JX9152EJES - Microwaves GE - Free user manual and instructions

Product Type	Countertop Microwave Oven
Brand	GE
Model	JX9152EJES
Color	Stainless Steel
Capacity	1.5 cu. ft.
Power Output	1500 Watts
Power Supply	120 V / 60 Hz
Dimensions (W x H x D)	21.5 x 12.5 x 18.0 inches
Weight	Approx. 50 lbs
Control Type	Electronic Touchpad
Display	LED Digital
Turntable	Glass Turntable (removable)
Interior Light	Yes
Child Lock	Yes
Clock & Timer	Yes
Cooking Modes	Popcorn, Beverage, Potato, Pizza, Reheat, Defrost, Sensor Cooking
Number of Power Levels	10
Cleaning Instructions	Wipe interior and exterior with damp cloth; do not use abrasive cleaners
Spare Parts Availability	Turntable, roller ring, fuse, door switch (contact GE Appliance Parts)
Repairability Index	7/10 (common parts available, professional repair recommended)
Certifications	UL Listed, FCC compliant

Frequently Asked Questions - JX9152EJES GE

How do I set the clock on my GE JX9152EJES microwave?

Press the Clock button, enter the time using the number pad, then press Clock again or Start to confirm.

What is the proper way to clean the microwave interior?

Unplug the microwave. Use a damp cloth with mild soap to wipe the interior. Avoid abrasive cleaners or scouring pads. Dry with a soft cloth.

Why does my microwave display 'Error' code?

Error codes may indicate a power surge or control board issue. Unplug for 60 seconds, then plug back in. If persists, contact GE support.

Can I use metal pans in this microwave?

No, metal can cause arcing and damage. Use only microwave-safe glass, ceramic, or plastic containers.

How do I enable the child lock feature?

Press and hold the Stop/Cancel button for 3 seconds until you hear a beep and LOCK appears on the display. Repeat to unlock.

What is the recommended container for popcorn mode?

Use a microwave-safe popcorn popper or a bag designed for microwave popcorn. Follow package instructions.

How do I adjust the cooking time while the microwave is running?

Press the Time Cook or Number Pad to add time (up to 99 minutes 99 seconds), then press Start. You can also press Add 30 Seconds.

The turntable is not rotating. What should I do?

Check if the turntable is properly seated on the roller ring. Remove any obstructions. If still not rotating, the motor may need replacement.

What does 'Sensor Cooking' mean?

Sensor Cooking uses a humidity sensor to automatically adjust cooking time and power for optimal results. It's great for reheating leftovers.

Where can I find the model number and serial number?

The model number and serial number are on a label on the back or side of the microwave. Record them for service.

USER MANUAL JX9152EJES GE

Installation Instructions

Microwave Oven Built-In Trim Kits

JX9152 and JX9153

Questions? Call GE Appliances Answer Center at 800.626.2000 or Visit our Website at: GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT — Save these instructions for local inspector's use.
• IMPORTANT — Observe all governing codes and ordinances.
• Note to Installer – Be sure to leave these instructions with the Consumer.
• Note to Consumer – Keep these instructions for future reference.
• Skill level – Installation of this appliance requires basic mechanical and electrical skills.
  • Completion time – 1 to 3 hours
  • Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
• This kit is for use on models:PEB9159DJ, PEB9159SJ, PEB9159EJ, CEB1599SJ.and CEB1599EL.
• This kit and microwave are approved for installation alone or above any single electric wall oven. Do not mount adjacent (within 2 feet) to any range, cooktop, gas oven, or other microwave.
  • This product is to be installed 3 feet above floor level.
• Do not alter or modify any part of this kit or the oven.
• For easier installation and personal safety, we recommend that two people install this microwave oven.
• Unplug the microwave oven before attempting installation of this kit.

WARNING

— This oven must be plugged into a

properly grounded 3-hole, 120 volt receptacle as required by the National Electrical Code.

WARNING

— Before beginning the installation,

switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

PARTS INCLUDED

PART QUANTITY
	Rear Duct 1
	Bottom Duct	1
	Trim Kit Frame	1
	Rail	2
[032Z]	Short Screws	16 required3 extra
	Long Wood Screws 4 required2 extra

NOTE: This kit has extra screws to prevent the technician from spending extra time locating a replacement in case they lose one during installation.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

WARNING

Improper use of the grounding plug can result in a risk of electric shock. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.

Permanent and Correct Installation

3-Prong plug Grounding pin 3-Prong receptacle Grounded receptacle box

ELECTRICAL REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 14 amps and 1.60 kilowatts. This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating. The power supply cord and plug should be brought to a separate 15 to 20 ampere branch circuit single grounded outlet. The outlet box should be located in the cabinet above the oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.

TOOLS YOU WILL NEED

■ 2 Phillips Screwdrivers (#1 & #2) ■ Pencil ■ Level ■ Drill with 3/32" Drill Bit ■ Tape Measure

CUTOUT DIMENSIONS

Dimen-sion	Trim Kit		Cutout
	27” 30”
Height 19	^1/_8 ” 19	^1/_8 ” 17	^1/_8 ± ^1/_8 ”
Width 26	^7/_8 ” 29	^3/_4 ” 23	^1/_4 ± ^1/_8 ”

Min. depth with receptacle outside cutout - 22" Min. depth with receptacle inside cutout - 23 12 " 120 volt - 60 Hertz grounded power receptacle.

1" Overlap Depth 27"models: 1 7/8" overlap 30"models: 3 5/16" overlap Height Width 1" Clearance beyond trim frame (on all sides) 1" Overlap 3" Min.

Bottom of trim kit must be minimum of 36" from floor

WARNING

— This trim kit uses air flow from the top, bottom and sides of the trim frame. Blocking the air flow can cause the microwave to function improperly and may cause damage to the microwave.

Allow a 1" clearance beyond the edge of the trim kit frame to provide proper air flow.

FOR INSTALLATION ABOVE A BUILT-IN OVEN:

Microwave oven should be installed on a 3/8" plywood base and supported by 2x4 or 1x2 equivalent runners on all sides. Base must be capable of supporting a minimum of 100 lbs.

1 LOCATE AND INSTALL THE BASE PAN

Set Base Pan into the front cabinet microwave oven cutout and center it right and left. Push back until the front flange is against the cabinet front wall.

Mount the Base Pan using 3 short screws.

Mount the Base Pan using 3 short screws. Short Screw Base Pan Mounting Holes

2 INSTALL THE RAILS

Disconnect the microwave oven from the receptacle. Remove everything out of the microwave oven, including packing, Owner's Manuals, turntable and turntable support. A protective film has been applied to some microwave oven and trim kits. If applied, remove the film. Turn over the microwave oven and secure the rails to oven Base Plate by inserting 4 short screws. Be careful not to scratch the microwave oven.

Microwave Oven Bottom Rail Short Screw A Flanges Door

3 INSTALL THE REAR DUCT

1. Gently return microwave oven to its upright position.
2. Remove screw A.

Screw A

1. Align the rear duct with the back of microwave oven, as shown.

Diagram of a microwave oven with an open lid and ventilation slots, showing internal structure and airflow direction (no text or symbols)

1. Slide 2 tabs into the slots on the right side of the back of microwave oven.

A Door duct tab B

A. Rear duct tabs

B. Slots

1. Use 2 short screws to secure top of rear duct to the back of microwave oven, as shown.

A B C

A. Short screws (2)

B. Rear duct

C. Back of microwave oven

3 INSTALL THE REAR DUCT (continued)

1. Use 3 short screws to secure back of rear duct to the back of microwave oven, as shown.

wave over, as shown. A B C

A. Short screws (3)
B. Rear duct
C. Back of microwave oven

Plug the power cord into the wall receptacle. Slide the microwave oven assembly gently into the cabinet, using care not to pinch the power cord. Be sure to keep the assembly centered as it slides back to where the tongue of the rails goes through the slots on Base Plan. The top edges of the Base Plan should now be centered right to left in the opening. The Base should be tight against the cabinet.

Rail Guides Rails

5 CHECK LEVELING

Check the leveling by placing a level at the front and sides of the microwave. It may be necessary to add wood shims under the base pan to level the microwave front-to-back and side-to-side.

Line drawing of a microwave oven with hands operating the lid (no text or symbols)

6 SECURE THE RAILS TO THE CABINET

Ensure the Base Pan and Bottom Bracket front flanges are tight against the cabinet, and that the screws holes are aligned. Drive 4 short screws through the Base Pan and Rails into the cabinet

Mounting Holes

Short Screw

7 INSTALL THE TRIM KIT FRAME

1. Position the assembled Trim Kit frame around the oven.
2. Drill pilot holes using the drill (3/22).
3. Secure the Trim Kit by 4 long screws through the trim kit into the cabinet by using a manual screw driver.

IMPORTANT-

— Start all screws before tightening any one screw. Do not overtighten screws since it can cause misalignment of top/side strips.

Long Screw

8 REPLACE ANY LOOSE ITEMS

1. Your trim kit is now fully installed. Replace the turntable and turntable support that was removed from inside the microwave oven.
2. Keep these installation instructions and extra screws for future reference and need. Do not place them in the microwave oven.
3. Replace the house fuse, or close the circuit breaker to restore power at the service panel.

DE68-03364A

49-40762-2

06-17 GEA

Printed in China

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

Diagram of a microwave oven with ventilation slots and an open door, showing airflow direction (no text or symbols)

Technical line drawing of a mechanical component with labeled points A and B (no text or symbols beyond labels)

A B C

Riel Guías Rieles

Line drawing of hands operating a microwave oven with control knobs (no text or symbols)

6 ASEGURE LOS RIELES AL GABINETE

Short Screw