger grip control handle (1-1) is in the Lowering position, turn the nut (2-4) or screw (2-6) clockwise until raising the control handle lowers the forks. Then check the Middle position according to items ① and ② to make sure the nut (2-4) and screw(2-6) are in the proper position.
② If the forks do not elevate when the finger grip control handle is in the Lifting position, turn the nut (2-4) or screw (2-6) counterclockwise until the forks elevate. Then check the function of the Lowering position and Middle position according to items ①, ② and ③ is normal.

2-3 2-4 2-6

Operating Instructions

E20V Series Scale Pallet Trucks

Eoslift

1. Using the Scale Pallet Truck

The truck shall be correctly used to ensure accurate weighing. The following conditions are prohibited in the application.

X OK

min -10 °C 15 °F 0 max 40 °C 105 °F 0 -2° × × > max. × IP 53 ×

2.Normal weighing mode

2.1 Operating panel

100 kg (1) (2) (3) B. L/OT O T U (4) (5) (6) (7) (8) (9) (10) (11)

Figure 2-1 Operating panel in Normal Weighing Mode

① Weight display
② Unit of measurement
3 Battery level
4 Zero
5 On/Off back light
6 Unit switching
7 Backlight cursor
8 Dynamic cursor
9 Tare cursor
10 Net weight cursor
11 Zero cursor

Note: Abbreviations for the following keys:

Zero key-0"key

Tare removal key--*T*key

Unit switch key - "U" key

ON/OFF key - "P" key

Operating Instructions

E20V Series Scale Pallet Trucks

Eoslift

2.2 Display

If any cargo is placed on the frame, its weight will be displayed after 1 second; once “dynamic cursor” disappears, value as displayed on the screen will be the weight of the cargo.

2.3 Key function

①Display function

Zero key ("0") --Reset instrument readings within the permissible range.

Tare removal key ('1')—Current weight is taken as the tare weight for tare removal based on the gross weight; whereas the instrument is to be switched over to the net weight for display. Recover the tare weight as deducted at the net weight, and switch the instrument to the gross weight for display.

Unit switch key ("U")—It is for cyclic switching of measurement unit among KG, T, OZ and LB, representing "kilogram", "ton", "ounce" and "pound" respectively.

ON/OFF key ("P")—Once this key is pressed and held for 2 seconds under ON status, *----* is to be displayed on the screen before power-off; press the key for a while to turn on the back light in the back light mode. Press the key for a while for start-u

② Combination key function

"U" key + "0" key - Factory reset

"U" key + "T" key - enter the parameter setting mode

3. Parameter setting mode

3.1 Operating panel

100 kg 100 kΩ IL LIGHT ↑ ↑ GROSS SET >> 0 T U (4) (5) (6) (7)

Figure 3-1 Operating panel in parameter setting mode

1 Input value

2 Calibration unit
3 Input cursor
4 Option selection
5 Option confirmation
6 Location switching
7 Option cancellation

Press *U* key and *T* key simultaneously in normal display mode to enter the parameter setting mode when "SETUP" is displayed on the screen. The function of the individual key is as follows:

'0' key - option selection

'T' key - option confirmation.

"U" key — option cancellation

*P* key - digit switching in calibration mode.

Press "T" key to confirm entry into parameter setting mode; press "U" key to cancel parameter setting to enter normal display mode.

Operating Instructions

E20V Series Scale Pallet Trucks

Eoslift

3.2 Default unit setting

Default unit of the system is kilogram (KG).

The first option in parameter setting mode is default unit setting; when "UNIT" is displayed on the screen, press "T" key to confirm entry into unit setting mode; press "U" key for cancellation to proceed with next setting.

Once default unit setting is confirmed, press "0" key repeatedly for cyclic switching among the units as displayed on the right side of screen: * KG", "T", "OZ" and * LB", representing "kilogram", "ton", "ounce" and "pound" respectively; press "T" key to confirm the setting, and proceed with next setting.

3.3Back light mode setting

Default back light mode of the system is OFF; shortly press "P" key to turn on the back light when back light cursor is displayed on the screen in back light mode.

Once default unit setup is completed, proceed with setting of back light; when * BLMOD* is displayed on the screen. press * T* key to confirm back light mode setting: press "U" key for cancellation to proceed with next setting.

Once back light mode setting is confirmed, press "0" key for cyclic switching of items displayed on the screen; "BL ON" and "BL OFF" refer to Back Light On and Off respectively; press "T" key to confirm setting, and proceed with next setting.

3.4 Auto Power-off Time Setting

Default auto power-off time of the system is 5 minutes when cargoes remain unchanged.

Proceed with auto power-off time setting once back light mode setting is completed; when "POWTM" is displayed on the screen, press "T" key to confirm entry into auto power-off time setting; press "U" key for cancellation to proceed with next setting.

Once auto power-off time setup is confirmed, press "0" key for cyclic switching among 1-9, representing auto power-off time (in minute); press "T" key to confirm the setup, and proceed with next setup.

4.Calibration

Digital medical device with control panel and display screen showing 'Ω' and 'U' functions

1. Press "U" key and "T" key simultaneously for Setup mode in normal mode.

SETUP O T U

1. Press the 'T' key to enter the setup mode

UNIT UNIT O T U

1. Press the "U" key to skip the "unit settings"

BLMOD O T U

1. Press the "U" key to skip the "back light setting"

POTM PWM O T U

1. Press the 'U' key to skip the 'power-off time setting'

CRL6N O T U

1. Make sure that here is no cargo on the frame, and Press "T" key to confirm calibration.

Operating Instructions

E20V Series Scale Pallet Trucks

Eoslift

80005 O T U 7-1. Press "0"key to input values.

7-2. Press 'P' key to adjust the input digit bit.

800.25V 7-3. Press '0' key to input value of corresponding digit bit.

00025° 25kg 7-4. Example: Calibration with 25KG counterweight.

80025 O T U 8. Complete input, and Press "T" key for confirmation.

CALOK O T U 9. Calibration is deemed to be completed once 'CALOK' is displayed on the screen,

5.Battery replacement

(1) (2)

Diagram for disassembly of battery cover

1 Battery holder
② Battery cover

The instrument uses 2 CR2447 button cells.

As shown in the Figure, slide down instrument battery cover to remove the used battery for replacement; put the new battery into the battery holder, and then close the battery cover.

6. Routine maintenance

Please check the oil level every six months and change the oil every twelve months. 32 # hydraulic oil is recommended, with total volume of about 0.5 liters.
- Replace the battery in time if power monitoring icon as displayed is blank or data displayed is indistinct.
It is better not to put the instrument into prolonged outdoor operation in case of rain and snow; prolonged exposure of instrument to the sunshine is strictly prohibited.
It is applicable to clean the instrument shell with soft and clean cloth in combination with routine washing solvent; never use industrial solvent for cleaning or directly spray it on the instrument surface.
It is recommended that users check the instrument and sensor regularly to ensure its accuracy during use.

Appendix

E20V Series Scale Pallet Trucks

Eoslift

Description of items displayed on the screen

Item	Description
BLMOD	Backlight mode setting
CALBN	Calibration
CALOK	Calibration OK
CANCEL	Cancel parameter settling
FAIL	Plant calibration failed
OUTRG	Out of range
PMODE	Plant calibration mode
POWTIME	Auto power-off time setting
RESET	Factory reset
SS CK	Sensor check
SS OK	Sensor OK
SSERR	Sensor error
SETUP	Parameter setting
TARE	Tare removal
TR ER	Tare removal error
UNTARE	Untare
UNIT	Unit setting
ZERO	Zero
ZR ER	Zero error

Troubleshooting

1. System halt

This product has received strict testing before delivery and no system halt will occur under normal conditions. Please remove the battery, and refit it again to recover its normal operation in case of system halt.

2. Start-up failure

2.1 Turn off the power supply. Disassemble the gauge outfit, and use a voltmeter to measure battery voltage; if the voltage is below 3.5V, it means that battery voltage is extremely low, which may result in start-up failure; replace the old battery with new one in this case.

2.2Disassemble the gauge outfit, and use a voltmeter to measure battery voltage: if the voltage is over 3.5V, just check if the red-black connecting line between battery module and instrument panel is disconnected.

2.3 Other problems. Please contact professionals for testing of panel if power supply is normal.

3.Abnormal display

3.1 If the sensor is proved to be normal through test, just press the unit switching key to see if the data displayed is normal.

3.2 Sensor connection: If display of instrument reading is abnormal, just turn off the instrument and turn on it again to check screen display; if "SSERR" is displayed on the screen following display of "SS CK". It means that connection of sensor is abnormal; in this case, it is necessary to check if connection between the sensor and instrument panel is normal before contacting professionals to check if sensor output is normal.

3.3 Calibration: If abnormal data is still displayed by the instrument following unit switching, just use "unit switching" and "tare removal" in combination to enter the parameter setting mode, and recalibrate at the final setting option (for details, please refer to page 10).

1. Truck failure

No.	Fault	Possible cause	Action
1	The forks cannot be lifted to max. height	The hydraulic oil is insufficient	Add the hydraulic oil
2	The forks cannot be lifted	The hydraulic oil is insufficientThe hydraulic oil has impuritiesAdjusting nut(2-4) or adjusting screw(2-6) in wrong positionsAir enters into the cylinderSeals damaged	Add the hydraulic oilChange hydraulic oilAdjust nut(2-4) or adjusting screw(2-6)Put the finger grip handle in the upper position and press the handle dozens of timesReplace the damaged seals with new seals

Troubleshooting Transport, loading, test run and storage

E20V Series Scale Pallet Trucks

Eoslift

3	The forks cannot be lowered	Piston rod or the frame is deformed resulting from overloading or cargo slanting to one sideThe forks was kept in raised position for extended period of time, then the piston rod is exposed to the air and gets rusted , which blocks the motion of the pistonAdjusting nut(2-4) or adjusting screw(2-6) in wrong positions	Replace the related parts of the cylinder or the frame with new onesKeep the forks at the lowest position while not in use, and keep piston rods lubricated in timeAdjust nut(2-4) or adjusting screw(2-6)
4	Oil leakage	Seals damagedParts damaged	Replace the damaged seals with new sealsReplace the damaged parts with new parts
5	The forks descended without operation	Impurities in the oil cause the valve to be unable to close tightlySeals damagedAdjusting nut(2-4) or adjusting screw(2-6) in wrong positions	Change hydraulic oilReplace the damaged seals with new sealsAdjust nut(2-4) or adjusting screw(2-6)

Note: Do not attempt to repair the pallet truck unless you are trained in the professions.

If the truck has to be transported for a long distance, it should be packed in the wooden pallet in order to avoid collision during transportation.

The handle shall be detached before loading the truck.
The handle should be fixed stably in case sliding and damages and transported by fork truck or crane.
Before shipment, the operator should first check the truck weight, in order to choose the right crane. When the truck is unloaded, the operator shall look out for safety around to ensure slow landing of the truck.
If the truck is transported with the forklift truck, the forklift shall lift and lower it slowly to keep the balance of the truck.
The truck shall be commissioned according to the following function tests: steering, traveling, braking and combined functions with rated capacity.
- When a truck is inoperative, the cargoes (if applicable) shall be removed with proper tools, the truck shall be transported out of the working zone with a proper way.
- When the truck will be shut down and in storage for a long time, the storage environment shall be kept dry and clean, with forks lowered to their lowest position.

Technical line drawing of a mechanical transmission system with a tractor and conveyor (no text or symbols)

Parts list · Frame(85)

E20V Series Scale Pallet Trucks

Eoslift

NO.	Parts number	Description Qty.	Qty.
1	WC02000197	Frame (560 x 1150), 5012	1
	WC02000207	Frame (805 x 1220), 5012
2	WC02000204	Metal protective shell (L20V), 5012	1
3	WC04000001	ValueScale button assembly	1
4	WC04000002	ITA pressure segment ITA assembly, rail length (10cm)	2
5	WC01000006	Cylinder assembly, galvanized	1
6	WC02000194	Left push rod (580 x 1150), 5012	1
	WC02000208	1 c ^2 push rod (885 x 1220), 5012
7	WC02000193	Right push rod (560 x 1150), 5012	1
	WC02000206	Right push rod (685 x 1220), 5012
8	WC02000006	Small wheel roller, black	2
9	WC02000007	Rucker, galvanized	4
10	WC02000111	Wheel shaft, galvanized	4
11	WC02000160	Iron-core 70-well #74 x 70, brighted Ni, block iron core	4
	WC02000170	Nylon wheel #74 x 70, white
12	WC02000013	Long shaft(1540)	1
	WC02000082	Long shaft(885)
13	WC02000005	Connecting rod assembly (510), black	1
	WC02000205	Connecting rod assembly (885), black
14	WC02000022	Gas275,200, groove bell bearing 5004, two side shidded	12
15	WC02000010	Push rod connecting short, galvanized	2
16	WC02000198	Shall	2
17	WC02000196	Washer, galvanized	4
18	WC02000076	Washer	6
19	WC02000019	Ji37940.4, Push-fit type groove nipore 5	3
20	WC02000018	Connecting bracket, galvanized	1
21	WE05000002	Gas8-9.1,8mm type straight air #x26, forbending	2
22	WE05000003	Gas8-9.1,8mm type straight air #x26, forbending	6
23	WC03000001	OP879.1,8mm type straight air #x89, forbending	10
24	WC02000024	Sliding bearing 29x25x25	2
25	WC02000025	Sliding bearing 18x16x16	4
26	WC02000027	Gj33452.1,0-ring g5x1.8	1
27	WC02000028	Ji39402, 7kg hydraulic grease nipole 48	1
28	WC02000028	GE301, thrust ball bearing 51111	1

NO.	Parts number	Description
29	WC02000020	Cb305, Steel ball S18	1
30	WC02000003	GJ894.1,Cnclip for shaft 52,blackening	1
31	WC02000015	Dual cover, galvanized	1
32	WC02000012	Loll pin 2, galvanized	2
33	WC02000014	Loll pin, galvanized	2
34	WC02000190	Connecting basic, galvanized	2
35	WC02000002	GJ894.1,Cnclip for shaft 16,blackening	2
36	WLC0300001	GB701, Leagon stone, tied cap screw MG x 18, galvanized	1
37	WLC0300001	GJ894, normal type spring lock washer 6, galvanized	1
38	WC03000008	GJ501, Leagon stone, tied cap screw Mx416, galvanized	2
39	WC03000007	GB701, Leagon stone, tied cap screw M1245, galvanized	8
40	WLC03000006	GJ894, normal type spring lock washer 12, galvanized	8
41	WC02000191	Fork power(550 x 1150), 50' 2	1
	WC02000206	Fork power(585 x 1220), 50' 2
42	WC02000202	Bowl-shaped concave washer for sensor	4
43	WC02000198	Bowl-shaped convex washer for sensor	4
44	WC02000201	Screw, M12 x 80	4
45	WE07000001	GJ893.1,Cnclip for hole 25,blackening	2
46	WC02000199	Aluminum-core FU shealed(80x50, bright red 70)	2
	WC02000078	Nylon sheel φ180 x 50, white
47	WC02000017	Big wexer shaft, galvanized	1
48	WE07000004	GJ894.1,Cnclip for shaft 20,blackening	2
49	WC02000016	Big wexer cover, black	2
	WC02000076	Big wexer cover, white
50	WE06000004	GJ894, Lending type x slight pin 8x5, blackening	1
51	WC02000001	Connecting shaft, galvanized	1
52	WC02000003	I angle, black	1
53	WC02000200	Iron cable clip	2
54	WC02000107	R tape cable clip0.5	2
55	WLC03000006	GJ894, Pan lead screw finl cross records MG x15,galvanized	8
56	WLC03000004	GJ895,Plain washer 5,galvanized	4
57	WE03000004	GJ895,Plain washer 5,galvanized	2
58	WC02000774	Washer 50 x 31.8 x 3.6	4

Parts list · Frame(85) Parts list · Frame(75)

E20V Series Scale Pallet Trucks

Eoslift

Technical diagram of a mechanical assembly with numbered components and exploded views

NO.	Parts number	Description	Qty.
1	WC02000851	Frank, 5012	1
2	WF00000001	GB32.1, Heasger posted head and screw M6 x 16, galvanized	1
3	WC05000001	GB32, Normal type spring lock washer & gasket	1
4	WC02000204	Metal protective shell (F20V), 5012	1
5	WC04000001	ValueScanb out fl assembly	1
6	WC02000200	Iron cable clip	2
7	WC02000197	R type cable slide 6.5	2
8	WF00000006	GB010, For head soes will cross rows M6x 2 galvanized	6
9	WC04000002	Pressure sensor	4
10	WC03000007	GB32.1, Heasger posted head and screw M12x35, galvanized	6
11	WC05000006	GB32, Normal type spring lock washer 12, galvanized	6
12	WC01000011	Cylinder assembly, galvanized	1
13	WC02000020	GB30S, Steel ball S15	1
14	WC02000028	GB301, thrust ball bearing S1111	1
15	WF07000003	GR894.1,Circlip for shaft 52,blackoning	1
16	WC02000015	Dual issues, galvanized	1
17	WC02000018	Connecting bracket, galvanized	1
18	WC02000205	Connecting rod assembly, black	1
19	WF07000001	GR893.1,Circlip for hub 28,blackoning	2
20	WC02000024	Sliding bearing 28 × 26 × 25	2
21	WC02000025	Sliding bearing 18 × 16 × 15	4
22	WC02000082	Long shaft	1
23	WF06000003	GB32.1,Spring type straight sh SaCR, blackening	4
24	WC02000014	Bolt pin, galvanized	2
25	WC02000199	Aluminum-cora flu wheel 18 × 50 , gray metal FU	2
	WC02000078	Nylon wheel 180 x 50, white
26	WC02000022	GB27.0,boop groove ball casing G26- two slide dts class	10
27	WC02000015	Big wheel cover, block	2
	WC02000076	Big wheel cover, white
28	WC02000017	Big wheel shaft, galvanized	1
29	WS07000004	GB90H.1,Circlip for shaft 20,packening	2
30	WC06000004	GB32.1,Spring type straight sh 5x45, accelerating	1
31	WC02000136	Washer, galvanized	4
32	WC02000816	Small wheel carrier, block	2

Parts list · Frame(75)

E20V Series Scale Pallet Trucks

Eoslift

NO.	Parts number	Description	Qty.
33	WC02000010	Push rod connecting shaft, galvanized	2
34	WC02000850	Right push rack, 5012	1
35	WC02000849	Left push rack, 5012	1
36	WC02000019	JU7910,4, Pull-fit type grease ripple B	3
37	WL06000002	60/701, spring type straight pin 6x200, fastening	2
38*	WC02000073	Single wheel shaft, galvanized	2
39	WC02000180	Cunning base, galvanized	2
40	WC02000012	Lack pin 2, galvanized	2
41	WL07000002	CR894.1,Cindip for shell 18,blackening	2
42	WC06000001	CR879.1, spring type straight pin 5x30, fastening	10
43	WC02000195	Shatt	2
44	WC02000004	Connecting shaft, galvanized	1
45	WC02000075	Washer	4
46	WC02000218	Fork cover, 5012	1
47	WC02000003	Handle, block	1
48	WC02000027	CH3452.1,O-ring 5×1.8	1
49	WC02000026	JE7943.2, Ingle hydraulic gross ribcic M6	1
50	WC02000917	Screw, M12 × 40	4
51	WE05000004	GB95,Jair washer, 5-govanized	5
52*	WC02000074	Iron-cane full wheel 74 × 33, right disc full block for core	2
	WC02000118	Nylon wheel 74 × 93, white
53	WC03000009	CR76.1, Foamer socket head screw N4×10, galvanized	2
54	WC02000160	Iron-cane full wheel 74 × 70, knock disc full block for core	2
	WC02000120	Nylon wheel 74 × 70, white
55	WC02000007	Rocker, galvanized	2
56	WC02000011	Wheel shaft, galvanized	2
57*	WC06000001	CR879.1, Spring type straight pin 5x37, blackening	2
58*	WC02000075	Washer	4
58*	WC02000022	GB876 Glass groove ball bearing GB94, two disc blocks	4

Note: Marked with "2" are single wheel parts

Technical diagram of a mechanical assembly with numbered components and exploded view

Parts list·Cylinder

E20V Series Scale Pallet Trucks

Eoslift

NO.	Parts number	Description	Qty.
1	WCC2000176	Valve body weced,75l, galvanized	1
	WCC2000157	Valve body weced,85l, galvanized
2	WCC2000066	GR562. Combine lim suwing gears: 1.0	1
3	WCC2000038	Screw	1
4	WCC2000061	Seal ring U1535	1
5	WCC2000059	Gl3452.1.0-ringo34.5x3.55	1
6	WCC2000058	Dus proool ring TH35	1
7	WCC2000035	Platon rod	1
8	WCC2000045	Safety valve spool	1
9	WCC2000048	Pressure adjusting spring	1
10	WCC2000038	Pressure adjusting screw	1
11	WCC2000071	Gl3452.1.0-ring c11.2x2.55	1
12	WCC2000037	Screw plug	1
13	WCC2000044	Copper gasket	1
14	WCC2000039	Pump body	1
15	WCC2000064	Seal ring U1518	1
16	WCC2000063	Dus proool ring TH18	1
17	WCC2000042	Spring cover	1
18	WCC2000041	Pump core	1
19	WCC2000043	Pressure spring	1
20	WCC2000040	Pin	1
21	WCC2000049	Unlocking plate, galvanized	1
22	WCC2000005	Qa879.1,acring, type straight on a-10,placing	1
23	WCC2000003	CuTa, nominal set prices on flat joint MB x 25, galvanized	1
24	WCC4000003	GR6172.1, Helcor 71# nut MB, galvanized	1
25	WCC1000046	Integrated valve assembly	1

Exploded view diagram of a mechanical assembly with numbered components for identification

Parts list · Integrated valve

E20V Series Scale Pallet Trucks

Eoslift

NO.	Parts number	Description	Qty.
1	WC02000051	Push pin sleeve	1
2	WC02000065	GR3452.1.0-ring 15.2x2.4	1
3	WC02000067	GR3452.1.0-ring 8x1.6	2
4	WC02000053	Return valve sleeve	1
5	WC02000066	CL8452.1.0-ring 9.5x1.6	1
6	WC02000050	Stem	1
7	WC02000052	Unloading spring	1
8	WC02000054	O-ring retainer II	1
9	WC02000069	GR308,Sluck bell 57	1
10	WC02000070	Liquid inlet valve score	1
11	WL06000006	GB117, Concert taper pin 2 x 6	2
12	WC02000056	O-ring retainerI	1
13	WC02000062	GR3452.1.0-ring 13.2x2.4	1
14	WC02000048	Spring load	1
15	WL03000002	C016.0 Pin head screw with nominal recess M2×2 galvanized	1
16	WC02000058	Roast valve spool	1
17	WC02000057	Spool spring	1
18	WC02000017	Blind nut	1
19	WC02000068	GB3152.1.0-ring 21.2x2.65	1

Technical diagram of a mechanical assembly with numbered components for identification

Parts list·Handle

E20V Series Scale Pallet Trucks

Eoslift

NO.	Parts number	Description	Qty.
1	WJ10800014	Handle wideed	1
2	WJ10800015	Clamping roller	1
3	WJ10800016	Roller pin	1
4	WJ10800011	Finger grip handle	1
5	WJ10800008	Spring type pin (5)	1
6	WJ10800003	Spring type pin (6)	1
7	WJ10800004	Spring type pin (7)	1
8	WJ10800020	Locking nut	1
9	WJ10800002	Spring type pin (9)	1
10	WJ10800008	Positioning plate	1
11	WJ10800012	Connecting sheet of pull rod	1
12	WJ10800013	Pull rod	1
13	WJ10800016	Chain	1
14	WJ10800019	Adjusting bolt	1
15	WJ10800005	Spring type pin (15)	1
16	WJ10800017	Bushing	1
17	WJ10800009	Torson spring	1
18	WJ10800010	Plastic roller	1

Technical diagram of a mechanical device with numbered components for identification