CVD1471 - Wardrobe Tennsco - Free user manual and instructions

USER MANUAL CVD1471 Tennsco

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

Wardrobe Storage Cabinet Unassembled Model 1471 or CVD1471

tennsco®

Storage Made Easy

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Open beige metal cabinet with two doors open, showing internal shelves and door (no text or symbols visible)

Exterior view of a two-decker metal cabinet with glass doors and a door handle (no text or symbols visible)

LOAD CAPACITIES PER SHELF LEVEL EVENLY DISTRIBUTED
UNIT SIZE	WEIGHT CAPACITY
36w x 18d	200 lbs.

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury. For safety, wear a pair of work gloves when assembling or performing any maintenance on products.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modification or repair by persons not authorized by Seller, where goods are damaged during shipment, or where the date stamps on the goods have been defaced, modified or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER'S OPTION, AND SHALL IN NO EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the goods to Seller for inspection on Seller's premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty and are returned within the warranty period stated above.

ASSEMBLY OF 1471 or CVD1471 CABINET

Tools Needed: A free 11/32" nut driver is included with each Tennisco cabinet.

Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.

1. The reference numbers used throughout this sheet refer to the illustration on the back cover. This is to help you to identify the various parts as they are mentioned.

NOTE: All illustrations show a solid door. Assembly for C-Thru doors (CVD1471) is identical.

1. Place the cabinet back (Ref. No. 1) on a protected surface to prevent scratching the paint.

The flange on the bottom of the back should be facing upward.

k (Ref. No. 1) on a vent d. Flange faces upward.

NOTE: When bolting the unit together, leave the bolts slightly loose until Step 8, unless otherwise specified.

1. Attach the left side (Ref. No. 2) to the back by placing flange (A) around the back and bolting together with seven bolts and nuts (Ref. Nos. 19 & 20). Be sure that the lances on all shelf adjustment strips (B) are pointing in the same direction.

direction. A Flange goes under back. B All lances point UP on both backs and side. Flanges face upward

1. Attach the right side (Ref. No. 3) to the back in the same manner as you did in step 3, again, making sure that the flange is around the back and that the lances on the shelf adjustment strips are pointed in the same direction as those on the back and left side.

Isometric line drawing of a rectangular frame with internal dotted lines and red arrows indicating direction (no text or symbols)

1. Insert the shelf (Ref. No. 4) into the second lance of the side and back panels.

If (Ref. No. 4) into e of the side Inset A Use 2nd lance

1. Attach the top (Ref. No. 5) to the unit by sliding the outer flange over the back of the unit and the side flange of the side panel on the unit. The threaded studs should go through

the holes in the top lange of the side and fasten with three nuts. Attach the back to the top using four bolts and nuts. Nuts placed loosely on studs of the sill. Slide ends in to the slots on the bottom of the sides.

1. Next, attach the sill (Ref. No. 6) to the sides, as shown above. Place nuts loosely on each of the studs and slide the ends of the sill into the slots on both sides of the unit. Then, securely tighten the nuts.

2. Place the rear flange of the bottom (Ref. No. 7) into the bottom lances of the back. The flange with two holes should face the front, hanging over the sill. Insert the bolts through

the bottom and still with the head facing the front of the unit. Secure with two nuts. Tighten all bolts. Two holes must be in front Insert bottom into bottom lances.

1. Using two people, set the unit upright and attach the left coat rod bracket (Ref. No. 17) beneath the left side of the cabinet shelf by inserting one bolt through the hole in the left edge of the shelf. Secure with a nut. Attach the right bracket in the same way. Then slide the coat rod (Ref. No. 16) through the holes in the brackets.

Technical line drawing of a cabinet or enclosure with internal components and red directional arrows indicating movement (no text or symbols)

1. Attach the left door (Ref. No. 8) to the unit by placing the door on the hinges, aligning the hinge holes, and dropping the hinge pins (Ref. No. 15) into the slots. Then, tap the top of each hinge pin until fully seated.

Technical diagram of an open refrigerator with labeled door and panel, showing internal structure and red arrows indicating features.

Leveler Access Holes

1. Attach the right door (Ref. No. 9) to the unit in the same way you attached the left door.

2. The cabinet must be level in order for the doors to close properly. Levelers may be adjusted by placing the nut driver through the hole in each end of the sill and adjusting the leveling screw.

Handle/Locking System Installation

Simple line drawing of a door handle with arrows indicating direction (no text or symbols)

1. Place the locking handle (Ref. No. 11) on the right hand door and fasten with two #8-32 X 1/4 hex-head bolts and lock washers, provided with the handle.

2. Turn the handle to the open position and place the locking cam (Ref. No. 12) over the square shank of the door handle. The latch must be facing downward as shown. Then place the locking cotter pin (Ref. No. 13) through the hole of the square shank.

Technical diagram showing a hand tool and a crimping tool assembly with labeled parts and directional arrows

1. With the handle still in the open position, hook the locking bars (Ref. No. 10) to the locking cam (see "A" at left). Once in position, slowly rotate the door handle to the closed position so the lock bars prot rude from the holes at the top and bottom of the door (shown at right, below).

Line drawing of a door handle with lever and handle (no text or symbols)

1. Slide the nylon lock bar guide inserts (Ref. No. 14) over the lock bar ends and through the door slots (see "B" at right). Push down firmly until the guides snap into place.

Line drawing of a door with a small object on the side, labeled B (no text or symbols present)

REPLACEMENT PARTS

Left Side (Ref No. 2) Top Top (Ref No. 5) Hinge Pins (Ref No. 15) Shelf (Ref No. 4) Back Panel (Ref No. 1) Coat Rod Bracket (Ref No. 16) Coat Rod (Ref No. 17) Right Side (Ref No. 3) Left Door (Ref No. 8) SIII (Ref No. 6) Bottom (Ref No. 7) Right Door (Ref No. 9) Tennisco Nut Driver (Ref No. 18) Locking Bar Guide Nylon Insert (Ref No. 14) Cotter Pin (Ref No. 13) Locking Handle with Keys (Ref No. 11) Locking Cam (Ref No. 12) Locking Bar Set (Ref No. 10)

REF. NO.	DESCRIPTION	QTY.	PART NO.
1	Back Panel	1	944BA
2	Left Side	1	944LS
3	Right Side	1	944RS
4	Shelf	1	301
5	Top	1	944TO
6	Sill	1	944SIN
7	Bottom	1	292BO
8	Left Door: Solid for 1471	1	944LD
	Left Door: C-Thru for CVD1471 (not shown above)	1	CVD-72LD
9	Right Door: Solid for 1471	1	944RD
	Right Door: C-Thru for CVD1471 (not shown above)	1	CVD-72RD
10	Locking Bar Set	1	944LB
11	Locking Handle w/keys & hardware	1	944LH
12	Locking Cam*	1	944LC
13	Cotter Pin*	1	CTRPN
14	Locking Bar Guide Insert (Nylon)*	2	944GI
15	Hinge Pins* (not shown above)	6	944HP
16	Coat Rod	1	045CR
17	Coat Rod Bracket	2	045RB
18	Tennsco Nut Driver	1	TOOL-2
19	#8-32 x 38 " bolts (not shown above)	20	**
20	#8-32 nuts (not shown above)	30	**

*Included in Ref. No. 11, locking handle with keys and hardware (Part No. 944LH).
**Available Locally

NOTE: Additional hardware may be included for replacement purposes.

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged. However, should your unit contain missing or damaged parts, please contact your purchase location.