SL-S212-RAQ - Alarm Enforcer - Free user manual and instructions

USER MANUAL SL-S212-RAQ Enforcer

Five different types of LED strip designs arranged horizontally, each with a unique color and pattern (no text or symbols visible)

LED Color	Model
Red	SL-S212-RAQ
White	SL-S212-WAQ
Blue	SL-S212-BAQ
Yellow	SL-S212-YAQ

• Flexible LED Strip easily installs anywhere.
• Self adhesive backing for easy installation.

ENFORCER® Flexible LED Strip

Overview:

The SL-S212 series of ENFORCER Flexible LED Strips provides energy efficient illumination in a flexible package, perfect for a wide variety of indoor lighting applications. The lightweight Flexible LED Strips can be placed anywhere, trimmed to length and output only minimal heat.

Specifications:

Operating voltage		12VDC
Current draw per LED Strip		200mA@12VDC
Current draw per 3-LED segment		50mA@12VDC
Dimensions		12^^7/_15^ (305x10 mm)
Number of LEDs per strip		12
Distance between LEDs		1" (25mm)
LED color	SL-S212-RAQ	Red
	SL-S212-WAQ	White
	SL-S212-BAQ	Blue
	SL-S212-YAQ	Yellow
Operating temperature		-5^ - 115^ F ( -20^ - 45^ C)
Weight		0.4-oz (11.4g)

Installation:

WARNINGS:

▲ THE SL-S212 FLEXIBLE LED STRIP IS FOR INDOOR USE ONLY AND SHOULD NOT BE EXPOSED TO MOISTURE. WEATHER OR HIGH HUMIDITY.

⚠ DO NOT FOLD STRIP. DO NOT BEND STRIP REPEATEDLY OR INSTALL IN SUCH A WAY THAT MAY CAUSE STRIP TO BEND REPEATEDLY. DAMAGE MAY RESULT.

- Mounting:

1. The LED Strip can be mounted anywhere using the self adhesive mounting strip on the back.
2. For installations where use of the adhesive strip is not practical or not applicable, use another fastener such as optional SL-SAS-SH1Q Strip Fastener (sold in packs of 10).
   NOTE: When mounting, do not pierce the LED Strip, as internal circuitry may be damaged.

• End Caps: (Optional—Sold in packs of 10)

1. For protection against accidental short circuit, dust and water, place optional SL-SAS-EC1Q End Cap over the unconnected end of the LED Strip.

2. For further protection, seal end cap with silicon sealant.

NOTE: Sealing the end cap will increase the water resistance of the LED Strip but will not

ENFORCER® Flexible LED Strip

1. The following ENFORCER 12VDC Power Supplies are ideal for use with the LED Strip:

Power Supply Model	Max. Supply Current	Number of Strips
ST-UV12-S0.5Q	0.5A	up to 2
ST-UV12-S1.0Q	1.0A	up to 4
ST-UV12-S2.0Q	2.0A	up to 9
ST-UV12-S3.0Q	5.0A	up to 24

- Wiring

1. Each LED Strip has a female pin connector at each end and one included 4-pin adapter.
2. Connect the 4-pin adapter to either end of the LED Strip.
3. Use the optional SL-SAS-PC1Q Power Connector (2.1mm) to connect the LED Strip to a power adapter. Use a CA-161T DC Plug to Removable Terminal Block adapter if required

1. If use of SL-SAS-PC1Q is not desired, the LED Strip pin connections are as follows:

1. If at any time the strip fails to illuminate when power is connected, it is likely that the pins have been reversed. Flip the power connector over or reverse the power connections to correct the problem. The product is reverse polarity protected and damage will not result.

- Connecting Multiple Units (max. 30 strips)

1. Up to 30 LED Strips can be connected together in series.

LED Strip 4-pin adapter (one included) LED Strip

1. If any strip fails to illuminate when power is connected, flip end for end to reverse polarity.
2. The LED Strip is reverse polarity protected so inverse connection will not cause damage.

WARNING: DO NOT CONNECT MORE THAN 30 LED STRIPS IN SERIES.

Cutting the LED Strip:

1. The LED Strip can be cut to length every 3 LEDs using wire cutters, tin snips or strong scissors.
2. At any of the points shown below, cut as close to the mid-point between the LEDs as possible.
3. If desired, the cut end may be covered with electrical tape or silicon sealant.
4. Connect the shortened strip to the power supply. No further electrical connections are needed.

ENFORCER® Flexible LED Strip

Brightness	Number of pins	Connection Diagram
Maximum	Connect all +12VDC pins
Medium	Connect two +12VDC pins
Minimum	Connect one +12VDC pin

Recommended Accessories:

LED End Cap

Sold in packs of 10

LED Strip Fastener

Sold in pecks of 10

LED Power

Connector

DC Plug Adapter

w' Terminal Block

DC Jack Adapter

Removable Terminal Block

SL-SAS-EC1Q

SL-SAS-SH1Q

SL-SAS-PC1Q

CA-161T

CA-151R

Also Available from SECO-LARM:

LED Strobe Light

SL-1301-BAQ Series

SL-1311-MA

52 LED Disk Module

SL-1302-MA

WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM's obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or alteration, Improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship. The sole obligation of SECO-LARM, and the purchaser's exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM's option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else.

NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is one of continual development and Improvement. For this reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible for any rights to cross-renewable or