MW19C - Video projector Barco - Free user manual and instructions

USER MANUAL MW19C Barco

Black rectangular projector with a lens and control panel, no visible text or symbols on the device itself.

Product revision

Software Revision: 2.2

Copyright ©

All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

Changes

Barco provides this manual 'as is' without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication.

The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site https://www.barco.com/en/signin.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers.

Product Security Incident Response

As a global technology leader, Barco is committed to deliver secure solutions and services to our customers, while protecting Barco's intellectual property. When product security concerns are received, the product security incident response process will be triggered immediately. To address specific security concerns or to report security issues with Barco products, please inform us via contact details mentioned on https://www.barco.com/psirt. To protect our customers, Barco does not publicly disclose or confirm security vulnerabilities until Barco has conducted an analysis of the product and issued fixes and/or mitigations.

Patent protection

Please refer to www.barco.com/about-barco/legal/patents.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during

Disclaimer on GUI images used in this manual

The GUI images in this manual are example illustrations and should be treated as such. While the name of the projector displayed in the illustrations may be different from the projector model you are currently using, the menu lay-out and functionality is identical.

Disclaimer for camera usage

Barco provides a kit with a laser range finder and USB camera to help measure the distance from the front of the projector to the projected surface and to help monitor the performance of the projector. Barco disclaims any liability for any use of the USB camera outside this intended use.

Disclaimer for network usage

Barco highly recommends to install the projector in a closed network environment to minimize the risk of leaking, hacking or corrupting of company confidential information; commercial sensitive information and/or personal data. Furthermore, strengthen your network security to protect the projector against unauthorized access by third parties. To the maximum extent permitted by law, Barco disclaims any liability for the use of the projector in an open network environment.

Table of contents

1 Safety information 9

1.1 General Considerations 10

1.2 Important safety instructions....11

1.3 Product safety labels....15

1.4 High Brightness precautions: Hazard Distance 16

1.5 HD for fully enclosed projection systems....18

1.6 HD in function of modifying optics 19

1.7 Radio equipment (optional) 20

1.8 Compliance 20

1.9 Download Product Manual 20

2 Getting Started 21

2.1 Getting to know the projector 22

2.2 Power on the projector 24

2.3 Start image projection 25

2.4 Switching to ready mode 28

2.5 Power off projector 28

4.6 Pulse Quad Combo input Mk II 43
4.7 Pulse Quad Combo input Mk I 44
4.8 Pulse Quad DP 1.2 input 45
4.9 Pulse SFP input 46

5 GUI - Introduction....47

5.1 Overview 48
5.2 Navigation 51
5.3 Test Patterns 53

6 GUI – Source 55

6.1 Displaying a single source 56
6.2 Displaying multiple sources: Stitched layouts....56
6.3 Connector Settings 58

7 GUI – Image 61

7.1 Setting image levels manually 62
7.2 Adjusting the sharpness 63
7.3 Adjusting the gamma correction 64
7.4 Setting the desired Gamma type....65
7.5 Digital Shift & Zoom 67
7.6 RealColor P7 71
7.7 Displaying HDR content 73
7.8 Dynamic contrast 74

8 GUI – Installation 77

8.1 Configuring the lens, optical zoom-focus 78
8.2 Configuring the lens, shift 78
8.3 Configuring the lens, dynamic focus 79
8.4 Configuring the lens, Shift to center 80
8.5 Configuring the lens, tilt sensor 81
8.6 Laser ranging 82
8.7 Manipulating the rigging frame 83
8.8 Manipulating the ringing frame center position 85

8.14.3 Connection possibilities....112

8.14.4 3D Setup....113

9 GUI – Profiles 115

9.1 Profiles introduction 116

9.2 Profiles setup parameters....116

9.3 Saving settings to a new profile 117

9.4 Deleting a projector profile....119

10 GUI – System Settings 121

10.1 Remote control 122

10.1.1 Broadcast address 122

10.1.2 Projector address....122

10.1.3 IR sensors 123

10.2 Host name - custom projector name setup.... 124

10.3 Communication, LAN setup 125

10.3.1 Introduction to a Network connection 125

10.3.2 Wired IP address set up 126

10.3.3 Wireless IP address set up 128

10.3.4 LAN over HDBaseT™ IP address set up 131

10.4 DMX....133

10.5 Front XLR output voltage control 135

10.6 GSM configuration....135

10.7 Changing the User Interface language 136

10.8 Themes....137

10.9 Units (measurement) system setup 138

10.10 Controlling the backlight of the LCD Display 138

10.11 Date and time setup - manually 139

10.12 Date and time setup - automatically 140

10.13 Power saving settings 142

10.14 Lens features.... 143

10.15 Factory reset....144

10.16 Lens Calibration.... 148

40.47 Flanbakhness 440

13.2 Cleaning the lens 171
13.3 Cleaning the exterior of the projector....172
13.4 Cleaning / replace the air filters.... 172

A Specifications 177

A.1 Specifications SDI inputs....178
A.2 Specifications HDMI inputs 178
A.3 Specifications HDBaseT inputs....179
A.4 Specifications DisplayPort 1.2 inputs 180
A.5 Specifications SFP inputs 181

B Video timing tables 183

B.1 Overview video timings....184
B.2 Overview video timings SDI Inputs 185
B.3 Overview video timings HDMI 2.0 inputs....186
B.4 Overview video timings DisplayPort 1.2 inputs 188
B.5 Overview video timings HDBaseT inputs 190

C DMX chart 193

C.1 DMX chart input board positioning 194
C.2 DMX chart, Basic 194
C.3 DMX chart, Extended 195

D WiFi & GSM compliance information 199

D.1 Compliance FCC 200
D.2 Compliance IC 200
D.3 KCC Certification....201

E Regulatory information 203

E.1 Product compliance 204
E.2 China RoHS compliance....205
E.3 Taiwan RoHS compliance 206
E.4 Turkey RoHS compliance....207
F.5 Disposal information 207

Safety information

1

1.1 General Considerations 10
1.2 Important safety instructions....11
1.3 Product safety labels....15
1.4 High Brightness precautions: Hazard Distance....16
1.5 HD for fully enclosed projection systems....18
1.6 HD in function of modifying optics 19
1.7 Radio equipment (optional) 20
1.8 Compliance....20
1.9 Download Product Manual 20

About this document

Read this document attentively. It contains important information to prevent personal injury while installing and using the UDM projector. Furthermore, it includes several cautions to prevent damage to the UDM projector. Ensure that you understand and follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing the UDM projector.

Safety information

1.1 General Considerations

WARNING: Be aware of suspended loads.

WARNING: Wear a hard hat to reduce the risk of personal injury.

WARNING: Be careful while working with heavy loads.

WARNING: Mind your fingers while working with heavy loads.

WARNING: In case of optical radiation emergency, please disconnect the device from the mains current; this by employing the mains switch. In case the mains switch is not easily accessible, the projectors shall be disconnected by other means for example the mains junction box. It is advised to employ the shutter or select a black image on the projector in order to reduce the risk of the emergency.

General safety instructions

• This product contains no user serviceable parts. Attempts to modify/replace mechanics or electronics inside the housing or compartments will violate any warranties and may be hazardous.
• Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.
• Before operating this equipment please read this manual thoroughly and retain it for future reference.
  • Installation and preliminary adjustments must be performed by qualified Barco personnel or by authorized Barco service dealers.
• All warnings on the projector and in the documentation manuals must be adhered to.
• All instructions for operating and use of this equipment must be followed precisely.
• All local installation codes should be adhered to.

Notice on safety

Safety information

CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Notice on laser radiation

The laser distance meter that is optional equipment for this projector can emit a class 2 laser ranging beam of 0.95 mW / 638 nm. When installed correctly, this distance meter is located on the front side of the projector (see ). The laser beam can be enabled by either pressing the button on the equipment, via the projector menu, or via the projector software. Thermal retinal eye injury is possible when staring into the laser ranging beam.

Image 1-1

WARNING: Laser Radiation — Do not stare into laser ranging beam, Class 2 IEC EN 60825-1:2014 See the product safety manual for details.

Users definition

Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having appropriate technical training and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize the potential risk to themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE PERSONNEL, AUTHORIZED to operate professional projection systems.

The UDM projector is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential hazards associated with high voltage, high intensity light beams and high temperatures generated by the light source and associated circuits. Only qualified SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service functions inside the product enclosure.

1.2 Important safety instructions

Safety information

• Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
• If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated for less amperage than the projector may overheat.
• Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electrical shock.
• Make sure that no objects enter into the vents and openings of the set.
• Do not expose this projector to rain or moisture.
  • The projector is designed for indoor use only. Never operate the unit outdoors.
• Do not immerse or expose this projector in water or other liquids.
• Do not spill liquid of any kind on this projector.
• Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before resuming operations.
• Do not disassemble this projector, always take it to qualified service personnel when service or repair work is required.
• Do not use an accessory attachment which is not recommended by the manufacturer.
• Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.

To prevent personal injury

• To prevent injury and physical damage, always read this manual and all labels on the system before powering the projector or adjusting the projector.
• To prevent injury, take note of the weight of the projector. The weight of a basic projector is about 48 kg (105 lb) without lens.
• To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
- Warning: high intensity light beam. NEVER look into the lens! High luminance could result in damage to the eye.
- Warning: extremely high brightness projector: This projector embeds extremely high brightness (radiance) lasers; this laser light is processed through the projectors optical path. Native laser light is not accessible by the end user in any use case. The light exiting the projection lens has been diffused within the optical path, representing a larger source and lower radiance value than native laser light. Nevertheless the projected light represents a significant risk for the human eye when exposed directly within the beam. This risk is not specific related to the characteristics of laser light but solely to the high thermal induced energy of the light source; which is comparable with lamp based systems. Thermal retinal eye injury is possible when exposed within the Hazard Distance. The Hazard Distance (HD) is defined from the projection lens surface towards the position of the projected beam where the

- Do not stack or hang projectors without using the stacking frame.

• Max units in stacked configuration, 3 units.

- Max units in hanging configuration, 2 units.

- When hanging projectors on a truss with the Barco stacking frame, always secure the stack with safety cables between the projectors and the truss.

- When using the projector in a hanging configuration, always mount 2 safety cables. See installation manual for the correct use of these cables.

- Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and possible injury to the user.

- Only place the projector on a stable surface, or mount it securely using an approved ceiling mount rig.

- It is hazardous to operate without lens or shield. Always switch the output light off when replacing a lens.

- Lenses or shields shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.

- Cooling liquid circuit. The projector contains a cooling circuit filled with Mono-ethylene glycol (1,2-ethane diol) and inhibitors in aqueous solution (34% active). If the unlikely event that the cooling circuits have a leak, switch off the device and contact qualified service personnel. The liquid is not for household use. Keep out of reach of children. Harmful by oral intake. Avoid exposure to pregnant women. Avoid contact with eyes, skin and clothing. Avoid inhale of the noxious fumes.

- Never point or allow light to be directed on people or reflective objects within the HD zone.

- All operators shall have received adequate training and be aware of the potential hazards.

- In case of using an external cooling system position the hoses of the cooling system so that they will not be tripped over, pulled, or contact hot surfaces.

To prevent fire hazard

- Do not place flammable or combustible materials near the projector!

- Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an "exclusion zone" around all external surfaces of the projector whereby no flammable or combustible materials are present. The exclusion zone must be not less than 40 cm (16") for this projector.

- Do not place any object in the projection light path at close distance to the projection lens output. The concentrated light at the projection lens output may result in damage, fire or burn injuries.

- Ensure that the projector is solidly mounted so that the projection light path cannot be changed by accident.

Safety information

To prevent projector damage

• The air filters of the projector must be cleaned or replaced on a regular basis. Cleaning the booth area would be monthly-minimum. Neglecting this could result in disrupting the air flow inside the projector, causing overheating. Overheating may lead to the projector shutting down during operation.
• The projector must always be installed in a manner which ensures free flow of air into its air inlets.
• If more than one projector is installed in a common projection booth, the exhaust air flow requirements are valid for EACH individual projector system. Note that inadequate air extraction or cooling will result in decreased life expectancy of the projector as a whole as well as causing premature failure of the lasers.
• In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC) and safety requirements, it should always be operated with all of its covers in place.
• Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The device should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
• Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and remove all power from the projector. Do not operate the projector again until it has been checked by qualified service personnel.
• Do not block the projector cooling fans or free air movement around the projector.
• Do not use this equipment near water.
• Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices in which case there is a loss of warranty.
• Never place the projector in direct sunlight. Sunlight on the lens can severely damage the Digital Mirror Devices™ in which case there is a loss of warranty.
• Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For maximum protection, repack your set as it was originally packed at the factory.
• Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution.
• To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. For lens cleaning follow the instructions precisely as stipulated in the projector manual.
• Only use zoom lenses of the Barco TLD+ series on the 4K models of the projector. Using other lenses will damage the internal optics. For suitable fixed TLD+ lenses contact Barco or see Barco website.
• Allowed ambient temperature range depends on altitude

• If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.

Stacking and transporting

• Stack maximum 2 rental flight cases high. Never higher.
• Surface on which flight case is standing must be level to ensure that the total load is evenly spread out among the four wheels. The surface must also be able to support the load safely.
• Before stacking or transporting flight cases, check the wheels and their fixation screws for wear or defects.
• Before stacking or transporting flight cases, check that the four lock handles on each flight case are in good working order and locked securely.
• When stacked, make sure the wheels of the upper flight case are precisely positioned in the stacking dishes of the flight case below.
• Stacked flight cases may not be moved. Before stacking, the lower flight case must already be in its final resting position before placing the second upon it.
• Never stack loaded flight cases in a truck or other transport medium, unless each flight case is rigidly strapped tight.
• In the event of a wheel breaking, flight cases must be rigidly strapped tight to prevent a stack collapsing.
• Use an appropriate forklift to raise flight cases and take the necessary precautions to avoid personnel injury.

Safety Data Sheets for Hazardous Chemicals

For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available upon request via [e-mail].

1.3 Product safety labels

Light beam related safety labels

Safety information

Label image Label description

Label location

Hazard class 2: laser radiation warning symbol. 0.95 mW - 638 nm.

WARNING! DO NOT LOOK INTO THE BEAM NO DIRECT EYE EXPOSURE TO THE PROJECTOR BEAM IS PERMITTED LASER RADIATION - DO NOT STARE INTO LASER RANGING BEAM RG3 IEC EN 62471-5:2015 CLASS 2 IEC EN 60825-1:2014 HAZARD DISTANCE: CONSULT SAFETY MANUAL

THIS PRODUCT IS IN CONFORMITY WITH PERFORMANCE STANDARDS FOR LASER PRODUCTS UNDER 21 CFR 1040, EXCEPT WITH RESPECT TO THOSE CHARACTERISTICS AUTHORIZED BY VARIANCE NUMBER 2016-V-0144 EFFECTIVE ON DECEMBER 12, 2019. 警告！勿觀看投影機光束 眼睛勿直接接觸可允許暴露的光束 錯射幅射-勿直視 錯射範圍內光束 RG3 IEC EN 62471-5: 2015 CLASS 2 IEC EN 60825-1: 2014 危害距離：請參考安全手冊

1.4 High Brightness precautions: Hazard Distance

HD

Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the

Safety information

For example, projectors that have a HD greater than 1 m and emit light into an uncontrolled area where persons may be present should be positioned in accordance with "the fixed projector installation" parameters, resulting in a HD that does not extend into the audience area unless the beam is at least 2.0 meter above the floor level. In environments where unrestrained behavior is reasonably foreseeable, the minimum separation height should be greater than or equal to 3.0 meter to prevent potential exposure, for example by an individual sitting on another individual's shoulders, within the HD. Sufficiently large separation height may be achieved by mounting the image projector on the ceiling or through the use of physical barriers.

RA SIDE VIEW (A) TH HSH LRZ

TOP VIEW (B) RA RZ SW TH HD SW LRZ

Image 1-2
A Side view
B Top view
RA Restricted Access location (boot area of projector).
TH Theater
RZ Restriction Zone in the theater
HD Hazard Distance
LRZ Length Restriction Zone in the theater
H Height between surface floor and the light beam
SH Separation Height
SW Separation Width

Based on national requirements, no person is allowed to enter the projected beam within the zone between the projection lens and the related hazard distance (HD). This shall be physically impossible by creating sufficient separation height or by placing barriers. The minimum separation height takes into account the surface upon which persons other than operator, performers or employees are permitted to stand.

On Image 1-3 a typical setup is displayed. It must be verified if these minimum requirements are met. If required a restricted zone (RZ) in the theater must be established. This can be done by using physical barrier, like a red rope as illustrated in Image 1-3.

Safety information

not less than 1 meter. Alternatively, in case the height of the separation barrier for the horizontal clearance is at least 1 meter high then the horizontal clearance (SW) can be reduced to:

• 0 meter if the height of the hazard zone is minimum 2.5 meter.
• 0.1 meter if the height of the hazard zone is minimum 2.4 meter.
• 0.6 meter if the height of the hazard zone is minimum 2.2 meter.

LIPs for installations in unrestrained environment (concerts, ...) shall be installed at a height vertically above the floor such that the bottom plane of the Hazard distance Zone shall be no lower than 3 meters above the floor. Horizontal clearance to the hazard distance zone shall be not less than 2.5 meters. Any human access horizontally to the Hazard Zone, if applicable, shall be restricted by barriers. If human access is possible in an unsupervised environment, the horizontal or vertical clearances shall be increased to prevent exposure to the hazard distance zone.

The LIP shall be installed by Barco or by a trained and Barco-authorized installer or shall only be transferred to laser light show variance holders. This is applicable for dealers and distributors since they may need to install the LIP (demo install) and/or they transfer (sell, rent, lease) the LIP. Dealers and distributors shall preserve sales and installation records for a period of 5 years. Variance holders may currently hold a variance for production of Class IIIB and IV laser light shows and/or for incorporating RG3 LIPs. Laser light show variance for RG3 LIPs can be requested by mailing the application to [e-mail].

The installation checklist for laser illuminated RG3 projectors must be fully completed after the installation. The installation checklist can be downloaded from the Barco website. The installer shall preserve the checklist for a period of 5 years.

Install one or more readily accessible controls to immediately terminate LIP projection light. The power input at the projector side is considered as a reliable disconnect device. When required to switch off the projector, disconnect the power cord at the projector side. In case the power input at the projector side is not accessible (e.g. truss mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed wiring.

1.5 HD for fully enclosed projection systems

HD

Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the energy per surface unit becomes lower than the applicable exposure limit on the cornea or on the skin. The light beam is considered (to be) unsafe for exposure if the distance from a person to the light source is less than the HD.

RA Restricted Access location (enclosed projection area).

PR Projector

TH Theater (observation area).

RZ Restriction Zone

PD Projection Distance

SW Separation Width. Must be minimum 1 meter.

For this type of setup 3 different HD shall be considered:

• HD as discussed in "High Brightness precautions: Hazard Distance", page 16, relevant for intrabeam exposure.
• HD _reflection : the distance that has to be kept restrictive related to the reflected light from the rear projection screen.
• HD_ diffuse : the relevant distance to be considered while observing the diffuse surface of the rear projection screen.

As described in "High Brightness precautions: Hazard Distance", page 16, it is mandatory to create a restricted zone within the beam areas closer than any HD. In the enclosed projection area the combination of two restricted zones are relevant: The restricted zone of the projected beam toward the screen; taking into account 1 meter Separation Width (SW) from the beam onward. Combined with the restricted zone related to the rear reflection from the screen _D on; also taking into account a 1 meter lateral separation.

The HD _deflection distance equals 25% of the difference between the determined HD distance and the projection distance to the rear projection screen. To determine the HD distance for the used lens and projector model see chapter "HD in function of modifying optics", page 19.

The light emitted from the screen within the observation shall never exceed the RG2 exposure limit, determined at 10 cm. The HD _2 can be neglected if the measured light at the screen surface is below 5000 cd/m ^2 or 15000 LUX.

1.6 HD in function of modifying optics

Hazard distance

Safety information

HD Hazard Distance

TR Throw Ratio

1.7 Radio equipment (optional)

CE Conformity

This device may be equipped with WiFi & GSM modules for Pulse Input & Communication unit, which are fit for use in the European Union countries, EFTA and Turkey.

This device is restricted to indoor use only when operating in the 5150 to 5250 MHz frequency range.

Hereby, Barco declares that the radio equipment type UDM is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.barco.com/support

WiFi & GSM module

For WLAN:

For GSM:

• Frequency: 2402 MHz - 2482 Mhz
• Max EIRP: 19 dBm
• Frequency: 5150 - 5350 MHz / 5470 - 5725
• Max EIRP: 23 dBm
• E-GSM:
- Frequency: 900 MHz
Mhz- Max EIRP: 33.5 dBm
• EDGE:

• Frequency: 900 MHz
• Max EIRP: 28 dBm

• DCS:

- Frequency: 1800 MHz

- Max EIRP: 30.5 dBm

• EDGE:

- Frequency: 1800 MHz

- Max EIRP: 27 dBm

For UMTS:

• Band 1:
• Frequency: 2100 MHz
• Max EIRP: 24 dBm
• Band 8:
• Frequency: 900 MHz
• Max EIRP: 24 dBm

1.0 Compliance

Getting Started 2

2.1 Getting to know the projector 22
2.2 Power on the projector 24
2.3 Start image projection 25
2.4 Switching to ready mode....28 2.5 Power off projector....28

About this chapter

This chapter and by extension this whole document, the user manual, is intended for the user who want's to operate the projector. It does not contain installation instructions because the installation has to be done by trained and qualified service technicians. Refer to the projector installation manual for detailed installation instructions.

Getting Started

2.1 Getting to know the projector

Orientation convention

This manual refers to the left side of the projector as the side at your left hand when standing behind the projector and looking at the projection screen in front of the projector.

B T L R F Image 2-1 T Top L Left F Front R Right B Back

Projector component location

Simple line drawing of a rectangular frame with a small square and a numbered point (no text or symbols)

Getting Started

Technical line drawing of a rectangular electronic device with labeled ports (no text or symbols beyond numbers)

Image 2-3

9 IR receiver projector rear side
10 Mains power input socket (for C19 plug)
11 Power ON/OFF switch

12 Overvoltage status light
13 USB port (to control motorized rigging frame)

For detailed info about the Input & Communication module see chapter "Input & Communication", page 37.

Environment conditions
Table below summarizes the physical environment in which the projector safely operates or can be stored.

Environment	Operating Non-Operating
Ambient Temperature (depends on altitude)	0-1000 meter: 0°C (32°F) to 40°C (104°F)1000-3000 meter: 0°C (32°F) to 30°C (86°F)	-15°C (5°F) to 60°C (140°F)
Humidity 0% RH to 80%	RH Non-condensed 0% RH to 90% RH Non-Condensed
Altitude -60 m (-197 Ft)	to 3000 m (9843 Ft)1	-60 m (-197 Ft) to 10000 m (32810 Ft)

Getting Started

Diagram of a mechanical device with blue arrows indicating direction, no text or symbols present

Image 2-4

CAUTION: Keep the air inlets and outlet at all times free. Make sure there is a minimum distance of 40 cm (15.7 in) between the air outlet and the nearest solid object.

Projector Infra Red receivers and Remote Controle Unit

The projector has three Infra Red receivers: one at the rear (next to the power input), one at the front (below the lens holder) and one at the right side (integrated in the Input & Communication module).

Point the Remote Controle Unit (RCU) directly to the Infra Red (IR) receiver. Make sure you are within the effective operating distance (30 m, 100 ft in a straight line)

The RCU will not function properly if strong light strikes the IR sensor window or if there are obstacles between the RCU and the IR sensor.

Getting Started

Warning: Never switch on the projector if the OVERVOLTAGE status light lit up. Neglecting will cause irreversible damage to the projector.

▶ If no, proceed with the next step.

1. Press the mains switch (reference 2) to switch on this projector.

Diagram of a device panel with labeled components and directional arrows indicating assembly or movement

Image 2-6

- When '0' is pressed, the projector is switched off. - When 'I' is pressed, the projector is switched on.

The projector starts up to ready mode. The Power on/off button will blink until ready mode is achieved. Once in ready mode, the Power on/off button will be lit WHITE.

The start up screen is displayed on the touch panel.

Image 2-7

1. Press the Power on/off button on the projector, or the Power On button on the remote control. The projector will continue to power on mode. The Power on/off button will blink until the projector is ready. Once the projector is ready, the Power button will be lit BLUE.

Image 2-8

The background image of the startup person and info persons can be changed with Drinctor

Getting Started

Diagram showing cable installation process with connectors and power supply, illustrating cable connection and component assembly.

Image 2-9 Example of connecting an HDMI source.

1. Check if the SYNC LED lit up ORANGE (reference 1). This indicates that the sync is detected on the input signal.

Image 2-10

Select the source

1. Press the Input button (reference I) on the remote control or local keypad.

User interface toolbar with control buttons and a circular dial indicator showing check, edit, delete, and close options.

Getting Started

Menu Source UDX W40 L1 DisplayPort No signal HDCP L1 DisplayPort HDCP L1 HDBaseT 1 L1 HDBaseT 2 HDM2 L1 HDMI

Image 2-12 Example of the input selection menu

1. Use the arrow keys to select the desired source.

2. the SEL LED (reference 2) of the selected source lit up GREEN, and

3. the image of the selected source is projected.

Image 2-13

Quick test pattern selection

1. Press the Test pattern button (references P) on the remote control or local keypad.

Getting Started

2.4 Switching to ready mode

How to switch to ready mode

1. Press and hold the Power on/off button for 3 seconds on the local keypad, or press the Power Off button on the remote control.

The projector goes to Ready mode. The after-cooling cycle will start (about 30 seconds). During this period the Power on/off button will blink. Once the after-cooling cycle has ended, the projector will be in ready mode and the Power on/off button will be lit WHITE.

graph LR
    A["User Interface"] --> B["Time 3s"]
    B --> C["Time 30s"]
    C --> D["Time"]
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333
    style C fill:#cfc,stroke:#333
    style D fill:#fcc,stroke:#333

Image 2-15

While in ready mode, you can still navigate through the menus and set a limited amount of parameters.

Depending on the power savings settings of your device, if left untouched the projector will eventually go into standby or eco mode.

2.5 Power off projector

CAUTION: This procedure assumes the projector is in standby or ready mode.

How to power off

1. Switch off the projector with the mains switch. '0' must be pressed.

Pulse Remote Control Unit

3

3.1 Pulse RCU, battery installation 30
3.2 Pulse RCU, protocol setup 31
3.3 Pulse RCU, function of the on/off button 31
3.4 Using the RCU 32
3.5 Pulse RCU, Functionality overview 33
3.6 Pulse RCU, function of the "button pressed indicator" 33
3.7 Pulse RCU, function of the "RGB filter" button 34
3.8 Displaying and Programming addresses into the RCU 34
3.9 Using the XLR connector of the RCU 34
3.10 Using the mini-jack connector of the RCU 35
3.11 Pulse RCU, silicone protection sleeve (optional) 35

Pulse Remote Control Unit

3.1 Pulse RCU, battery installation

Where to find the batteries for the remote control ?

The batteries are not placed in the remote control unit to avoid control operation in its package, resulting in a shorter battery life time. At delivery the batteries can be found in a separated bag attached to the remote control unit. Before using your remote control, install the batteries first.

How to install

1. Push the battery cover tab with the fingernail a little backwards (1) and pull, at the same time, the cover upwards (2).

Diagram showing a remote control panel with labeled parts and directional arrows indicating assembly steps.

Image 3-1

1. Insert the two AA size batteries, making sure the polarities match the + and - marks inside the battery compartment.

Tip: Use alkaline batteries for optimum range and life time.

Pulse Remote Control Unit

CAUTION: Replace with the correct battery type. Use two AA size batteries. There is a risk of explosion if the battery is replaced with an incorrect type.

CAUTION: Replace the battery as explained above. There is a risk of explosion if the battery is incorrectly installed.

3.2 Pulse RCU, protocol setup

About the used protocol

The protocol is the code send out by the remote control when a button is pressed. Depending on this code, the projector can decode the signals. The remote control can be used with two different protocols: RC5 and NEC. Depending on the projector to control the remote control can be switched between these protocols.

Which protocol to use

• The NEC protocol has to be used for Barco projectors based on the Pulse platform: F70, F80, F90, HDX 4K, UDX, UDM, XDL, etc.
  • The RC5 protocol has to be used all legacy Barco projectors: HDQ 2k40, HDF, HDX W, etc.

How to set

1. Remove the cover. For more info on how to remove, see "Pulse RCU, battery installation", page 30.
2. Place the switch in the desired position.

Technical diagram showing a mechanical component with an inset close-up highlighting a red seal mark on the side panel.

Pulse Remote Control Unit

To activate the remote control, press the on/off button.

To deactivate the remote control, press the on/off button again.

Default after (re)placing batteries, is "ON".

Line drawing of a remote control device with a blue arrow pointing to the right button (no text or symbols present)

Image 3-5

3.4 Using the RCU

Pointing to the reflective screen or IR sensors

Switch on the RCU and point the front of the RCU to the reflective screen surface or point directly to one of the projector IR sensors. Make sure you are within the effective operating distance (30 m, 100 ft in a straight line). The RCU will not function properly if strong light strikes the IR sensor window or if there are obstacles between the RCU and the IR receiver.

Simple line diagram showing a vehicle approaching a plane with an arrow, no text or symbols present

3.5 Pulse RCU, Functionality overview

Remote Control Unit buttons

Diagram of a remote control with numbered labels pointing to various function keys and buttons

Image 3-7
1 Button pressed indicator
2 Shutter open
3 Shutter close
4 LCD panel on / off
5 Project OSD on / off
6 Lens zoom
Lens shift
8 Menu open / close
9 Menu selection. OK button
14 Backspace (while entering values)
15 XLR connector
16 Decimal mark (while entering values)
17 Macro button
18 Menu back
19 Default value button
20 Lens focus
21 RGB filter
22 Test patterns

Pulse Remote Control Unit

3.7 Pulse RCU, function of the "RGB filter" button

Filtering the color of the projected image

By pressing the RGB filter button on the RCU you can place a color filter on the output of the projector. This feature can be useful during the installation and configuration of a multi-projector or multi-channel setup. By having one projector project a red image and another project a green image, it is easier to spot and adjust the overlap section.

By pressing this button multiple times, you will have different active filters, in the following cycle:

• Red + Green + Blue (default)
- Red only
- Green only
- Blue only
- Red + Green
- Green + Blue
- Red + Blue
- Red + Green + Blue
• etc

After powering up, the colors will always revert back to full RGB.

3.8 Displaying and Programming addresses into the RCU

Displaying the Projector Address on the Screen.

1. If the projector is on, press the menu key and navigate to the Status page. The projector address and the broadcast address can be seen under the Communication heading.

The projector's address is displayed on the LCD status screen and / or the OSD.

How to Program an Address into the RCU?

How to use the XLR connector

1. Remove the XLR cover by pulling it backwards.

Diagram showing a device being processed from a left-side arrow to a right-side view of a BANOD device (no text or symbols present)

Image 3-8

1. Connect a cable with XLR plug into the XLR connector of the RCU.

2. Connect the other end of the cable with the XLR input of the projector.

Note: While the XLR cable is connected, the IR beam of the RCU is switched off.

3.10 Using the mini-jack connector of the RCU

Connecting a cable with the mini-jack connector will reset the broadcast address of the RCU to its default value '0'.

How to use the mini-jack connector

1. Connect a cable with the mini-jack connector (reference 2 Image 3-9) of the RCU.
2. Connect the other end of the cable with the mini-jack input of the projector.

Pulse Remote Control Unit

How to install

1. Pull off the rubber XLR-lid from the RCU.

Diagram showing a device transitioning from a remote to a control panel, with no text or symbols present.

Image 3-10

1. Place back side (XLR side) of the RCU into the sleeve and pull the other side of the sleeve over the front side of the RCU.

Two black plastic devices: a remote control case and a remote control device, shown with an arrow indicating transformation (no text or symbols present)

Image 3-11

Input & Communication

4

4.1 Introduction 38
4.2 Local Keypad and LCD panel 38
4.3 LCD touch panel 39
4.4 Communication connections....40
4.5 LED and Button indication chart....42
4.6 Pulse Quad Combo input Mk II 43 4.7 Pulse Quad Combo input Mk I 44
4.7 Pulse Quad Combo Input Mk 1 44 4.8 Pulse Quad RR 1.2 input 45
4.8 Pulse Quad DP 1.2 Input....45 4.9 Pulse SFP input....46

Input & Communication

4.1 Introduction

General

The Input & Communication module consists of a local keypad with LCD panel (1), a communication panel (4) and a Quad Combo input board (5). The free input slot can be used for optional modules (e.g. the Quad DP 1.2 input board).

Two boards of the same type can be used without restrictions. You can mount a second Quad Combo Input board in the free input slot (6). Alternatively, you can also remove the pre-mounted Quad Combo Input board and replace it with a second optional module (for example, a second Quad DP 1.2 input board).

Diagram of an electronic device rear panel with labeled ports and connectors

Image 4-1

1 Local Keypad and LCD panel

2 Optional antenna for WiFi connection

3 Optional antenna for GSM

4 Communication Panel

5 Quad Combo Input board

6 Free input slot (here filled with the Quad DP 1.2 Input board)

1 Menu navigation
2 Menu confirmation, OK button
3 Menu open / close
4 Menu back
5 Power on / off
6 Project OSD on / off

7 Input selection
8 Shutter open / close
9 Test patterns
10 Lens adjustment
11 LCD panel

Local Keypad

The Keypad gives direct access to several functions, in addition to access to the menu system.

The keypad has a backlight that can be switched on and off manually. By default the light turns off after 5 minutes.

The Power button and Shutter buttons are equipped with white, blue and red backlit LEDs. The other keys are only equipped with white and blue backlit LEDs. The LEDs are controlled according to the features available.

LCD panel

The LCD panel has two main functions:

1. Showing the menus, the adjustment information and also a mirror of the OSD, (On Screen Display) described in User Interface when this is enabled.

2. Information regarding the status of the projector showing this data:

3. Projector status
   • Network address
   • Active source

4. Current firmware version
   • Operation Data
   • Active functions (Enabled Functions).

Toggle between the two indications by using the Menu button on the keypad, or on the remote control.

The LCD Display will fade out 30 seconds after the last key operation.

4.3 LCD touch panel

The LCD menus can occasionally be slightly different in layout compared with the OSD menu, due to a more optimal layout regarding to the touch functionality of the LCD.

Input & Communication

4.4 Communication connections

Communication Panel

BAROD 12V 5A USB LAN IN DMX OUT REMOTE CITIC RS332 OUT FNB LIGHT WNT SEL ERR M ACT

Image 4-3
1 WIFI antenna for wireless IP (optional)
2 12V TA output 3 Firmware update / USB download log files
4 10/100 base-T for external control over IP and Art-Net
5 DMX interface input
6 DMX interface output 7 XLR input for wired projector control
8 RS232 for serial communication
9 Sync Out 3D
10 Sync In 3D
11 Status lights
12 IR receive sensor 13 GSM antenna inns
15 Сум антепна тра (брьона)

CAUTION: Ethernet should only be connected to either the 10/100 base-T port (on the communication panel) or the HDBaseT input (on the Quad Combo Input Mk II). Using both at the same time will lead to undefined behavior.

12 V output

12 V output, maximum 1 A, available when projector is not in stand by.

DMX interface

DMX is used as communication bus between different devices in the light technic. Each device has an input and an output, so that the bus can be looped between the different devices. According to the standard a five wire cable with XLR connector is used.

You can use the DMX input port to connect a DMX device (DMX console) to the projector. This way you can control the projector from that DMX device (console). The DMX output port can be connected with the next device in the loop.

Advantages of using RS232/RS422 serial communication:

- easy adjustment of the projector via PC (or MAC).

- allow storage of multiple projector configurations and set ups.

- wide range of control possibilities.

- address range from 0 to 255.

- sending data to the projector (update).

- copying data from the projector (backup).

RS232/422 input (Sub-D) port

Pin Description

1 DCD : Data Carrier Detect

2 RXD- : Receive Data

3 TXD- : Transmitted Data

4 DTR : Data Terminal Ready [RS232] / TXD+ : Transmitted Data [RS422]

5 GND : Ground

6 DSR : Data Set Ready [RS232] / RXD+ : Received Data [RS422]

7 — (not connected) —

8 CTS : Clear To Send

9 RI : Ring Indicator

RS232

An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the communication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for relatively short-range communications and does not specify balanced control lines. RS-232 is a serial control standard with a set number of conductors, data rate, word length and type of connector to be used. The standard specifies component connection standards with regard to computer interface. It is also called RS-232-C, which is the third version of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical '0' is > + 3V, Logical '1' is < - 3V. The range between -3V and +3V is the transition zone.

RS422

An F10 serial differential interface standard that specifies the electrical characteristics of balanced

Input & Communication

4.5 LED and Button indication chart

Button Backlight Status

Button Color status		Description
n	Blinking WHITE (slow) Projector starts up (booting)
	Blinking WHITE (fast) Firmware upgrade
	Solid WHITE Projector is in Standby or Ready mode
	Blinking BLUE Projector goes to ON mode
	Solid BLUE Projector is ON
	Blinking RED Error condition
Shutter button	Off (no color) Projector is OFF, starts up, or is in Standby or Ready mode.
	Solid WHITE Projector is ON, shutter is open
	Solid RED Projector is ON, shutter is closed

LED Status

PWR LIGHT ERR IR

LED

Color status

Description

PWR (power LED)

Off

Projector powers un

4.6 Pulse Quad Combo input Mk II

Overview Quad Combo Input Mk II

SD/IN SD/IN SD/IN/OUT SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/IN SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/INA SD/IN1 SD/IN2 SD/IN3 SD/IN4 SD/IN5 SD/IN6 SD/IN7 SD/IN8 SD/IN9 SD/IN10 SD/IN11 SD/IN12 SD/IN13 SD/IN14 SD/IN15 SD/IN16 SD/IN17 SD/IN18 SD/IN19 SD/IN20

Image 4-4

1 Quad SDI channel A: 3G/12G input

2 Quad SDI channel B: 3G input

3 Quad SDI channel C: 3G SDI input + 3G/12G output

4 Quad SDI channel D: 3G SDI input / output

5 DisplayPort Input

6 HDMI input

7 HDBaseT input 1

8 HDBaseT input 2

Functionality of the Quad Combo input Mk II

The Quad Combo Input Mk II support 12G input and throughput on the SDI connectors.

Compared with the Mk I the Mk II includes the following:

• SDI input A supports 12G input signals.
• SDI input C functions as a loop-through output for any signal placed on input A.
• SDI input D functions as a loop-through output for any signal placed on input B.
- HDBaseT input 1 supports network connectivity.

CAUTION: Ethernet should only be connected to either the 10/100 base-T port (on the communication panel) or the HDBaseT input (on the Quad Combo Input Mk II). Using both at the same time will lead to undefined behavior.

SDI input & output - How does it work?

When connecting an SDI source to the projector and the signal is HD or 3G, you can choose any of the four input connectors.

When connecting multiple projectors with the same signal, you can connect the signal as follows:

On the same signal to I and A, as if the final solution

Input & Communication

graph LR
    A["HO.95 & '20"] --> B["A"]
    B --> C["FPGA"]
    D["IN.4 & 30"] --> E["B"]
    E --> F["FPGA"]
    G["C"] --> H["STI INLOT"]
    I["D"] --> J["STI OUT"]
    K["IN.4 & 30 OUT, HO.95 & '20'"] --> L["STI OUT"]
    M["IN.4 & 30 OUT, HO.95 & '20'"] --> N["STI OUT"]
    O["IN.4 & 30 OUT, HO.95 & '20'"] --> P["STI OUT"]
    Q["IN.4 & 30 OUT, HO.95 & '20'"] --> R["STI OUT"]
    S["IN.4 & 30 OUT, HO.95 & '20'"] --> T["STI OUT"]
    U["IN.4 & 30 OUT, HO.95 & '20'"] --> V["STI OUT"]
    W["NC"] --> X["FPGA"]
    Y["NC"] --> Z["FPGA"]
    AA["NC"] --> AB["FPGA"]
    AC["NC"] --> AD["FPGA"]
    AE["NC"] --> AF["FPGA"]

Image 4-5

LED behavior

• The SYNC LED lit up ORANGE when valid input sync is detected.
  • The SEL LED lit up GREEN when the input is selected.
• The SEL LED blinks GREEN when the input/output is selected and configured as output.

For specifications about the supported inputs for SDI, HDMI, HDBaseT and DisplayPort 1.2 see chapter "Specifications", page 177.

4.7 Pulse Quad Combo input Mk I

Overview Quad Combo input Mk I

Input & Communication

Remark concerning the Mk I and Mk II inputs boards

The Mk I input board miss functionality that has been implemented on the Mk II input board. These missing features include:

• Loop-through functionality
  • 12G SDI support
  • Network connectivity on HDBaseT inputs

The projector is now standard equipped with the Mk II input board. For details and specifications see chapter "Pulse Quad Combo input Mk II", page 43.

Visual difference between the Mk I and Mk II input boards

There is one real visual aid to tell the two variants apart. There are visual markings added on the Mk II input board, marking which connector supports 12G and which only supports 3G.

Image 4-7 Quad Combo Input Mk I board, without markings above the SDI inputs

BANCO 30/120 30 30 30 30 30 30 SYNC BANCO A B C D

Image 4-8 Quad Combo Input Mk II board, with 3G/12G markings above the SDI inputs/outputs.

4.8 Pulse Quad DP 1.2 input

Quad DP 1.2 input

Input & Communication

4.9 Pulse SFP input

The Barco SFP Input Board has been designed and tested to work alongside the Barco SFP Output Board.

However, it is possible that the SFP Input board can also work with other third-party devices that support 12G over fiber. Due to the many third-party options available on the market, the input board could not be tested for every option available.

Overview SFP input

The SFP Input board is used to connect 12G SDI over fiber. The SFP input is delivered without any connector. It is up to the customer to buy the necessary connectors, transceivers and cables. These parts can be mounted on the indicated places on the front panel of the board.

BR/SD SIL SYNC Opt A SIL SYNC Opt B SFP A SFP B 1 2 3

Image 4-10
1 Neutrik Duo optical connector or Neutrik Quad optical connector
2 Neutrik Duo optical connector or Neutrik Quad optical connector
3 2x12G SDI/10GE transceiver

For specifications about the supported inputs for SFP see chapter "Specifications", page 177.

LED behavior

- The SYNC LED lit up ORANGE when valid input sync is detected.

• The SEL LED lit up GREEN when the input is selected.

Use cases

The SFP can be configured as follows:

GUI - Introduction

5

5.1 Overview 48
5.2 Navigation....51
5.3 Test Patterns 53

About this chapter

This chapter gives an general overview of the Graphic User Interface.

GUI - Introduction

5.1 Overview

Disclaimer on GUI images used in this manual

The GUI images in this manual are example illustrations and should be treated as such. While the name of the projector displayed in the illustrations may be different from the projector model you are currently using, the menu lay-out and functionality is identical.

GUI - First start of the software

When you start the projector for the first time, you will be requested to choose the system language. You can choose between the following languages:

• German (DE)
• English (EN-US)
• Spanish (ES)
• French (FR)
• Japanese (JA)
• Korean (KO)
• Portuguese (PT-BR)
  • Russian (RU)
• Chinese (ZH)

Select language F80-4K9 Welcome! Please select your language 汉语 Deutsch English (US) Español Français

GUI - Introduction

Settings Product registration UDX W40 1 2 3 4 Welcome to your Barco UDX W40 projector. To continue using your projector, it must be registered, Registration must be completed within 200 hours* of use. You have 20 hours remaining * You have 200 hours of illumination time before the registration must be complete X REGISTER LATER REGISTER NOW >

Image 5-2 Example of the Product registration form

GUI - Status Screens

While the projector menu is not active, or the projector is Ready or Standby mode, the Status screens remain visible. These screens give an overview of the state of the projector and can be navigated through using the left and right arrow keys, or by swiping the screen left or right. The status screens are the following:

• Dashboard: The main overview. This screen displays all the chosen options on the projector (chosen source, blending/masking, display mode, etc).
• About: General info about the projector. This includes serial number, software version, mounted lens and light source runtime. It also includes altitude, and the pitch and roll tilt angles.
• Notifications: The error and/or warning messages that are currently active. If no messages are active, this list will be empty.
• Preview: A preview pane of the projected image. If no image is being projected, a test image is displayed instead.

Preview NO SIGNAL

GUI - Introduction

The OSD can be disabled by pressing the OSD on/off button.

Menu L1 DisplayPort Source Image Installation Profiles Settings Test patterns Status UDX W40

Image 5-4 Example of the home menu

The projector software platform uses access levels what each user can do. A standard user has access to the standard projector functionality. A certified service technician has also access to the advanced settings menu. This menu is password protected. This password can only be obtained by following the service partner training.

GUI - Pulse software menu tree

graph TD
    A["Source"] --> B["Lx Quad combo"]
    B --> C["Connector x"]
    B --> D["Quad SDI"]
    B --> E["Connector settings"]
    A --> F["Lx Quad DP1"]
    F --> G["Connector x"]
    F --> H["Switched options"]
    F --> I["Connector settings"]
    A --> J["Lx SFP Input"]
    J --> K["Connector x"]
    J --> L["Connector settings"]
    A --> M["Image Profile"]
    M --> N["Context"]
    M --> O["Brightness"]
    M --> P["Saturation"]
    M --> Q["Sharpness"]
    M --> R["Gems"]
    M --> S["Digital zoom and shift"]
    M --> T["Advanced Settings"]
    T --> U["Realcolor P2"]
    T --> V["Output resolution"]
    T --> W["HDS"]
    T --> X["Dynamic Shift"]
    A --> Y["Installation"]
    Y --> Z["Laser range"]
    Y --> AA["Matsubishi frame"]
    Y --> AB["Center motor bed frame (action)"]
    Y --> AC["Orientation"]
    Y --> AD["Scaling"]
    Y --> AE["Illumination"]
    Y --> AF["3D"]
    Y --> AG["7 inch calibration"]
    A --> AH["Settings Test patterns Status"]
    AH --> AI["Product registration"]
    AH --> AJ["Data and time"]
    AH --> AK["Standby mode"]
    AH --> AL["Lens features"]
    AH --> AM["Profile x (actions)"]
    AH --> AN["Communication"]
    AN --> AO["Remote control"]
    AN --> AP["Host name"]
    AN --> AQ["LAN"]
    AN --> AR["HBase?"]
    AN --> AS["WRF"]
    AN --> AT["UNIX"]
    AN --> AU["SEM"]
    AN --> AV["Cloud services"]
    AN --> AW["Regulatory information?"]
    AH --> AX["User Interface"]
    AX --> AY["Language"]
    AX --> AZ["Themes"]
    AX --> BA["Units"]
    AX --> BB["System"]
    BB --> BC["Cooling mode"]
    BB --> BD["Operational mode"]
    BB --> BE["Capture mode quantity"]
    BB --> BF["Maintenance"]
    BF --> BG["Factory size"]
    BF --> BH["Lens calibration"]
    BF --> BI["Frame calibration"]
    BF --> BJ["Tit sensor"]
    AY --> BK["Winp"]
    BK --> BL["Winp (winoff)"]
    BK --> BM["Screen size"]
    BK --> BN["4 corners"]
    AY --> BO["Band and mark"]
    BO --> BP["Base Blend"]
    BO --> BQ["Band mask"]
    BO --> BR["Black level"]

GUI - Introduction

Diagram of a remote control panel with numbered labels pointing to function keys and buttons

User interface panel with numbered UI elements and control buttons

Image 5-6

To start up the menu structure, press MENU (1).

Use the arrow keys (Menu Navigation buttons) to navigate to the desired menu item (2). The background color changes to light blue.

Press the Menu Selection button (center key of the arrow keys), also called OK button, to activate that item and to jump one level deeper (3).

Use the numeral keys to enter values, or use the arrow keys to move the bar scale up or down. Press the Back button to go up one level (4).

Menu Menu UDX W40 LT DisplayPort Source Image Installation Profiles

To enter values with the local keyboard, use the arrow keys to select the first digit, press OK. Select the second digit and press OK. Continue until all digits are entered. Close the action by selecting the enter (←) button and press OK. Select the backspace button and press OK to remove the last entered digit.

Using the LCD touch display

From Pulse software 2.0 onward, the touch display functionality of the LCD panel has been activated and can be used.

Instead of using the remote control buttons or keypad keys or button, you can now:

• Touch menu icons to enter the respective menu.
• Swipe a menu up and down if not all information is not immediately visible (e.g. more than 8 (sub)menu icons being visible)
• Return to a higher menu level, by touching the blue name in the top left corner of the display.
• Use touch functionality to use menu items (check boxes, sliders, digital keyboard or keypads, etc).
• Swipe menu panes left or right when multiple panes are available (e.g. the Status menu)

Menu memory

The OSD menu remembers the last selected sub-item as long as the projector is running. The menu memory is reset when restarting the projector from standby.

5.3 Test Patterns

List of standard test patterns

The test patterns that are available by default are the following:

• Aspect
• Focus-Green
• Focus-bursts
• White / Black/ Red / Green / Blue
  • Cyan / Magenta / Yellow
• Color bars
• Color gradients
• Checkerboard
• Cross hatch

GUI - Introduction

Type Explanation		Example of test pattern icon
Standard test patterns	Standard test patterns. See previous list to see all test patterns available for your device.
Warped test patterns	Available from software 2.2 onward. Every test pattern will have "warped" variant available, symbolized with a "warp" symbol on the top-left corner of the icon.If active and configured, the warping will be applied to this test pattern. If warping is not active, or not configured, this will be identical to the standard test pattern.
Custom test patterns	If uploaded via an external tool, you will find your custom upload test patterns (and its warped variant) at the bottom of the list of available patterns.All custom uploaded test patterns will be marked with the default "test pattern file" icon.

How to use test patterns

1. In the main menu, select Test Patterns.

or

Push the Test Patterns button on the RC.

GUI – Source 6

6.1 Displaying a single source....56
6.2 Displaying multiple sources: Stitched layouts 56
6.3 Connector Settings 58

About the Source menu

This menu is used to select, review and configure sources into the projector.

GUI - Source

6.1 Displaying a single source

About selecting a source

Before a source can be projected, the source signal must be connected to the source input(s) of the device and a valid synchronization signal must be available along with the source signal on at least one of the input connectors.

How to select?

1. Press Menu to activate the menus and select Source.

Image 6-1 Main menu, Source

1. Press OK.

The Select Source menu is displayed with the actual available sources filled out.

Menu L1 DisplayPort Source UDX W40 No signal HDCP L1 DisplayPort HDCP L1 HDBaseT 1 HDCP2 L1 HDBaseT 2 L1 HDMI

The table below describes the different Stitch Layouts and scan directions.

Type of layout Description

1

Single

Available connectors Mode

A single source is displayed full screen

Quad Combo input:SDI (4x)HDBaseT (2x)DisplayPortHDMlQuad DP 1.2 Input:DisplayPort (4x)

Mono / Active stereo

1

2

Dual 1 x 2

Two inputs are required. TheQuad DP 1.2 Input: Mono / Active sources are displayed next to 2x DisplayPort each other.

1	2
3	4

Quad 2 x 2

Four inputs are required. The Quad Combo input: Mono / Active sources are displayed in four·4x SDI input stereo quadrants. Quad DP 1.2 Input: · 4x DisplayPort

1

2

3

4

Quad 1 x 4

Four inputs are required. The Quad DP 1.2 Input: Mono / Active sources are displayed next to 4x DisplayPort each other.

1

2 x single

Two inputs are required. TheQuad DP 1.2 Input: Passive stereo sources are displayed one · 2 x DisplayPort above the other.

1

2

2 x Dual 1 x TWO

Four inputs are required. TwoQuad DP 1.2 Input: Passive stereo sources are displayed next to 4x DisplayPort each other, while the other two are displayed above the first

Passive stereo

GUI - Source

Menu L1 HDMI No signal Source UDX 4K40 L1 SDI A L1 SDI B L1 SDI C L1 SDI D L2 FIBER A L2 FIBER B L1 Quad SDI Connector settings

Image 6-4 Example of the stitched layout options

1. Select the desired stitched input.

Tip: If the Quad DP input board is installed, scroll all the way down the menu for the stitched options on that board.

Menu Source HDX 4K20 L1 HDBaseT 1 No signal L2 DisplayPort A L2 DisplayPort B L2 DisplayPort C L2 DisplayPort D A B A C B D C D L2 Dual DP - AB L2 Dual DP - AC L2 Dual DP - BD L2 Dual DP - CD

Image 6-5 Example of the stitched input options with the Quad DP board installed

GUI - Source

Image 6-6 Main menu, Source

1. Press OK.

The Select Source menu is displayed with the actual available sources filled out.

1. Scroll down to the bottom of the list of available sources and select Connector Settings.

Image 6-7 Source menu, connector settings

The available input connectors are displayed.

Source Connector settings UDX W40 HDCP2 L1 HDMI HDCP L1 DisplayPort HDCP L1 HDBaseT 1 L1 HDBaseT 2

GUI - Source

1. You can change the following:

• To force a limit on the used signal range, select one of the available signal ranges.
- To force a limit on the color space, select one of the available color spaces.
• To set a video timing other than the one native for the connector, select one of the options under EDID.

Note: You cannot change the EDID for SDI connectors.

GUI - Image 7

7.1 Setting image levels manually....62
7.2 Adjusting the sharpness....63
7.3 Adjusting the gamma correction....64
7.4 Setting the desired Gamma type....65 7.5 Digital Shift & Zoom....67
7.6 RealColor P7 71
7.7 Displaying HDR content 73
7.8 Dynamic contrast....74

GUI - Image

7.1 Setting image levels manually

Purpose

Contrast: Change the contrast of the complete output signal of the projected image.

Brightness: Change the brightness of the complete output signal of the projected image.

Saturation: Change the saturation of the complete output signal of the projected image.

How to set up Contrast

1. In the main menu, select Image → Contrast.

Image 7-1 Image menu — Contrast

1. Use the ◀ or ▶ key to change the contrast enhancement until the desired value is reached (adjustable between 0 and 2).

< Image Image settings UDX W40 1.04 0.01 0.99 3

GUI - Image

< Image Image settings UDX W40 1.04 0.01 0.99 3

Image 7-4 Example of the image sliders, brightness is the second slider

1. If necessary, use the ▲ or ▼ key to select the other image adjustment options.

How to set up Saturation Level

1. In the main menu, select Image → Saturation.

Image 7-5 Image menu — Saturation

1. Use the ◀ or ▶ key to change the saturation until the desired value is reached (adjustable between 0 and 2).

Image Image settings UDX W40 1.04

GUI - Image

Increasing the sharpness will have the best effect in high contrast images, eg a table with text and borders. In a natural picture, high sharpness can be perceived as noise, as all details in the picture will be amplified. Available range: -2 to 8.

Default value: 0

graph LR
    A["-2 min"] --> B["-1"]
    B --> C["0"]
    C --> D["1"]
    D --> E["2"]
    E --> F["3"]
    F --> G["4"]
    G --> H["5"]
    H --> I["6"]
    I --> J["7"]
    J --> K["8 min"]
    style A fill:#fff,stroke:#000
    style K fill:#fff,stroke:#000
    subgraph Time_Steps
        L["Black"] --> M["Black"]
        N["Image"] --> O["Image"]
        P["Image"] --> Q["Image"]
    end

Image 7-7 Effect of sharpness adjust

How to adjust

1. In the main menu, select Image → Sharpness.

Image 7-8 Image menu - Sharpness

1. Use the ◀ or ▶ key to change the sharpness until the desired value is reached.

Image Image settings UDX W40 1.04 0.01

GUI - Image

Image 7-10 Image menu - Gamma

1. Use the ▼ key to select the slider.

2. Use the ◀ or ▶ key to change the gamma value between 1.0 and 2.8. The default value is 2.2.

Tip: The slider can be adjusted with a precision of 0.1.

Image Gamma UDM 4K22 Type: auto power srgb dicom_10 dicom_60 dicom > 1.4 Detected gamma LT HDMI POWER

Image 7-11 Example of the gamma menu

7.4 Setting the desired Gamma type

About the alternate gamma types

Next to the standard gamma correction. the projectors can be manipulated in a way to simulate gamma types.

GUI - Image

If the source signal is HDR encoded an HDR icon will be visible next to the source signal. This is visible both the Source selection menu, as well as the status menu.

Menu Status UDX 4K32 L1 HDMI L1 HDMI 1086p 50 Hz Display mode Mono Transport delay 292 Frequency 60.3 Hz Output resolution 46.2Hz - Fill aspect Filter mode ON 40% Flex 24% 23% 101 Mb 21% UDX-4K32 590077435 10.200.32.80 0 0 1

Image 7-12 Example of the HDR icon on the status menu

For more info on PQ and HDR, refer to "Displaying HDR content", page 73.

How to adjust the gamma type?

1. In the main menu, select Image → Gamma type.

Image 7-13 Image menu - Gamma

The Gamma type menu is displayed. If source content is available, the detected gamma of the source will be displayed at the bottom of the menu.

GUI - Image

Image Gamma UDM 4K22 Type: auto power srgb dicom_10 dicom_60 dicom 2.2 Detected gamma L1 DisplayPort POWER

Image 7-15 Example of selecting a gamma type

Tip: If not sure what gamma type to select, keep the default value auto selected. This automatic mode will determine the used gamma type based on the incoming signal.

However: keep in mind when using the automatic mode, your media player needs to be configured correctly as well. While most mainstream media player devices will be configured correctly by default, we cannot guarantee this is the case for every device available on the market. If you notice the projected image seems "off", it may be necessary to check the configuration of your media player. For more info, check the user guide of your media player device.

7.5 Digital Shift & Zoom

What can be done?

The image can be optically shifted by using the vertical and horizontal lens shift.

If you want to reach a lens shift beyond what is possible with the optical shift, you can also perform a digital lens shift. This digital shift will occur on the DMD, rather than the lens holder. So take into account that this additional shift is minimal and restricted to the limits of the chip used.

For the optical zoom and lens shift, navigate to Home → Installation → Lens.

GUI - Image

Close-up of a koala with textured skin and visible eye, surrounded by foliage (no text or symbols)

Image 7-16 Originally picture, not digitally zoomed

Close-up of a koala's face showing its eyes and mouth (no text or symbols visible)

Close-up photo of a koala holding an object, no visible text or symbols

Image 7-17 Picture digitally zoomed in Image 7-18 Picture digitally zoomed out

The effect of Digital Shift

GUI - Image

Close-up of a koala with textured skin and visible eye, surrounded by foliage (no text or symbols)

Image 7-19 Original Picture, not digitally shifted

Close-up photo of a koala resting on its back, showing its expressive face and mouth (no text or symbols visible)

Close-up photo of a koala with visible eye and mouth, no text or symbols present

Image 7-20 Picture shifted horizontally Image 7-21 Picture shifted vertically
Digital Shift & Zoom

GUI - Image

Digital zoom and shift UDM 4K22 < Image Shift Zoom Reset SHIFT ZOOM Shift -4 T -3 Zoom -3840 % 2400 % 100.00

Image 7-23 Example of the digital zoom and shift menu

1. In order to optimize the digital zoom, enable the Zoom slider. In order to optimize the digital shift, enable the Shift slider.
2. When one or both of the modes are enabled, use the arrow keys to select the mini-keypad in this menu. Use the enter key to activate this mini-keypad.

If digital shift is enabled, the keypad will transform into the keypad for digital shift. If only digital zoom is active, it will automatically transform in they keypad for digital zoom.

Digital zoom and shift UDM 4K22 Shift Zoom Reset SHIFT ZOOM Shift 4 % -3 Zoom 3840 % 2400 % 100.00

GUI - Image

• Use the ▲ or ▼ key to shift the lens (image) in vertical direction.
• Use the enter key to transform the keypad to digital zoom mode (if enabled).

• Use the return key to exit without saving.

• If digital zoom is enabled, you can now do the following:

• Use the ◀ or ▶ key to zoom the lens in or out.

• Use the enter key to either finish digital shift and zoom.
• Use the return key to exit without saving.

7.6 RealColor P7

Purpose

When blending images from multiple projectors, the measured color coordination of each projector can be altered to a desired common level. This so that the projected colors are identical over all projectors used. Alternatively, if you are unfamiliar with how to adjust the colors to a specific setting, there are also a certain number of presets available, which forces the color output to specific color standards.

How to set custom P7 values

1. In the main menu, select Image → Advanced → RealColor P7.

Image 7-26 Advanced settings menu - RealColor P7

The P7 menu is displayed.

Advanced setti... RealColor P7 Custom CustomRGBCMY Custom CustomWHITE UDX W40

GUI - Image

• Temperature: Configure the white point via a color temperature slider.

The white point is specified on a Kelvin scale between 3200K and 13000K tracking along the black body curve.

1. Define the coordinates for each available color.

Click on a coordinate value and select the current value. Enter the desired value with the numeric keys.

Note: You can only pick coordinates within the measured color triangle.

You can reset all coordinates to the default values (to native) by clicking the Reset icon.

How to choose one of the P7 presets

1. In the main menu, select Image → Advanced → Realcolor P7.

Image 7-28 Advanced settings menu - RealColor P7

The P7 menu is displayed.

Advanced settl... RealColor P7 Custom Custom/GECMY: Custom Custom/WEET: Prefnt Feature WhitePaint Coefficient + White 0.313 0.229 Gain Luminance 1.0 Red 0.671 0.505 1 1 Green 1.348 0.673 0.703 Blue 1.44 0.547 0.554 UDX W40

GUI - Image

Advanced settl... RealColor P7 UDX 4K40 Preview Value Present EBL Whitepoint Laser x y Gain Luminance White 0.357 0.370 1.000 1.000 Red 0.641 0.332 1.000 0.229 Green 0.265 0.640 1.000 0.682 Blue 0.249 0.166 1.000 0.679 Cyan 0.200 0.332 1.000 0.771 Magenta 0.326 0.151 1.000 0.308 Yellow 0.428 0.526 1.000 0.921

Image 7-30 Example of one of the presets, here DCI-P3

Note: After choosing one of the presets, you can still alter the values of the coordinates to your own choosing, similarly to how you set custom P7 values.

Use the Reset icon to return to the default values of the chosen preset.

7.7 Displaying HDR content

About HDR and PQ

Perceptual Quantizer (PQ) is a non-linear electro-optical transfer function (EOTF) that allows for the display of High Dynamic Range (HDR) content with a luminance level of up to 10 000 cd/m² and can be used with the Rec. 2020 color space.

When do I know my content is HDR encoded?

If the source signal is HDR encoded, an HDR icon will be visible next to the source signal. This is visible both in the Source selection menu, as well as the status menu.

GUI - Image

The projected HDR content depends on the following factors:

• Mastering luminance: This is content-specific and cannot be changed.
  • Screen luminance: Every projection screen has a specific luminance (measured in nits or foot-Lambert).
  Entering this luminance in the projector will adapt the content towards the intended HDR result.
• HDR Boost: A variable "booster" that may amplify or downplay the HDR output.

How to set the HDR-related parameters?

1. Make sure the chosen Gamma Type is set to AUTO. For more info, refer to "Setting the desired Gamma type", page 65.
2. In the main menu, select Image → Advanced → HDR.

Image 7-32 Advanced settings menu, HDR

The HDR menu is displayed.

Advanced settings HDR UDX W40 Screen luminance unit ✓ nits □ foot-Lambert Screen luminance < 524 > HDR boost < 1 >

GUI - Image

How to set the dynamic contrast?

1. In the main menu, select Image → Advanced → DynaBlack.

Image 7-34

The DynaBlack menu is displayed.

Advanced settin... DynaBlack UDM 4K22 Off Low Medium High Max

Image 7-35 Example of the DynaBlack menu

1. Select the desired dynamic contrast setting, or leave the default on (medium).

The result will slowly become visible.

Do not panic if there isn't a visible change after a few seconds. Each change in the dynamic contrast menu has an impact on the light source, thus these changes will only become visible over time.

GUI - Image

GUI - Installation

8

8.1 Configuring the lens, optical zoom-focus 78
8.2 Configuring the lens, shift 78
8.3 Configuring the lens, dynamic focus 79
8.4 Configuring the lens, Shift to center....80
8.5 Configuring the lens, tilt sensor....81
8.6 Laser ranging 82
8.7 Manipulating the rigging frame 83
8.8 Manipulating the rigging frame, center position 85
8.9 Orientation 85
8.10 Scaling modes 86
8.11 Warping....87
8.12 Blending & masking 100
8.13 Illumination 110
8.14 3D projection....111

GUI - Installation

8.1 Configuring the lens, optical zoom-focus

What can be done?

If a motorized lens has been mounted onto the projector, you can fine-tune the projected image.

Zoom - Focus

1. In the main menu, select Installation → Lens → Zoom focus.

Image 8-1 Lens menu, Zoom & Focus

The Zoom and focus menu is displayed.

Lens Zoom focus UDX 4K32 Focus Zoom 29283 7185 Use test pattern key to toggle test pattern display

Image 8-2 Example of the zoom and focus adjustment menu

1. Use the ▲ or ▼ key to zoom the lens in or out.

GUI - Installation

Image 8-3 Lens menu, lens shift

The Lens shift menu is displayed.

Lens shift UDX 4K32 Horizontal Vertical 11695 1268 Use test pattern key to toggle test pattern display

Image 8-4 Example of the lens shift menu

1. Use the ◀ and ▶ keys to shift the lens (image) in horizontal direction.
   Use the ▲ and ▼ keys to shift the lens (image) in vertical direction.

8.3 Configuring the lens, dynamic focus

About focus drift and dynamic focus

Due to the design of TLD+ lenses and ultra-short throw lenses (UST lenses), these type of lenses tends to heat up over time when used in projectors. This has the side-effect of a slight shift in focus between the lens i

GUI - Installation

Installation Lens UDX W40 Zoom focus Shift Dynamic focus Shift to center

Image 8-5 Example of the Lens menu

1. In the Lens menu, click Dynamic focus to toggle between On and Off.

Image 8-6 Lens menu, Dynamic focus enabled Image 8-7 Lens menu, Dynamic focus disabled

Note: The Dynamic focus slider is only visible when the light source is on.

8.4 Configuring the lens, Shift to center

What can be done?

The lens can be forced back to the center position by selecting Shift to center.

GUI - Installation

Installation Lens UDX W40 Zoom Confirm action Are you sure you want to shift the lens to the center? ✓ CONFIRM × CANCEL

Image 8-9 Example of the Shift to center action

The lens will calibrate itself and return to the center position.

8.5 Configuring the lens, tilt sensor

When to use the tilt sensor menu

The projector has a built-in tilt sensor that detects the angle at which the projector is mounted. If you are in a situation where you need to fine-tune the projector because you want to achieve a picture at a specific angle (e.g. perfectly level, or a perfect fit in a multi-projector setup), you can use the tilt sensor menu as an aide when adjusting the projector feet, rigging frame or other used mounting mechanisms.

How to read the tilt sensor values

1. In the main menu, select Installation → Lens → Tilt sensor.

GUI - Installation

If you notice the tilt sensor isn't working correctly (e.g. when compared to a level), you can calibrate the sensor in the settings menu. For more info, see "Advanced settings – Tilt sensor calibration", page 163.

8.6 Laser ranging

What can be done?

When the optional laser range finder is installed on the projector, you can use the laser source to measure the distance between the front of the projector and the surface you are projecting on.

This can help you fine-tune the position of the projector.

Take into account that while a laser ranging session is active, the projected image will be off. This to have no interference between laser pointer and projected image. Instead, a red border will be projected giving the outline of where the projected image should be.

How to manipulate the laser range finder?

1. In the main menu, select Installation → Laser ranging.

Image 8–12 Installation menu, laser ranging

The Laser ranging menu is displayed.

Installation Laser ranging UDX W40 Note: For the best and most precise measurements, the screen content will be blanked while the measurements are being taken. To show the measurement result on screen, enable the switch below. The result is also shown on the laser ranging device and LCD screen.

GUI - Installation

2.243 K→X

Image 8-14 Example of projected image during laser ranging session with measurement on screen

By default the measurement is in meters. If you want the distance projected in feet, you can change the measurement system in the System settings menu. For more info, refer to "Units (measurement) system setup", page 138.

8.7 Manipulating the rigging frame

When can you manipulate the rigging frame?

You can manipulate the rigging frame in the Pulse menu when:

• The projector is mounted in a motorized rigging frame.
- The wiring of the motorization is connected to the projector, including the XLR connector.
- The XLR connector is enabled and powered to 24V. For more info on how to power the XLR connector, see "Front XLR output voltage control", page 135.

How to manipulate the rigging frame?

1. In the main menu, select Installation → Lens → Motorized frame.

GUI - Installation

Lens Motorized frame F80-4K9 Press ✓ to enter motor control. ✓ ✓ ✓ Invert horizontal Invert vertical Invert rotation

Image 8-16 Example of the Motorized frame menu

1. Press the OK key or button to activate the frame shift motors.

Lens Motorized frame F80-4K9 Press: ✓ to toggle rotation motors Press: ✓ to exit motor control ✓ ✓ ✓ Invert horizontal Invert vertical Invert rotation

Image 8-17 Example of horizontal and vertical frame shift

1. Use the ▲ or ▼ button to shift the rigging frame (image) in vertical direction.

Use the ◀ or ▶ button to shift the rigging frame (image) in horizontal direction.

GUI - Installation

8.8 Manipulating the rigging frame, center position

What can be done?

The motorized frame can be forced back to the center position by selecting Center motorized frame.

How to reset the motorized frame?

1. In the main menu, select Installation → Lens → Center motorized frame.

Image 8-19 Lens menu, Center motorized frame

A confirm action prompt will be displayed.

Installation Lens F80-4K9 Confirm action Are you sure you want to shift the Motorized frame to the center? ✓ CONFIRM ✗ CANCEL

GUI - Installation

How to set the correct orientation

1. In the main menu, select Installation → Orientation.

Image 8-21 Installation menu, orientation

The Orientation menu is displayed.

Installation Orientation UDM 4K22 Desktop front Desktop rear Ceiling front Ceiling rear Desktop front Auto front Auto rear

Image 8-22 Example of the orientation menu

1. Use the ◀ or ▶ keys to select the projector orientation mode and press OK to activate.

8.10 Scaling modes

About scaling modes

GUI - Installation

Scaling Mode	Explanation Example image	3
Fill screen Fills	the screen to the screen size defined in the Screen Size menu, while respecting the original aspect ratio. For more info on adjusting the Screen Size menu, so "Warping - Screen Size", page 88.
Stretch This mode stretches the image to the screen size defined in the Screen Size menu, while ignoring the original aspect ratio. For more info on adjusting the Screen Size menu, see "Warping - Screen Size", page 88.

Setting a scaling mode

1. In the main menu, select Installation → Scaling.

Image 8-23 Installation menu, scaling

The scaling mode menu is displayed.

Installation Scaling mode UDX W40

GUI - Installation

8.11.1 Warping - On/Off

About warping on/off

By toggling between on and off the warping functionality can be enabled or disabled.

How to toggle

1. In the main menu, select Installation → Warp.

Image 8-25 Installation menu, warp

The Warp menu is displayed.

Installation Warp UDX W40 Warp Screen size 4 corners Bow Warp files Transport delay

Image 8-26 Example of the Warp menu

1. In the Warp menu, click Warp to toggle between On and Off.

GUI - Installation

Two cows standing on a rocky stream with water flowing, surrounded by green grass (no text or symbols visible)

Image 8-29 Warp outline example

Using the screen aspect ratio presets

1. In the main menu, select Installation → Warp → Screen Size.

Image 8-30 Warp menu, screen size

The Screen Size menu is displayed.

Warp Screen size FS400-HR Screen aspect ratio presets 1:1 3:2 5:4 4:3 16:9 16:10

GUI - Installation

Screen size FS400-HR Screen aspect ratio presets 1:1 3:2 5:4 4:3 16:9 16:10 1.37:1 1.85:1 2.2:1 2.35:1 2.37:1 2.39:1 Screen width 3 Screen height 2 ✓ APPLY

Image 8-32 Example of the screen size menu, with preset "3:2" selected.

The selected ratio is filled out next to Screen width and Screen height.

3. Click Apply.

How to adjust the image with pixels?

1. In the main menu, select Installation → Warp → Screen Size.

Image 8-33 Warp menu. screen size

The Screen Size menu is displayed.

GUI - Installation

< Warp Screen size FS400-HR 1.07.1 1.09.1 2.2.1 2.50.1 3.07.1 3.29.1 Screen width 4096 Screen height 2176 7 8 9 4 5 6 1 2 3 , 0 .

Image 8-35 Example of the Screen size menu, editing the screen width

Tip: A red border will be projected along with the current image. The border is a visual tool, showing the result of the adjusted outline.

Warp Screen size UDX W40 Screen Width: 1920 Screen Height: 1080 ✓ APPLY

GUI - Installation

Exterior view of a large cargo aircraft with visible tail number 170 and landing gear deployed (no signage or text)

Airplane in flight with landing gear deployed, no visible text or symbols

Image 8-37 4 corner adjustment

How to adjust the image?

1. In the main menu, select Installation → Warp → 4 Corners.

Image 8-38 Warp menu, 4 corners

The 4 corners menu is displayed.

Warp 4 corners UDX W40 Warp 4 corner Helper lines RESET Top left X: 213 Y: 140 Bottom left X: 100 Y: 100

GUI - Installation

Warp 4 corners HDX 4K20 Warp 4 corner Helper lines Top left X: 6 Y: 8 Bottom left X: 8 Y: 8 Top right X: 8 Y: 8 Bottom right X: 8 Y: 8

Image 8-40 Example of 4 comers warping menu, with helper lines active on the edges of the screen

1. To set warping on one of the four corners, select one of the four corners and confirm.
2. Set the desired X and Y coordinates for this corner, using the arrow keys, and confirm.

After confirming, the helper lines for that comer will jump to the entered XY coordinate (if helper lines were enabled).

Warp 4 corners UDX 4K40 Warp 4 corner Helper lines RESET Top left X: 512 Y: 370 Bottom left X: 0 Y: -5 Top right X: 0 Y: 4

GUI - Installation

Image 8-42 Bow distortion

Definition of angle and linearity (length) in the bow warp procedure

Angle Length (Liposity)

GUI - Installation

Warp Bow UDM 4K22 Warp Bow Symmetric Angle 0.00° Length 1.0000

Image 8-45 Both the Bow and Symmetric sliders are set to on

1. Use the arrow keys to select the helping lines that represent the picture and confirm.

The helping lines that represent the projected picture are now colored blue, while the others are colored white.

Warp Bow UDM 4K22 Warp Bow Symmetric Angle 0.04° Length 1.0000

Image 8-46 The upper line is colored blue, the other sides are colored white

GUI - Installation

The correction will occur symmetrically on each side of the center of the highlighted side. 7. Repeat this step for all sides of the picture that has to be corrected, until the desired transformation has been achieved.

Pure grid pattern with curved boundaries and dots, no text or symbols present

Image 8-48 Example of a symmetric bow correction

Asymmetric bow correction

1. In the Bow menu, enable the Bow slider and disable the symmetric slider.

Warp Bow UDM 4K22 Warp Bow Symmetric Angle → 0.00° Length 1.0000

GUI - Installation

1. Select the desired slider and confirm.

Warp Bow UDM 4K22 Warp Bow Symmetric Apple 0.00" Length 1.0000

Image 8-51

1. Adjust angle and linearity (length) individually to obtain the correct correction. Press enter to confirm and to switch between angle and length.

Tip: Adjust the angle by using the up and down arrow keys. Adjust the linearity by using the left and right arrow keys.

1. Repeat the previous steps for each side of the picture that must be corrected.

2. When completed, a transformation will occur in a way similar to the following example. Observe that the upper side of the picture now has an asymmetric correction.

Abstract geometric diagram with grid lines and red dots, no text or symbols present

GUI - Installation

For more information on uploading/downloading Warp files using curl or other tools that supports HTTP upload, refer to the Pulse API Reference Guide.

When uploading a warp file that is too big, or with warp parameters outside the limits of the projector, some irregularities can occur. It will show up in two ways:

1: No warp enabled, picture still unwarped.

2: Distortions and artifacts in the edges of the picture.

There will be no error messages or warnings in the display when this occurs. The above mentioned symptoms is the only indication of this case.

How to activate an uploaded Warp grid?

1. In the main menu, select Installation → Warp.

Image 8-53 Installation menu, Warp

1. In the Warp menu, select Warp files.

Image 8–54 Warp menu, Warp files

The Warp Files menu is displayed.

GUI - Installation

Warp Warp files UDX 4K32 Enable (preview2590077436.xml

Image 8-56 Example of the Warp files menu

8.11.6 Warping - Latency control in a multi projector setup

Transport latency

The added delay in the image processing chain. The value is the number of lines relative to the output resolution.

Latency

The total time from the first pixel is coming in on an input source, until the first light representing that pixel is visible on the screen. This includes the transport delay. The value is normally given in milliseconds.

Functional description

Every projector in a multi-projector setup will have a different latency. This latency depends on the amount of warp and on the frequency of the projected image. In order to have no visible difference in the overall projected image, the user needs to be able to control the latency of each projector.

The latency value can be read out in the status menu for each individual projector.

How to configure transport delay?

GUI - Installation

Image 8-58 Installation menu, Warp

1. In the Warp menu, select Transport Delay.

Image 8-59 Warp menu. Transport delay

The Transport menu is displayed.

Warp Transport delay UDX W40 Minum Delay: 0 Actual Delay: 0 Desired Delay: 0 ✓ APPLY

Image 8-60 Example of the Transport delay menu

GUI - Installation

Width, Projector 2Width, Projector 1 Picture frame Projector 1 Picture frame Projector 2 Overlap / Blend Zone

Image 8-61

From the start (mask) position, you can blend zone size per edge (left, top, right, bottom). For each edge there will be a drop-off curve for the blend zone.

Waiting period and blend maintenance period

The heating and cooling down of the lens in a projector startup and shutdown cycle can have a minor drifting effect on the blending and masking areas. Due to this, it is advised to wait 15–20 minutes after projector startup before performing blending and masking actions. This to make sure the drift on the blend region is as minimal as possible. For a similar reason, it is advised to wait 15–20 minutes after projector startup before starting any blending maintenance in your existing setup.

It is recommended to perform a blend maintenance after every 10–20 startup-shutdown cycles of the projector.

8.12.1 Basic blend

How to set up a basic blend zone?

1. In the main menu, select Installation → Blend and Mask → Basic blend.

GUI - Installation

Blend Basic blend UDX W40 Enable Show lines RESET Top 0 Left 0 Gamma 2 Right 0 Bottom 0

Image 8-63 Example of the basic blend menu

1. To enable blending, put the Enable switch to the right. The color of the switch becomes blue when enabled.
2. To project masking lines on the screen, put the Show lines switch to the right. The color of the switch becomes blue when enabled.
3. Determine the start position of the blend area height and width to determine the dimension of the blend zone.

When the helping lines are activated, you will get a visual indication of the screen of the installed blending area.

Side view of a white airplane with 'JN' markings against a blue sky background (no text or symbols on the aircraft body)

Do not forget to disable the Show lines button after you achieved the desired blend zone.

8.12.2 Blend & Blend mask

About masking and blending width or height

Offset is used to clip the image on one or multiple sides (masking). This is used to hide parts of the picture that should not be shown on the screen. For example: if the source is a Windows PC, you can hide the menu bar using this method.

The larger the Mask value, the more the image is masked (by black bar) at the corresponding side. E.g. Top mask of 100 will blank the top 100 lines.

Height or width is used to create a blending zone with a smooth brightness drop off. This is used to compensate for the double brightness in overlap areas. The value is the size of the blended area in pixels.

How to set up basic blend zones?

1. In the main menu, select Installation → Blend and Mask → Blend mask.

Image 8-65 Blend menu, Blend mask

The Blend mask menu is displayed.

Blend Blend mask UDX W40 Enable Show lines RESET Top 0

GUI - Installation

JAL ① ②

Image 8-67

1 Start position (mask)

2 Blending width

1. Select one of the four starting positions values with the arrow keys and confirm.
2. Use the arrow keys or remote digits to change the value of the mask and confirm.
3. Repeat this process for all other desired sides.

Do not forget to disable the Show lines button after you achieved the desired blend zone.

Example of the use of blending

GUI - Installation

right Projector 1 Overlap area Width Width Width

Image 8-68 Set up for projector 1

Left Projection 2 Overlap area Wash Wash Wash

Image 8-69 Set up for projector 2

GUI - Installation

Image 8-70 Blend and mask menu, Blend files

The Blend Files menu is displayed.

Blend Enable gg.babl Blend files UDX 4K40 1/8 files selected

Image 8-71 Example of the blend files menu

1. If any custom Blend files are available, select the desired file.

Blend Blend files UDX 4K40 Enable 1/8 files selected gg.babl

GUI - Installation

You can also specify the offsets manually by turning off the automatic calculation. The black level value is adjusted in a 16-bit resolution from 0 to 65535.

The following figure shows how this occurs in a side by side configuration without any correction of the black level.

Picture Left Picture RightBlend Zone

Pure black image with a vertical gray stripe on the left edge (no text or symbols)

Image 8–73

How to adjust the black level manually

1. In the main menu, select Installation → Blend and Mask → Black Level.

Image 8-74 Blend and Mask menu, Black level

The Basic black level menu is displayed.

GUI - Installation

This value can also be entered by the numeric keys on the remote control.
6. Repeat the same procedure for any other projector connected to this projector, but on the opposite side.

Note: Do not forget to disable the Show lines button after you achieved the desired blend zone.

8.12.5 RGB gain adjustment

About RGB gain adjustment

The purpose of black level correction is to ensure a uniform black level in multi projector setups. Even when two projectors are of the same type, different projectors will output slightly different colors for black due to minor variations in their optical components. So if the projected image of the projectors overlap, there will be 3 different black levels: one for the zone where only the picture of the left projector (zone 1), one for the Blend zone (zone 2), and one for the zone where there is only the picture of the right projector (zone 3).

Picture Left Picture RightBlend Zone

Pure black image with a vertical gray stripe on the left edge (no text or symbols)

Image 8–76

The black levels for zone 1 and zone 3 are typically corrected by defining a black level mask, which is applied to the image of each projector. This system is already in place but the applied mask is monochrome. Using the Basic Black Level menu, you can already specify the area of the mask and its contents. But by using the RGB Adjustment page, you can specify the multiplication factors (gains) for the Red, Green and Blue colors separately.

GUI - Installation

Image 8-78 Example of the default black level menu

1. Select one of the three sliders on the bottom of the menu (Red, Green or Blue).
2. Use the left and right arrow keys to modify the gain of the chosen color.
3. Repeat for every slider until the desired result is achieved on screen.

8.12.6 Black Level Files

About custom Black Level Files

Next to setting your specific Black Level Adjustment in the GUI, you can also upload or download a custom Black Level adjustment file in png, jpeg or tiff format to/from the projector.

To upload or download Black Level adjustment files you can use Projector Toolset or upload/download the Black Level adjustment file in the format of an XML file. Alternatively, you can contact the "file endpoint" directly via the curl program or some other tool that supports http upload.

For more information on uploading/downloading Black Level files using the Projector Toolset, refer to the Projector Toolset user manual. For more information on uploading/downloading Black Level files using curl or other tools that supports HTTP upload, refer to the Pulse API Reference Guide.

When uploading custom black level files onto multiple projectors, make sure that the resolution of the file is supported by the projector you are uploading it to. A mismatch of projector resolution and black level file resolution will result in a sub-refined issue preferences. Verify the supported

GUI - Installation

Blend Black level files UDX W40 Enable No files available

Image 8-80 Example of the black level files menu

1. If any custom Black Level adjustment files are available, select the desired file.

Blend Black level files UDX 4K32 Enable black_1280x800.png

Image 8-81 Example of custom black level files selected

1. Make sure the Enable slider is set to the right to activate the selected black level file

CLO can not be used when the light source is off, the shutter is closed or if the Dynamic Black feature is active (if available).

How to reduce the power

1. In the main menu, select Installation → Illumination.

Image 8-82 Installation menu, illumination

The Illumination menu is displayed.

Installation Illumination UDM 4K22 Desired power 100 % Actual power 91 Maximum available power 91 Constant light output CLO Scale 77% Power limited at 91% Flex

Image 8-83 Example of the Illumination menu

1. Use the Slider to change the power value.
2. Enable the Constant light output slider if you want to enable CLO mode.

GUI - Installation

To present stereoscopic pictures, two images are projected superimposed onto the same screen through polarizing filters or presented on a display with polarized filters. For Digital Cinema, a silver screen is used so that polarization is preserved. On most passive displays every other row of pixels are polarized for one eye or the other. This method is also known as interlacing.

The viewer wears glasses which contain a pair of opposite polarizing filters. As each filter only passes light which is similarly polarized and blocks the opposite polarized light, each eye only sees one of the images, and the effect is achieved.

What is Active Stereo?

Field sequential 3D (also known as active 3D or "Active Stereo") is a technique of displaying stereoscopic 3D images. It works by only presenting the image intended for the left eye while blocking the right eye's view, then presenting the right-eye image while blocking the left eye, and repeating this so rapidly that the interruptions do not interfere with the perceived fusion of the two images into a single 3D image.

This system setup uses liquid crystal shutter glasses (also known as active shutter glasses). Each eye's glass contains a liquid crystal layer which has the property of becoming opaque when voltage is applied, being otherwise transparent. The glasses are controlled by a timing signal that allows the glasses to alternately block one eye, and then the other, in synchronization with the refresh rate of the screen. The timing synchronization to the video equipment may be achieved via a wired signal or via wireless communication, this by using either an infrared or radio frequency (e.g. Bluetooth, DLP link) transmitter.

Projection method used

This projector can only show active 3D images, used in combination with a 3D emitter and active shutter glasses. While it is allowed to connect passive stereo source signals, the image processing of the projector will convert those signals to an active 3D compatible image.

The options on the projector software allow you to fine-tune the 3D settings accordingly to the specifications of the 3D emitter.

If a 3D emitter is used that radiates IR beams, the IR beams may interfere with the IR communication between projector and the RCU. If such interference occurs, connect the RCU to the projector using the remote cable. It is also advised to turn the IR receivers on the projector off to avoid the 3D emitter interference. To turn off the IR receivers, see "Pulse RCU, function of the on/off button", page 31.

8.14.2 Setup process 3D projection

GUI - Installation

• Layout mode: Standard layout (1x1 layout)
  • Video Timing: 2560 x 1600 (WQXGA) @120 Hz
  • Color depth: 30 bpp
• Connector: DisplayPort 1.2 or HDMI

Connecting with the quad DP 1.2 Input card

You can use one of the following methods. The resulting image will always be an Active Stereo image.

Source	Layout mode	Video Timing / cable	Fixed configuration?	Color depth
Active Stereo (sequential L/R)	Standard layout (1x1 layout)	2560 x 1600 @120 Hz		30 bpp
Active Stereo (sequential L/R)	4 Column mode (4x1 layout)	960 x 2160 @120 Hz		30 bpp
Active Stereo (sequential L/R)	4 Quadrant mode (2x2 layout)	1920 x 1080 @120 Hz		30 bpp
Passive Stereo (separate L/R)	Standard layout (1x1 layout)	3840 x 2160 @60 Hz	Cable 1: left eyeCable 2: right eye	30 bpp
Passive Stereo (dual pipe L/R)	2 Column mode (2x1 layout)	1920 x 2160 @60 Hz	Cable 1: left eye, 30 bpp left columnCable 2: left eye, right columnCable 3: right eye, left columnCable 4: right eye, right column

8.14.4 3D Setup

Why change the 3D setup?

While Barco can provide a 3D emitter and active shutter glasses as options to this projector, you are also free

GUI - Installation

Source signal AutoStereo Mono ActiveStereo

2D Source Output is a 2D image Output is a 2D image Output is in Active Stereo

Active Stereo source Output is in Active Stereo Output is a 2D image Output is in Active Stereo

Passive Stereo source Output is in Active Stereo Output is a 2D image Output is in Active Stereo

When a different Display Mode is chosen compared to the source signal (e.g. Active Stereo source with Mono output), advanced image processing will make sure you a desirable image will be displayed.

If a 3D emitter is used that radiates infrared beams (IR beams), the IR beams may interfere with the IR communication between projector and the RCU. If such interference occurs, connect the RCU to the projector using the remote cable. It is also advised to turn the IR receivers on the projector off to avoid the 3D emitter interference. To turn off the IR receivers, see "Pulse RCU, function of the on/off button", page 31.

How to adjust the projector to the 3D emitter?

1. In the main menu, select Installation → 3D Setup.

Image 8-84 Installation menu, 3D setup

The 3D setup menu is displayed.

Installation Swap eyes Swap frame pair Dark time 2500 1000 1200 UDX W40

GUI - Profiles

9

9.1 Profiles introduction 116
9.2 Profiles setup parameters.... 116
9.3 Saving settings to a new profile....117
9.4 Deleting a projector profile....119

GUI - Profiles

9.1 Profiles introduction

About Profiles

The profile function makes it possible to store different profiles / projector setups for different use cases, and quickly recall them when needed. This means that it is not necessary to enter a lot of different menus to adjust the projector setup for specific recurring use cases. Due to the limited nature of this function and to avoid terminology confusion with more complex macro's, these are not called "macro's", but "profiles".

A few examples of different user cases are:

• Building temporary gaming setups in bright auditorium-level environment, versus a darker "gaming room" or "cave".
• Playing content from an old DVD versus playing the latest release from an HDR-coded Blu-Ray.
• A rental projector that can be rented out for business presentations, concerts and other events that have different but recurring forms of content.

Menu FS40-4K DisplayPort 2 Source Image Installation Profiles Settings Test patterns Status

Image 9-1

9.2 Profiles setup parameters

Available profile settings

Profile domain name	Settings saved
	P7 desired valuesP7 measured values
Warp	Warp status enabled / disabledScreen sizeWarp file selected (if available)Transport delayNote: Bow and 4 corners warp cannot be saved.
Blend	Blend mask enabled / disabledAll Masks (top / bottom / left / right) and heights (top / bottom / left / right)Blend files enabled / disabled (if available)Blend file selected (if available)
Black level	Black level file enabled / disabledBlack Level file selected (if available)Basic black level enabled / disabledBlack level settings (top / bottom / left / right)RGB gain values (Red, Green and Blue values)
PQ (HDR)	Screen luminance (unit and value)HDR Boost valueDynaBlack mode
Installation	Lens parameters (lens zoom, focus, shift and iris (if available))Orientation (mounting & projection)Scaling modePosition of motorized frame (if used).Shutter status (open or closed).
Cooling5	Selected Cooling mode

9.3 Saving settings to a new profile

How to save the current projector settings?

1 Adjust the necessary projector set up values for the actual user case as described in the specific tonics in

GUI - Profiles

Image 9-3

The Profile edit menu shows up.

Profiles Profile edit UDX 4K40 + New profile ... Aaa Bbb

Image 9-4

1. Select New profile

Profiles Profile edit UDX 4K40 + New profile ... Select domains Illumination Source Image Display RealColor Warp Blend Blacklevel PG Installation

GUI - Profiles

Profiles Profile edit UDX 4K40 + New profile ... Select domains Illumination Source Image Display RealColor Warp Blend Blacklevel PQ Installation Cooling Profile name: + CREATE Aaa

Image 9-6 Select domains

1. Select "Profile name". A keyboard will show up, and enter a proper name for the profile.
2. Select "create" and confirm by the OK button.

The new profile is now created and saved.

1. Repeat step 1 to 6 for creating of more profiles.

Recall a profile.

1. Enter the Menu/Profile

The stored profiles will be visible in the menu. Select the actual profile.

Profiles Profile edit UDX 4K40 + New profile ... Aaa Bbb

GUI - Profiles

Image 9-8 Profiles menu, edit

The edit menu is displayed.

Profiles Profile edit UDX 4K40 + New profile ... Aaa Bbb

Image 9-9 Profile edit menu

1. Select the undesired projector profile and confirm to expand it.

Profiles Profile edit UDX 4K40 + New profile ... Aaa Assign profile to preset Current Available Occupied 30 01 02 03 04 05 06 07 08 09

GUI – System Settings

10

10.1 Remote control 122
10.2 Host name - custom projector name setup....124
10.3 Communication, LAN setup....125
10.4 DMX 133
10.5 Front XLR output voltage control 135
10.6 GSM configuration.... 135
10.7 Changing the User Interface language 136
10.8 Themes 137 10.9 Unit (or equivalent) and other 100
10.9 Units (measurement) system setup 138
10.10 Controlling the backlight of the LCD Display.... 138
10.11 Date and time setup - manually.... 139
10.12 Date and time setup - automatically.... 140
10.13 Power saving settings 142
10.14 Lens features 143 10.15 Export product 144
10.15 Factory reset 144 10.16 Long Calibration 148
10.16 Lens Calibration 146 10.17 Flow brightness 140
10.17 Flex brightness 149 10.18 Picking frame Calibration 150
10.18 Rigging frame Calibration 150 10.19 Electronic Convergence 151
10.19 Electronic Convergence 151 10.20 Operational mode 153

GUI - System Settings

10.1 Remote control

10.1.1 Broadcast address

About broadcast address

Broadcast address is a common address that can be set on the projector. That can be "0" or "1". The default broadcast address is '0'.

Any command coming from an RCU programmed with that common address will be executed.

How to the broadcast address

1. In the main menu, select Settings → Communication → Remote control.

Image 10-1 Communication menu, Remote Control

The Remote control menu is displayed.

Communicati... Remote control UDX W40 Broadcast address Generic IR (0) Barco broadcast IR (1) Projector address < 1 > Remote control sensors IR Front IR Rear IR Side

GUI - System Settings

How to change

1. In the main menu, select Settings → Communication → IR control.

Image 10-3 Communication menu, Remote Control

The Remote control menu is displayed.

Communicati... Remote control UDX W40 Broadcast address ✓ Generic IR (0) □ Barco broadcast IR (1) Projector address < 1 > Remote control sensors ● IR Front ● IR Rear ● IR Side APPLY

Image 10-4 Example of the Remote control menu

1. Select the current projector address and enter a new address.
2. Select APPLY and click OK to apply the changes.

From now on the projector will only listen to this new address and to its broadcast address.

10.1.3 IR sensors

GUI - System Settings

Communicati... Remote control UDX W40 Broadcast address Generic IR (0) Barco broadcast IR (1) Projector address < 1 > Remote control sensors IR Front IR Rear IR Side APPLY

Image 10-6 Example of the IR control menu

1. To disable an IR sensor, select the slider and drag to the left.

A blue slider means an active IR sensor.

A gray slider means an inactive IR sensor.

1. Select APPLY and click OK to apply the changes.

10.2 Host name - custom projector name setup

What can be done?

The default host name of the projector is the projector type along with the serial number of your projector (e.g. "UDX-4K40-0123456789").

You can change this name to make it easier to spot in a network with multiple devices or projectors

How to set a different Host name

1. In the main menu, select Settings → Communication → Host name.

GUI - System Settings

< Communication Host name UDX W40 Host name: udx-walrus ✓ APPLY

w e r t y u i s p

a s d f g h j k l z x c v b n m . . 8723 British English * -

Image 10-8 Example of the host name menu

1. Press confirm to edit the Host name field.
2. Use the digital keyboard to change the Host name to the desired custom name.
3. Press the OK key, or press the enter icon to confirm the typed name. Click Apply to update the host name.

10.3 Communication, LAN setup

About a network connection

A network connection can be made via a wired connection or via the optional wireless unit.

10.3.1 Introduction to a Network connection

DHCP

Dynamic host configuration protocol. DHCP is a communications protocol that lets network administrators manage centrally and automate the assignment of IP addresses in an organization's network. Using the Internet Protocol, each machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users with a connection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address must be entered regularly at each computer and if computers move to another location in another part of the

GUI - System Settings

What should be set up for an Ethernet address?

Two ways can be used to assign an address:

• use the Automatic setting so that an automatic address will be assigned.

• Assign manually an IP address, Net-mask (subnet-mask), (default) gateway address.

• Set the IP-Address field to the desired value. This must NOT be 0.0.0.0 for static IP-Address assignment. The IP address identifies a projector's location on the network in the same way a street address identifies a house on a city block. Just as a street address must identify a unique residence, an IP address must be globally unique and have a uniform format.

• Set the Subnet-Mask as appropriate for the local subnet.
• Set the Default-Gateway to the IP-Address of the local router (MUST be on the local subnet!) on the same network as this projector that is used to forward traffic to destinations beyond the local network. This must not be 0.0.0.0. If there is no router on the projector's local subnet then just set this field to an IP-Address on the subnet.

10.3.2 Wired IP address set up

How to automatically set up the IP address

1. In the main menu, select Settings → Communication → LAN.

Image 10-9 Communication menu, LAN

The LAN menu is displayed.

< Communication LAN UDX W40 Automatic Connected Address 10.200.28.215 HW Address 00:04:A5:87:1C.BF

GUI - System Settings

Image 10-11 Communication menu, LAN

The LAN menu is displayed

Communication LAN UDX W40 Automatic Connected Address 10.200.28.215 HW Address 00:04:A5 87:1C BF Submit mask: 255.255.254.0 Default gateway: 10.200.28.1 Name servers: 10.197.192.11,10.193.251.11 ✓ APPLY

Image 10-12 Example of the LAN menu

1. Disable the Automatic slider. The slider becomes gray.
2. Use the arrow keys to select Address and press OK button to activate the input box.

Communication LAN UDX 4K40 Address: 192.168.1.100 Subset mask: 255.255.255.0

GUI - System Settings

10.3.3 Wireless IP address set up

When can the wireless IP address be used?

When the optional WiFi module has been installed on the projector, you can configure the projector in such a way it can access the network via WiFi instead of a LAN cable.

For more information on how to install the WiFi module, please refer to the installation manual.

How to connect to a wireless network?

1. In the main menu, select Settings → Communication → WiFi.

Image 10-14 Communication menu. WiFi

The WiFi menu is displayed.

Communication WIFI UDM 4K22 Enable Automatic FindingNemo Connected Bitrate: 1 Mbps | Max Bitrate: 270 Mbps HR Address: 00SE/EBE/FA6 SELECT NETWORK Address 192.168.8.20 Submit mask: 255.255.255.0 Default gateway: 192.168.8.1 Name servers: Name servers ✓ APPLY

Imane 10-15 Example of the WiFi menu

Tip: If the desired wireless network is not in the list or hidden by default, select Other network. A form will pop up, allowing you to fill in the details of the network.

Select WIF... Other WIFI Network UDM 4K22 SSG Security < NONE > A S D F G H J K L ✓ Z X C V S N M . . &123 British English !-)

Image 10-17 Example of the entry form to search for other wireless networks

1. If required by the chosen wireless network fill in the user name, password and confirm.

Tip: If you already connected to this network in the past using this projector, the software will remember the user name and password, ensuring you do not have to fill this in again.

1. Press Connect to connect to the selected network.
2. If required by the chosen wireless network, fill in the user name and password and confirm.

An automatic IP address is assigned.

When connected to this network, it is indicated in the upper right corner of the menu with the term "connected".

How to manually set up the IP address

1. In the main menu, select Settings → Communication → WiFi.

GUI - System Settings

Communication WIFI UDM 4K22 Enable Automatic Address 192.168.8.20 Submit mask 255.255.255.0 Default gateway 192.168.8.1 Name servers: Asname server(s) ✓ APPLY FindingNemo Connected Bitrate: 1 Mbps | Max Bitrate: 270 Mbps HIV Address: 000E RERFAA6 SELECT NETWORK

Image 10-19 Example of the WiFi menu

1. Make sure the Enable slider is set to the right to enable the WiFi module. The color of the slider becomes blue.
2. Disable the Automatic slider by setting it to the left. The switch becomes gray.

Communication WiFi UDM 4K22 Enable Automatic FindingNemo Connected Bitrate: 1 Mbps Max Bitrate: 270 Mbps HW Address: 00:00:RE:FE.A6 SELECT NETWORK Address 192.168.1.100 Submit mask: 255.255.255.0 Default gateway Default gateway Name servers Name servers ✓ APPLY

Image 10-20

GUI - System Settings

WIFI Select WIFI Network UDM 4K22 Available networks: FindingNemo C REFRESH LIST OTHER NETWORK

Image 10-21 Example of the available networks list.

1. Press Connect to connect to the selected network.
2. If required by the chosen wireless network, fill in the username and password and confirm.

When connected to this network, it is indicated in the upper right corner of the menu with the term "connected".

10.3.4 LAN over HDBaseMP address set up

LAN over HDBaseT is only supported on HDBaseInput 1 on the Pulse Quad Combo Input board Mk II.

About LAN over HDBaseT

When a LAN cable is mounted in HDBaseInput 1, the HDBaseT menu will appear in the Settings menu. Using the menu, you can assign a custom IP address, or leave the automatic IP address setup.

Keep into account that the HDBaseNetwork will be unavailable if the projector is in Standby mode or ECO mode (whichever is applicable to your projector). If you want to use this connector as your main network connection, it is thus advised to disable the standby or ECO mode. For more info, see power settings.

GUI - System Settings

Communication HDBaseT™ UDM 4K22 Automatic Address: 10.200.50.157 Subnet mask: 255.255.255.0 Default gateway: 10.200.50.1 Name servers: 10.197.192.11,10.193.251.11 ✓ APPLY Connected HW Address: 0014A5 E2RE 28 HDBaseT network unavailable in standby / ECO mode

Image 10-23 Example of the HDBaseTmenu

1. To enable Automatic, make sure the Automatic slider is set to the right. The color of the slider will be blue. An IP address will be automatically assigned if it can make a connection to the network.. When connected, it is indicated with the connection symbol and the indication Connected.
2. Select APPLY and confirm.

How to manually set up the IP address

1. In the main menu, select Settings → Communication → HDBaseT ^TM .

Image 10-24 Communication menu, HDBaseT

The HDBaseTM menu is displayed.

GUI - System Settings

Communication HDBaseT™ UDM 4K22 Address: 192.168.1.100 Subnet mask: 255.255.255.0 Default gateway: Default gateway ( ) 7 8 9 ÷ × + 4 5 6 ... ^ / - 1 2 3 ✓ % * 8 .

Image 10-26 Example of entering the IP address

1. Use the arrow keys and enter key to enter in the IP address.

Note: Digits can be entered with the digit keys on the remote control or the local keypad. When a digit is entered in that way, the next character will be selected automatically.

1. Once filled in, select the Enter symbol and confirm.
2. Repeat steps 4 and 5 for the Subnet mask and Default Gateway.
3. Select APPLY and click OK to confirm all changes.

When the connection is established, it is indicated with the connection symbol and the indication Connected.

10.4 DMX

About the ways to control the projector via DMX

DMX signals can be connected to the DMX In port on the communicator interface when using a standard DMX cable equipped with XLR connector. The DMX out can be used to create a chain of DMX devices. One universe can control up to 512 channels.

GUI - System Settings

DMX Feature	What can be done?
	If no DMX signals are available, you can reset the intensity value to its default (maximum) value of 255 using theMax Intensitybutton.
Auto power down	The projector can be forced to shut down after a certain time-out period if no DMX signals are available.Note: Value is set in minutes.
DMX Art-Net	DMX can be sent via the Ethernet connector to the projector instead of the classic DMX connector. This function can be enabled or disabled. Art-Net is generally used when more than 512 addresses are used in your setup.
DMX Art-Net Universe	Note: DMX Art-Net Universe can only be used when Art-Net DMX is enabled.If Art-Net is enabled, you can specify which DMX universe this projector belongs to.
Front XLR connector	If available on your projector, the power of the XLR connector on the front side of the projector can be enabled and set to a desired value.Note: If no front XLR connector is available on your projector, this option remains hidden.

How to set up DMX?

1. In the main menu, select System Settings → Communication → DMX.

Image 10-27 Communication menu, DMX

The DMX menu is displayed.

10.5 Front XLR output voltage control

What can be done?

The output voltage on the front XLR connector can be enabled or disabled. If enabled, the output voltage level can be set to 0 V, 12 V or 24 V.

The output voltage will depend on the application or peripheral used. For example, the optional external mechanical shutter requires 12 V. The motorized rigging frame on the other end requires 24 V.

How to enable or disable?

1. In the main menu, select System Settings → Communication → DMX.

Image 10-29 Communication menu, DMX

The DMX menu is displayed.

Communication Mode < Basic > Start Channel 1 Auto power down 10 timeout (minutes) Art-Net 0 Art-Net Universe Art-Net 0 Art-Net Net UDX W40 MONITOR XLP Connector Output Voltage: 24V 9V 12V

GUI - System Settings

About the SIM card PIN code

To configure the projector software with the installed SIM card for the first time, a correct PIN code (4 digits) must be entered.

As the PIN code cannot be checked with the one on the SIM card, ensure to enter the correct PIN code.

When your SIM card is blocked, you have to remove the SIM card from the GSM module and to insert the SIM card in a mobile phone so that you can enter the PUK code to unblock the SIM card.

How to activate

1. In the main menu, select Settings → Communication → GSM.

Image 10-31 Communication menu, GSM

At first use, the GSM pin code input menu is displayed. If a correct pin code has been entered in the past, it will not be necessary to enter the pin code again and you can skip the next step.

1. Enter the 4 digits of the PIN code and confirm.

Communication	GSM	UDM 4K22
IMEI	356136076392499
ICCID	89320269351010073370
Pin state	Accepted
Data status	REGISTERED

GUI - System Settings

The Language menu is displayed.

< User interface Language UDX 4K32 Deutsch English Español Français 日本語 한국어 Português (BR) Русский

Image 10-34 Example of the Language menu

1. Select the desired language. You can choose between the following:

• German (DE)
- English (EN)
- Spanish (ES)
- French (FR)
- Japanese (JA)
- Korean (KO)
- Portuguese (PT-BR)
• Russian (RU)
- Chinese (ZH)

10.8 Themes

About Themes

Themes are used to apply a predefined functionality to the OSD display. There are two options: light or dark (default).

GUI - System Settings

10.9 Units (measurement) system setup

About the measurement systems

You can use this menu to change the default measurement systems. By default the metric system is used. But you can choose between the following:

• Temperature: °C or °F
• Distance: meter, centimeter, feet or inch.

How to set a different metric system

1. In the main menu, select Settings → User interface → Units.

Image 10-36 Settings menu, units

The Units menu is displayed.

User interface Units UDX W40 Specify the desired units to use in the menu system Temperature °C Length Inches (in) Meters (m) Centimeters (cm)

GUI - System Settings

Image 10-38 Settings menu, backlight

The Backlight menu will be displayed.

User interface Backlight UDX W40 Long-press the "OSD off" button ( ) to toggle stealth mode. Stealth mode Off On On until reboot Backlight Off On Custom 30 seconds 1 minute The backlight will stay on

Image 10-39 Example of the backlight menu

1. Choose the desired setting for the backlights. Select one of the predetermined options, or a custom value.

10.11 Date and time setup - manually

About date and time

The date and time setting can be set manually or automatically via an NTP server based on region and city location.

GUI - System Settings

Settings Date and time FS400-HR Automatic Server NTP server Date 0 / 0 / 0 Time 0 : 0 : 0 Region Australia UTC Europe Indian Pacific City ti Kosrae Kwaialein Majuro Marquesas ✓ APPLY

Image 10-41 Example of the Date and time menu

1. Disable the Automatic slider.

Gray slider: automatic is off

Blue slider: automatic is on

1. Select Date

The Date dialog is prompted. The active day is selected by default.

1. Slide the Day, Month and Year slider up or down until the desired date is obtained.

or

Alternatively, use the up, down and OK buttons on the RCU or control panel until the desired date is obtained.

1. Select Time.

The Time dialog is prompted. The active time is selected by default.

1. Slide the Hour, Minute and second slider up or down until the desired time is obtained.

or

Alternatively, use the up, down and OK buttons on the RCU or control panel until the desired time is obtained.

GUI - System Settings

2. Enable the Automatic slider.

Settings Date and time FS400-HR Automatic Server NTP server Date 10 / 5 / 2022 Time 23 : 26 : 50 Region < Australia UTC Europe Indian Pacific > City < ti Kosrae Kwajalein Majuro Marquesas > ✓ APPLY

Image 10-43

Gray slider: automatic is off

Blue slider: automatic is on

3. Select Server and click OK.

Settings Date and time FS400-HR Automatic Server NTP server Date 10 / 5 / 2022 Q W E R T Y U I O P A S D F G H J K L Z X C V B N M . . 6433 British English

GUI - System Settings

Settings Date and time FS400-HR Automatic Server NTP server Date 10 / 5 / 2022 Time 23 : 5 : 21 Region Australia UTC Europe Indian Pacific City ast Belgrade Berlin Bratislava Brussels ✓ APPLY

Image 10-45

The list of cities is updated according the selected region.

1. Select City and select the city corresponding with your time line.
2. Select Apply to activate.

10.13 Power saving settings

Why change the power saving features?

Standby Mode exists in the projector as a power-saving feature. If the projector is projecting no image, it will automatically go to Ready and standby mode after 15 minutes each. While in standby mode, it is no longer possible to use the OSD for anything other than a status overview.

Power saving features comes at the cost of disabling projection functionality. Depending on your specific installation, you may either want to:

• increase the power-saving features to an absolute maximum (e.g. using the Standby ECO mode and reducing time-out to an absolute minimum)
• reduce the power-saving features to allow technicians to modify the projector for as long as needed, or
• disable the power saving features all together.

GUI - System Settings

The Standby mode menu is displayed.

Settings Standby mode UDM 4K22 Ready Standby ECO

Image 10-47 Example of the Standby mode menu

1. Select the desired standby mode feature, or disable it by choosing Ready.

How to change the chosen standby time-out?

1. In the main menu, select Settings → Power settings.

Image 10-48 Settings menu, Power settings

The Power settings menu is displayed.

GUI - System Settings

How to enable/disable

1. In the main menu, select System Settings → Lens Features.

Image 10-50 Settings menu, Lens features

The Lens features menu is displayed.

Settings Lens features UDX W40 Enable/Disable lens features. Availability depends on lens type. Focus Lens Shift Horizontal Lens Shift Vertical Zoom

Image 10-51 Example of the lens features menu

Depending on the mounted lens type, different functions may or may not be available such as:

• Focus
  • Horizontal lens shift
  • Vertical lens shift

• Zoom

• To enable/disable a feature, click on the slider and drag it to the left to disable the feature or the right to

Option / Domain	Setting Factory setting
	Auto power downArt-netXLR Connector	Disabled
GSM PIN State Unconfirmed
Illumination Power	100%
	Constant light output (CLO) Disabled
ImageActuator 4K Actuator enabled / disabled		Enabled
Blend Blend / Mask sizeBlack Level		Disabled, all value to zero
ImageCapture Camera Camera disabled, all measurements resetto 0
Connectors Signal range Auto
Convergence	Electronic Convergence	All values to zero
Display	Display mode	AutoStereo
Image features	Contrast	mid value
	Brightness	mid value
	Saturation	mid value
	Sharpness	mid value
	Temperature, mid value, auto	mid value

GUI – System Settings

Option / Domain	Setting Factory setting
		Note: All uploaded custom test patterns will be deleted
Uniformity DynaBlack Off
Warp Screen size	$120x3200 / 2560x1600
	4 cornerBow	Warp disabled, no warp
	Warp files Disabled	Note: all uploaded warp files will be deleted
Network Communication LAN, Automatic settings
Optics High Contrast Off
Peripheral	Settings for External Cooler	Cooling mode set to internal.
	Settings for Motorized Frame	All values to mid value
Profiles	Settings for projector profiles	All profiles will be deleted
Screen	Screen luminance unit	nits
	Screen Luminance	400
	HDR Boost	1.0
System	Auto off / Eco Mode / Standby Mode (depending on availability)	Enabled
	Ready Time-out	auto
	Operational Mode	Normal
Time	Time server Automatic disabled, NTP server removed
	Date	0 / 0 / 0
	Time	0 : 0 : 0
	Region / City	UTC

GUI - System Settings

Image 10-52 Settings menu, factory reset

The Reset menu is displayed.

Maintenance Factory reset UDM 4K22 Factory reset Reset domains OMX Display 3D illumination Image features Test patterns * imageActuator Orientation Uniformity Blend * RealColor * P7 Warp * Connectors * Resolution Network Convergence Source Optics

Image 10-53 Example of the reset menu

1. In the Reset menu, select RESETALL and confirm with OK.

How to reset one or more projector settings

1. In the main menu, select Settings → Maintenance → Reset.

GUI - System Settings

Multiple selections are possible.

1. Select RESET SELECTED and confirm with OK to reset all selected settings.

10.16 Lens Calibration

How to calibrate

1. In the main menu, Settings → Maintenance → Lens Calibration.

Image 10-56 Maintenance menu, lens calibration

The Lens Calibration menu is displayed, alongside the status of each

Maintenance Lens calibration UDX W40 ✓ ✓ Zoom Focus Unknown Unknown Lensshift Horizontal Lensshift Vertical

Image 10-57 Example of the lens calibration menu

GUI - System Settings

Maintenance Lens calibration UDX W40 ✓ Zoom ✓ Focus Calibrating Lensshift Horizontal Unknown Lensshift Vertical

Image 10-58 example of calibration in progress

When an error is detected, the message Calibration Error is displayed next to function.

10.17 Flex brightness

This feature is available by default on the following devices: UDM 4k22, UDM W22. This feature is also available as an option on the following devices: UDM 4K15, UDM W19, UDM W15.

Overview

With the FLEX technology the projector owners can lock the light output to different levels. The locking can be done via 3 different ways:

• Via Projector Toolset when connected via an ethernet connection with the projector. For more information on how to set up and use the Flex license, see the Projector Toolset's user guide, chapter "Configuration, License / registration".
• Via Barco Insights Management Suite when the GSM module is installed. For more information on how to set up and use the Flex license, see Projector Management Suite user guide, chapter "Projector Configuration tab" – "Flex brightness"

(1) 4.0000

GUI - System Settings

Maximum Light output setup via OSD menu

1. In the main menu, select Settings → Maintenance → Flex.

Image 10-59 Maintenance menu, Flex

The Flex license menu is displayed.

Maintenance Flex UDM 4K22 Max light output < 3000 19000 20000 21000 22000 PIN:

Image 10-60 Example of the Flex license menu

1. Choose the desired Light output (in lumens) for which you have a code available.
2. Enter the code via the OSD menu and confirm.

< Maintenance Flex License UDX 4K32 Max light output < 10 Enter PIN 26000 27000

GUI - System Settings

Image 10-62 Maintenance menu, Frame calibration

The Frame calibration menu is displayed.

Maintenance Frame Calibration F80-4K9 ✓ Horizontal shift Vertical shift Rotation

Image 10-63 Example of the Frame calibration menu

1. In the Frame Calibration menu, select the desired calibration action and click OK.

You can select one of the following functions:

• Horizontal shift
- Vertical shift
- Rotation

The text Calibrating will be displayed until the calibration is completed.

GUI - System Settings

Image 10-65 Maintenance menu, electronic convergence

The Electronic Convergence menu is displayed.

Maintena... Electronic Convergence UDX W40 Red x y 0 0 Green 0 0 Blue 0 0 RESET

Image 10-66 Example of the electronic convergence menu

1. Select the desired X or Y value for one of the three colors and confirm.
2. Use the arrow keys to raise or lower the value and confirm.
3. Confirm all changes by pressing Enter.

Pure black background with faint white diagonal lines and a small dark triangular symbol in the top-right corner (no text or symbols)

10.20 Operational mode

Overview

The UDM range now offers you a possibility to choose the most relevant user mode for your application. You can select, setup and tweak the mode which you need, while a smart monitoring algorithm in the background keeps on balancing and optimizing between illumination output power, minimal noise level and optimized temperature household.

These are the presets being offered to start from:

1. "Normal mode": This is the standard mode delivering highest possible brightness while ensuring a life time of 20 000 hours and keeping the noise level around 48 dBA.
2. "Silent mode": controlling maximal fan speed staying 47 dBA.

How to change the operational mode of your projector

1. In the main menu, navigate to Settings → System → Operational mode.

Image 10-68 Maintenance menu, operational mode

The Operational Mode menu is displayed.

System Operational modes UDM 4K22 Normal 4 Silent

GUI - System Settings

10.21 Capture mode

Why use capture mode?

Various technical features are used inside the projector to display the best possible image on the projected surface. However, in expositions and setups where visitors are expected to film or take pictures of the projected surface, some of these technical features may have side-effects on the captured footage, such as solarization.

Enabling the Capture mode feature disables some of the technical features of the projector that are known to cause solarization and gives the visiting audience an experience they can "capture" and post on social media without worries.

How to enable Capture mode

1. In the main menu, navigate to Settings → System.
2. In the Lens menu, click Capture mode to toggle between On and Off.

Image 10-70 System menu, Capture mode disabled Image 10-71 System menu, Capture mode enabled

10.22 Login to advanced settings

How to login

1. In the main menu, Settings → Maintenance → Login.

There are 2 ways to login:

• Via user & password, go to step 2
• Via a digit code, go to step 5

1. To login via user & password, select User and click OK.
2. Navigate to user name and click OK.

A keyboard is displayed. Enter the user name

Navigate to Password and enter the password.

1. Select LOGIN and click OK to login.
2. To login via digit code, select digit keyboard and click OK.
3. Navigate to Pin code and click OK.

A keyboard is displayed. Enter the pin code.

10.23 List of open source licenses

About open source licenses

Open source licenses are licenses that comply with the Open Source Definition. In brief, they allow software to be freely used, modified, and shared.

To be open and transparent about the open source software used on the projector, there is a list of all open source licenses available in the software.

How to find the open source licenses

For the complete and most up-to-date list of the used open source software and the version used, go to the main menu and select Settings → General → Open source licenses.

GUI - System Settings

Advanced Settings

11

11.1 Remote access – Enable source preview 158
11.2 Remote access – Enable camera preview 159
11.3 Advanced Settings - Color 160
11.4 Advanced Settings – Statistics.... 161
11.5 Checking the status of the Laser Banks 162
11.6 Advanced settings – Tilt sensor calibration 163

About the Advanced Settings menu

The Advanced Settings and Remote access menus are hidden by default for the regular user. you can only make these menus visible after entering a User name and Password or a Service code with the remote control. See "Login to advanced settings", page 154 for more info.

Advanced Settings

11.1 Remote access - Enable source preview

Source preview

Up until Pulse software 2.0. x, you were able to see a preview of the connected source when you remotely accessed the projector. This was a feature you could disable using Projector Toolset.

However, from Pulse 2.1. x onward, this feature is disabled by default and can now be enabled in both Projector Toolset and the Pulse GUI.

Upgrading your projector from a software version 2.0.x or older to 2.1.x or newer will disable Source preview by default. Once the software has been successfully upgraded, you can always opt to enable this feature again.

How to enable source preview

1. In the main menu, select Settings → Maintenance and login to visualize the hidden Remote access menu.
2. Select Remote access.

Image 11-2 Maintenance menu, Remote access

The Remote access menu is displayed.

Maintenance Remote access UDM 4K22 Source preview

11.2 Remote access - Enable camera preview

Camera preview

Up until Pulse software 2.0.x, you were able to see the footage of the camera when you remotely accessed the projector. This was a feature you could disable using Projector Toolset.

However, from Pulse 2.1. x onward, this feature is disabled by default and can now be enabled in both Projector Toolset and the Pulse GUI.

Upgrading your projector from a software version 2.0.x or older to 2.1.x or newer will disable Camera preview by default. Once the software has been successfully upgraded, you can always opt to enable this feature again.

How to enable Camera preview

1. In the main menu, select Settings → Maintenance and login to visualize the hidden Remote access menu.
2. Select Remote access.

Image 11-5 Maintenance menu, Remote access

The Remote access menu is displayed.

Maintenance Remote access UDX 4K22 Camera preview Source preview

Advanced Settings

11.3 Advanced Settings - Color

CAUTION: The native colors have been measured and set during factory production. Do not change them, unless parts of the optical path have been replaced due to servicing. If you need to change the native colors on the device, make sure to also perform a P7 calibration, using the Projector Toolset and a chroma meter. For more info on P7 calibration, refer to the Projector Toolset Reference guide.

How to adjust the P7 native settings

1. In the main menu, navigate to Settings → Maintenance → Advanced, while you are logged in.

Image 11-8 Maintenance menu, Advanced

1. In the Advanced Settings menu, select Native RealColor.

Image 11-9 Advanced Settings, Native Realcolor

The RealColor calibration menu will be displayed.

< Advanced

RealColor calibration

UDX 4K22

11.4 Advanced Settings – Statistics

What can be seen?

The statistics screen shows the general information about the projector, spread over two tab pages.

The following items will be displayed:

- Laser runtime

- Laser Strikes

- Laser bank x runtime

- Projector runtime

- System runtime

- System uptime

How to display the statistics

1. In the main menu, navigate to System Settings → Maintenance → Advanced Settings, while you are logged in.

Image 11-11 Maintenance menu, Advanced

1. In the Advanced Settings menu, select Statistics.

Image 11–12 Advanced settings, Statistics

Advanced Settings

11.5 Checking the status of the Laser Banks

About failing laser banks

The projector is powered by a laser light source, which has multiple laser banks. The light output and color performance is dependant on the number of active laser banks.

If one or more laser banks have failed of a certain type, you will notice a decreased light input and decrease in color performance. But the projector will keep on playing, unless too many banks of a certain color will have failed.

In order to disable a certain laser bank, or calibrate the projector after disabling one or more laser banks, please refer to the Projector Toolset User Manual.

How to check the status of the Laser Banks

1. In the main menu, navigate to Settings → Maintenance → Advanced, while you are logged in.

Image 11-14 Maintenance menu, Advanced

1. Enter the service code.
2. In the Service menu, select Laser Banks.

Image 11–15 Advanced menu, Laser banks

Advanced Settings

Laser grou... Laser bank group 0 F80-4K12 Enable notifications for this group Bank 1 Operational Bank 3 Operational Bank 2 Operational Bank 4 Operational

Image 11-17 Example of the laser bank group menu

1. If you want notifications to be disabled for a specific group of laser banks, disable the Enable notifications for this group slider.

11.6 Advanced settings - Tilt sensor calibration

CAUTION: The calibration procedure resets the values of the tilt sensor to 0 in the current position of the projector. For the optimal working of the tilt sensor it is important to make sure the projector is perfectly level when performing this procedure. If not, the tilt sensor will not function as desired once the calibration has been completed.

Required tools

Level

How to calibrate the tilt sensor?

1. Place the projector on a flat surface and make sure it is positioned level in all directions. Use a level tool to help ensure this.
2. In the main menu navigate to Settings → Maintenance → Advanced while you are logged in

Advanced Settings

Maintenance Advanced UDM 4K22 Confirm action Are you sure you want to calibrate the tilt sensor to zero in the current projector position? ✓ CONFIRM × CANCEL Tilt sensor callt

Image 11-20 Example of the Advanced menu with the Tilt sensor menu

The tilt sensor will be set to zero in the current position of the projector.

GUI – Status menu

12

12.1 Status menu overview....166

No settings can be modified in the status menu. Its only for consulting.

GUI - Status menu

12.1 Status menu overview

How to access the status menu

While in the main menu, press Status.

Image 12-1 Main menu, status

The status menu is displayed.

Menu Status UDX 4K40 L1 HDMI L1 HDMI: No signal Display mode: Mono Transport delay: 0 Frequency: 60.9 Hz Output resolution: 8K UHD PUB mode: 1.15Ω/Hz

Image 12-2 Example of the first page of the status menu

Swipe the screen left of right to swap between the Status pages.

What can be seen on the About page?

• Projector information, e.g. firmware version, serial number, projector article number and registration status (only if applicable for your device)
• Mounted lens: Lens type and Lens description (if available).
• Installation information: Altitude, pitch angle, roll angle, distance (only if applicable for your device)
• Basic statistics, Light source run time, light source strikes, projector runtime.

GUI - Status menu

Product maintenance

13

13.1 Software update 170
13.2 Cleaning the lens 171
13.3 Cleaning the exterior of the projector 172
13.4 Cleaning / replace the air filters....172

About this chapter

This chapter contains general maintenance procedures.

Product maintenance

13.1 Software update

CAUTION: Do not power off or unplug the projector while the software update is ongoing.

How to update the software

1. Power on the projector. Wait until the Power on/off button is lit white or blue.
2. Download and install the latest version of Projector Toolset for Pulse. The program can be downloaded for free from Barco's website, (URL: http://www.barco.com). Click on myBarco and log in to get access to secured information. Registration is necessary.

If you are not yet registered, click on New to myBarco and follow the instructions. With the created login and password, it is possible to log in where you can download the software.

1. Download the latest firmware (format .fw) from Barco's website in the same way as for Projector Toolset.
2. Start Projector Toolset and make a connection with the projector. For more information, see the "Projector Toolset" user guide.
3. Select tab Update settings.
4. Fill out the path to the update file (1)

Update Settings Update File (1) Update (2)

Update Settings Update File DrTemp/Firmware/Internet 2.0.6.f% Update (3) Question: Note: Upgrading the projector will take a long time. Please check the manual for implications upgraded this projector.

1. Click Yes to continue (4).

The update file will be transferred to the projector and installed. The projector will reboot.

A message is displayed. Click Ok to clear the message.

How to update the software if the projector isn't connected to the network

1. Power on the projector. Wait until the Power on/off button is either lit white or blue.
2. Download the latest firmware file ( format .fw) from Barco's website. The firmware can be downloaded for free from Barco's website, (URL: http://www.barco.com). Click on myBarco and log in to get access to secured information. Registration is necessary.

If you are not yet registered, click on New to myBarco and follow the instructions. With the created login and password, it is possible to log in where you can download the software.

1. Place the firmware file on a clean USB flash drive.

Note: Make sure the flash drive is FAT32 compatible & no other files are on the flash drive.

1. Plug the flash drive in the USB port on the Communication Panel.

The update file will be transferred to the projector and installed. The projector will reboot when completed.

CAUTION: While it is technically possible to "downgrade" the software to an older version using this method, it is NOT recommended and should be avoided as much as possible. Certain features will no longer be supported, projectors can display unwanted behavior during the downgrade and in some rare cases, this may even bring damage to the device. Always contact Barco if you want to make sure a downgrade will not hurt your device.

Take note that the update process can take a long time to complete.

For more info about the Projector Toolset see user guide of the Projector Toolset.

13.2 Cleaning the lens

Product maintenance

1. If there are still fingerprints on the surface, wipe them off with lens cleaner together with a clean lens cleaning cloth. Polish again with a dry one.

If smears occur when cleaning lenses, replace the cloth. Smears are the first indication of a dirty cloth.

13.3 Cleaning the exterior of the projector

How to clean the exterior of the projector?

1. Switch off the projector and unplug the projector from the mains power net.
2. Clean the housing of the projector with a damp cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution.

13.4 Cleaning / replace the air filters

About the air filters

There are three air filters in the projector; at the front, at the top and on the right side of the projector. It is no regular interval for cleaning or replace the filters, but they must be inspected regularly to avoid clogging, and by that also a possibility of increased temperature internally in the projector.

Cleaning of the filters

The top-, and side filter can be rinsed with lukewarm water and dried.

The filter in the front can be vacuum cleaned.

About the cover locks

All the covers are fastened to the projector by "easylock" tabs. The procedure below shows the technique for releasing and locking of the tabs.

Required tools

Flat screwdriver 5mm

Product maintenance

Diagram showing a red arrow pointing to a document with a magnified view, indicating transformation or change in the process.

Image 13-3

If the top cover do not have "easylocks" for the filter cover (older UDM models), the filter must be serviced by authorized Barco personnel.

The filter also can be vacuum cleaned from the outside, with less cleaning efficiency.

Removing the top filter

1. Unlock the "easylock", and flip the filter cover up.

Technical line drawing of a mechanical device with internal components and a directional arrow (no text or symbols)

Image 13-4

1. Remove the filter from the projector.

Product maintenance

Technical line drawing of a mechanical device with two red arrows pointing to internal components (no text or symbols)

Image 13-6

1. Remove the filter from the projector.

Technical line drawing of a computer tower with ventilation slots and drive bays (no text or symbols)

Image 13-7

1. Clean the filter with lukewarm water, and let dry.
2. Reinstall the filter in to the correct position.
3. Reinstall the side cover in the correct position, and press the "easylock"s

Note: Ensure that the cover is in correct position, and correctly locked to the projector.

Product maintenance

Technical line drawing of a mechanical component with internal structure (no text or symbols)

Image 13-9

1. Vacuum clean the filter.
2. Reinstall the filter in the front cover.
3. Reinstall the front cover in the correct position, and press the "easylock"s

Note: Ensure that the cover is in correct position, and correctly locked to the projector.

Product maintenance

Specifications

A

A.1 Specifications SDI inputs....178
A.2 Specifications HDMI inputs....178
A.3 Specifications HDBaseT inputs 179
A.4 Specifications DisplayPort 1.2 inputs....180
A.5 Specifications SFP inputs....181

About this chapter

This chapter gives an overview of the projector specifications

A.1 Specifications SDI inputs

For readability, the video timings listed are summarized. For the full list of video timings, refer to the appendices.

HD-SDI follows the SMPTE 292M standard.

3G SDI follows the SMPTE 425M standard Level A.

12G-SDI ^7 follows the SMPTE ST-2082-1 and ST-2082-10 standards.

SDI specifications

Specification	Value
Color space YCbCr
Color depth 10 bpc
Chroma sampling 4:2:2
Audio not supported
For future release	• 3D support• Interlaced support• Segmented frame support
Video timings progressive8	Type Port type Format
	HD-SDI Single link	Quad link	• Up to 1920 x 1080 @24 Hz• Up to 1920 x 1080 @25 Hz• Up to 1920 x 1080 @30 Hz• Up to 1280 x 720 @50 Hz• Up to 1280 x 720 @60 Hz
	3G-SDI Level A	Single link Quad link	Up to 2048 x 1080 @50 HzUp to 2048 x 1080 @60 Hz
	3G-SDI “BarcoLink”	Single link Quad link	1920 x 1200 @50 Hz, @59.94 Hz and @60 Hz
	12G-SDI (Channel	Single link 3840 x	2160 @50 Hz and @60 Hz

Specifications

Specification	Value
	HDCP 2.2RGB 4:4:4
Color space	YCbCr 4:2:0YCbCr 4:2:2YCbCr 4:4:4RGB 4:4:4
Color depth	24 bpp30 bpp36 bpp
3D support	Field sequential 3D (Active 3D)- Frame-packed- Top Bottom progressive- Side-by-side progressivePassive 3D not supported.
For future release	Interlaced support
Audio Not supported
Video timing§	Up to 4096 x 2160 @24 HzUp to 4096 x 2160 @25 HzUp to 4096 x 2160 @30 HzUp to 2048 x 1080 @48 HzUp to 4096 x 2160 @50 HzUp to 4096 x 2160 @60 Hz
Native video timings	UDM-W: 1920 x 1200 @60 HzUDM-4K: 3840 x 2400 @60 Hz

A.3 Specifications HDBaseT inputs

For readability, the video timings listed are summarized. For the full list of video timings, refer to the

Specifications

Specification Value
Video timings progressive8	Layout mode Supported formats
	Standard layout (1x1 layout)	• Up to 4096 x 2160 @24 Hz• Up to 4096 x 2160 @25 Hz• Up to 4096 x 2160 @30 Hz• Up to 2048 x 1080 @48 Hz• Up to 2560 x 1600 @50 Hz• Up to 2560 x 1600 @60 Hz
	2 Column mode (2x1 layout)	• 1920 x 2160 @50 Hz• 1920 x 2160 @60 Hz• 2048 x 2160 @50 Hz• 2048 x 2400 @60 Hz
Native video timings• UDM-W: 1920 x 1200 @60 Hz• UDM-4K: 3840 x 2160 @60 Hz

CAUTION: The HDBaseT inputs can bridge a distance of 100 m but are sensitive to radiated electromagnetic interference: radiated electromagnetic interference (e.g. from GSM or switching inductive or capacitive loads) within the limits of electromagnetic compatibility requirements of 3 V/m can cause random flashes or temporary loss of the projected image. As such, shielded CAT-6 cables with metal RJ-45 connectors are recommended; choose cable length no longer than required and route HDBT cable optimally screened from possible sources of electromagnetic emission.

A.4 Specifications DisplayPort 1.2 inputs

For readability, the video timings listed are summarized. For the full list of video timings, refer to the appendices.

DisplayPort 1.2 specifications

Pixel rate Up to 600 MHz pixel clock

Specifications

2D Standard layout (1x1 layout)		• Up to 4096 x 2160 @24 Hz• Up to 4096 x 2160 @30 Hz• Up to 2048 x 1080 @48 Hz• Up to 4096 x 2160 @50 Hz• Up to 4096 x 2160 @60 Hz• Up to 2560 x 1600 @120 Hz
2D 2 column mode (2x1 layout)		• 1920 x 2160 @60 Hz• 1920 x 2160 @120 Hz• 1920 x 2400 @60 Hz• 2048 x 2160 @60 Hz• 2048 x 2160 @120 Hz
2D 4 quadrant mode (2x2 layout)		• 960 x 1080 @120 Hz• 960 x 1200 @120 Hz• 1280 x 1080 @60 Hz• 1280 x 1080 @120 Hz• 1280 x 1600 @60 Hz• 1280 x 1600 @120 Hz• 1920 x 1080 @120 Hz• 1920 x 1200 @120 Hz• 2048 x 1080 @120 Hz
2D 4 column mode (4x1 layout)		• 960 x 2160 @120 Hz• 960 x 2400 @120 Hz• 1024 x 2160 @60 Hz
Active 3D	Standard layout (1x1 layout)	• 1600 x 1200 @120 Hz• 2560 x 1080 @120 Hz• 2560 x 1600 @120 Hz
Active 3D	2 column mode (2x1 layout)	1920 x 2160 @120 Hz
Active 3D	4 quadrant mode (2x2 layout)	• 1920 x 1080 @120 Hz• 1920 x 1200 @120 Hz• 2048 x 1080 @120 Hz

Specifications

SFP specifications

Color space YCbCr
Color depth 10 bpc
Chroma sampling 4:2:2
Audio support not supported
Video timings progressive ^12	Type Port type	Format
	HD-SDI Single link		Up to 1920 x 1080 @24 HzUp to 1920 x 1080 @25 HzUp to 1920 x 1080 @30 HzUp to 1280 x 720 @50 HzUp to 1280 x 720 @60 HzUp to 1280 x 720 @24 HzUp to 1280 x 720 @30 HzUp to 1280 x 720 @25 Hz
	3G-SDI Single link	1920 x 1080 @50	Hz and @60 Hz1920 x 1200 @50 Hz, @59.94 Hz and @60 Hz.2048 x 1080 @50 Hz and @60 Hz
	12G-SDI Single link	3840 x 2160 @50	Hz and @60 Hz4096 x 2160 @50 Hz and @60 Hz3840 x 2400 @50 Hz, @59.94 and @60 Hz

Video timing tables

B

B.1 Overview video timings 184
B.2 Overview video timings SDI Inputs 185
B.3 Overview video timings HDMI 2.0 inputs....186
B.4 Overview video timings DisplayPort 1.2 inputs 188
B.5 Overview video timings HDBaseT inputs 190

About this chapter

This chapter contains the tables with video timings for video interfaces.

Video timing tables

B.1 Overview video timings

List of compatible signals

The following table specifies the video signals that the projector can project. Barco Events projectors supports the signal with "X" in the Compatible signals column.

Note: Support for refresh rates 24.00, 30.00, 60.00 Hz automatically includes support of 1/1.001 x those refresh rates.

Resolution	Vertical refresh rate (Hz)	Compatible signal
		HDMI 2.0 Inputs	12G SDI Input on Mk II Input board & Fiber Network Inputs	3G SDI Inputs	DisplayPort 1.2 Inputs	HDBaseT & HDMI 1.4 Inputs
640 x 480	60 X — — X	X
720 x 480	60 X — — —	X
720 x 576	50 X — — —	X
800 x 600	60 X — — X	X
1024 x 768	60 X — — X	X
1280 x 720	24 — X X —	—
1280 x 720	25 — X X —	—
1280 x 720	30 — X X —	—
1280 x 720	50 X X X X	X
1280 x 720	60 X X X X	X
1280 x 800	60 X — — X	X
1280 x 960	60 X — — X	X
2048 x 1080	30 X — —	X X
2048 x 1080	48 X — —	X X
2048 x 1080	50 X X X X	X
2048 x 1080	60 X X X X	X
2048 x 1080	120 — — —	X —
2560 x 1600	50 X — —	X X
2560 x 1600	60 X — —	X X
2560 x 1600	120 — — —	X —
3840 x 2160	24 X — —	X X
3840 x 2160	25 X — —	X X
3840 x 2160	30 X — —	X X
3840 x 2160	50 X X —	X —
3840 x 2160	60 X X —	X —
3840 x 2400	50 X — —	X —
3840 x 2400	60 X — —	X —
4096 x 2160	24 X — —	X X
4096 x 2160	25 X — —	X X
4096 x 2160	30 X — —	X X

Video timing tables

Video timing(active pixels x active lines)	Vertical refresh rate (Hz) ^14	Type Port Type
1280 x 720 60 HD-SDI Single Link & Quad Link
1920 x 1080 24 HD-SDI Single Link & Quad Link
1920 x 1080 25 HD-SDI Single Link & Quad Link
1920 x 1080 30 HD-SDI Single Link & Quad Link
1920 x 1080 50 3G-SDI Single Link & Quad Link
1920 x 1080 60 3G-SDI Single Link & Quad Link
1920 x 1200 50 3G-SDI "BarcoLink" Single Link & Quad Link
1920 x 1200 59.94 3G-SDI "BarcoLink" Single Link & Quad Link
1920 x 1200 60 3G-SDI "BarcoLink" Single Link & Quad Link
2048 x 1080 50 3G-SDI Single Link & Quad Link
2048 x 1080 60 3G-SDI Single Link & Quad Link
3840 x 2160 50 12G-SDI		^15	Single Link
3840 x 2160 60 12G-SDI		^15	Single Link
3840 x 2400 50 12G-SDI "BarcoLink 4k" ^15			Single Link
3840 x 2400 59.94 12G-SDI "BarcoLink 4k" ^15			Single Link
3840 x 2400 60 12G-SDI "BarcoLink 4k" ^15			Single Link
4096 x 2160 50 12G-SDI		^15	Single Link
4096 x 2160 60 12G-SDI		^15	Single Link

Video timing tables

Video timing(active pixels x active lines)	Vertical refresh rate (Hz)	3D support?
1024x 768 60
1280 x720 50 Frame	packing	Top - bottom
1280 x 720 60 Frame	packing	Top - bottom
1280 x 800 60
1280 x 960 60
1280 x1024 60
1400 x 1050 60
1600 x 1200 60
1920 x 1080 24 Frame	packing	Top - bottom
1920 x 1080 25
1920 x 1080 30
1920 x 1080 50 Side	by Side (SbS) progressive
1920 x 1080 60 Side	by Side (SbS) progressive
1920 x 1200 50
1920 x 1200 60
2048 x 1080 24
2048 x 1080 25
2048 x 1080 30
2048 x 1080 48

Video timing tables

Video timing(active pixels x active lines)	Vertical refresh rate (Hz)	3D support?
4096 x 2160 50
4096 x 2160 60

B.4 Overview video timings DisplayPort 1.2 inputs

Overview

The following standard video formats are available for the projector.

Note: support for refresh rates 24.00, 30.00, 60.00 Hz automatically includes support of 1/1.001 x those refresh rates

Video timing(active pixels x active lines)	Vertical refresh rate (Hz)	Available layout modes,other than standardlayout (1 x 1 layout)	Support for 3D?
640 x 480 60
800 x 600 60
960 x 1080 120	4 Quadrant mode (2 x 2 layout)	2	Active 3D
960 x 1200 120	4 Quadrant mode (2 x 2 layout)	2	Active 3D
960 x 2160 120	4 Column mode (4 x 1 layout)	2	Active 3D
960 x 2400 120	4 Column mode (4 x 1 layout)	2	Active 3D
1024x 768 60
1024 x 2160 60	4 Column mode (4 x 1 layout)

Video timing tables

Video timing(active pixels x active lines)	Vertical refresh rate(Hz)	Available layout modes,other than standardlayout (1 x 1 layout)	Support for 3D?
1280 x 1600 120	4 Quadrant mode (2 x layout)	2	Active 3D
1400 x 1050 60
1600 x 1200 60
1600 x 1200 120	Active 3D
1920 x 1080 50
1920 x 1080 60
1920 x 1080 120	4 Quadrant mode (2 x layout)	2	Active 3D
1920 x 1200 50
1920 x 1200 60
1920 x 1200 120	4 Quadrant mode (2 x layout)	2	Active 3D
1920 x 2160 60 2	Column mode (2 x 1 layout)	2	Passive stereo
1920 x 2160 120	2 Column mode (2 x 1 layout)	2	Active 3D
1920 x 2400 60 2	Column mode (2 x 1 layout)	2	Active 3D
2048 x 1080 24
2048 x 1080 25
2048 x 1080 30
2048 x 1080 48

Video timing tables

Video timing(active pixels x active lines)	Vertical refresh rate (Hz)	Available layout modes,other than standardlayout (1 x 1 layout)	Support for 3D?
3840 x 2160 25
3840 x 2160 30
3840 x 2160 50
3840 x 2160 60	Passive Stereo
3840 x 2400 50
3840 x 2400 60
4096 x 2160 24
4096 x 2160 25
4096 x 2160 30
4096 x 2160 50
4096 x 2160 60

B.5 Overview video timings HDBaseT inputs

Overview

The following standard video formats are available for the projector.

Note: support for refresh rates 24.00, 30.00, 60.00 Hz automatically includes support of 1/1.001 x those refresh rates.

Video timing(active pixels x active lines)	Vertical refresh rate (Hz)
640 x 480 60
720 x 480 60

Video timing tables

Video timing(active pixels x active lines)	Vertical refresh rate (Hz)
1920 x 1080 60
1920 x 1200 50
1920 x 1200 60
1920 x 2160 50
1920 x 2160 60
2048 x 1080 24
2048 x 1080 25
2048 x 1080 30
2048 x 1080 48
2048 x 1080 50
2048 x 1080 60
2048 x 2160 50
2048 x 2160 60
2560 x 1600 50
2560 x 1600 60
3840 x 2160 24
3840 x 2160 25
3840 x 2160 30
4096 x 2160 24
4096 x 2160 25
4096 x 2160 30

Video timing tables

DMX chart

C

C.1 DMX chart input board positioning 194
C.2 DMX chart, Basic....194
C.3 DMX chart, Extended....195

DMX chart

C.1 DMX chart input board positioning

About the input boards

6 Input selection ranges are reserved in the DMX chart per input board location (named L1 and L2). With the current version of DMX support, it is important to take into account to keep the input boards in their original slots.

Image C-1

1 Slot L1, here filled with the Quad combo Input board
2 Slot L2, here filled with the Quad DP 1.2 Input board

C.2 DMX chart, Basic

Overview

Ch. Function Value Default Action
1 Shutter + Intensity 0	-7 255 Close shutter
	8 - 255		Adjust intensity
2 Function select	0 - 7	0 No function
	8 - 15
	16 - 23
	24 - 31
	32 - 39

DMX chart

Ch.	Function Value	Default Action
		136 - 143	Select input	7: Quad DP board Input A (if held for 1 second) ^20
		144 - 151	Select input	8: Quad DP board Input B (if held for 1 second) ^20
		152 - 159	Select input	9: Quad DP board Input C (if held for 1 second) ^20
		160 - 167	Select input	10: Quad DP board Input D (if held for 1 second) ^20
		168 - 175	Select input	11: Quad DP board Inputs A-B (if held for 1 second) ^20
		176 - 183	Select input	12: Quad DP board quad column mode (if held for 1 second)
		184 - 207	Reserved fo	future functionality
		208 - 115	Power on / Power down	Light source on (If held for 5 seconds)
		216 - 223		/ Light source off (if held for 5 seconds)
		224 - 255	Reserved fo	future functionality

C.3 DMX chart, Extended

Overview

Ch.	Function Value	Default Actions
1	Shutter + Intensity 0	-7 255	Close shutter
		8 - 255
2	Brightness	0 - 255	128	Adjusts the brightness between 0 and 100% on input.
3	Contrast	0 - 255	128	Adjusts the contrast between 0 and 100% on input
4	Input selection	0 - 7	0 No function
		8 - 15
		128 - 135	Select input	6: Quad SDI input (if held for 1 second) ^19
		136 - 143	Select input	7: Quad DP board Input A (if held for 1 second) ^20
		144 - 151	Select input	8: Quad DP board Input B (if held for 1 second) ^20
		152 - 159	Select input	9: Quad DP board Input C (if held for 1 second) ^20
		160 - 167	Select input	10: Quad DP board Input D (if held for 1 second) ^20
		168 - 175	Select input	11: Quad DP board Inputs A-B (if held for 1 second) ^20
		176 - 183	Select input	12: Quad DP board quad column mode (if held for 1 second) ^20
		184 - 255	Reserved for	future functionality
5 Focus (MSB) 0 - 255		128 Set coarse lens focus adjustment ^21
6 Focus (LSB) 0 - 255		128 Set fine lens focus adjustment ^21
7 Zoom (MSB) 0 - 255		128 Set coarse lens zoom adjustment ^21
8 Zoom (LSB) 0 - 255		128 Set fine lens zoom adjustment ^21
9 Lens shift vertical (MSB)		0 - 255	28 Set coarse lens shift in vertical direction
10 Lens shift vertical (LSB)		0 - 255	28 Set fine lens shift in vertical direction
11 Lens shift horizontal (MSB)		0 - 255	28 Set coarse lens shift in horizontal direction
12 Lens shift horizontal (LSB)		0 - 255	28 Set fine lens shift in horizontal direction
13 Light Source Power ^22		0	0 Set light source to 100%
		1 - 61

1%

DMX chart

Ch.	Function Value	Default Actions
		24 - 31	Calibrate lens	(zoom, focus and shift) (if held for 5 seconds)
		32 - 255	Reserved for	future functionality

DMX chart

WiFi & GSM compliance information

D.1 Compliance FCC 200
D.2 Compliance IC....200
D.3 KCC Certification 201

About this chapter

This chapter contains important compliance information related to the WiFi and GSM module.

Regulatory information for US and Canada can be accessed in the OSD of the projector. In order access it, select System Settings → Regulatory Information → Country.

WiFi & GSM compliance information

D.1 Compliance FCC

Federal Communication Commission Interference Statement

You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation of the device.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

D.2 Compliance IC

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

D.3 KCC Certification

KCC 인증

WiFi & GSM compliance information

Regulatory information

E

E.1 Product compliance 204
E.2 China RoHS compliance 205
E.3 Taiwan RoHS compliance....206
E.4 Turkey RoHS Compliance 207 E.5 Disposal information 207
E.6 Contact information 208
E.7 Production address....208

Regulatory information

E.1 Product compliance

UK Compliance

This product is fit for use in the UK.

Authorised Representative: Barco UK Ltd

Address: Building 329, Doncastle Road

Bracknell RG12 8PE, Berkshire, United Kingdom

EurAsian Conformity (EAC)

This product complies with the Safety of Low-Voltage Equipment (LVE Technical Regulation 004/2011, CU TR 004/2011) and the Electromagnetic Compatibility of Technical Products (EMC Technical regulation, CU TR 020/2011)

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference at his own expense

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment

FCC responsible: Barco Inc.

3059 Premiere Parkway Suite 400

30097 Duluth GA, United States

Tel: [phone]

EMC notices

FN55032/CISPR32 Class Δ MMF (MultiMedia Equipment)

E.2 China RoHS compliance

中国大陆 RoHS (Information for China ROHS compliance)

According to the "Management Methods for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products" (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco's product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section "Limit Requirements of toxic substances in Electronic Information Products".

零件项目(名称)Component name	有毒有害物质或元素Hazardous substances and elements
	铅(Pb)	汞(Hg)	镉(Cd)	六价铬(Cr6+)	多溴联苯(PBB)	多溴二苯醚(PBDE)
印制电路配件Printed Circuit Assemblies	X O	O O O	O
外接电(线)缆External cables	X O	O O O	O
内部线路Internal wiring	X O	O O O	O
镜头支架Lens holder	X O	O O O	O
光学镜头Optical lenses	X O	O O O	O
螺帽、螺钉(栓)、螺旋(钉)、垫圈、紧固件Nuts, bolts, screws, washers, fasteners	X O	O O O	O
激光发生器	X O	O O O	O

All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with the "Marking for the restriction of the use of hazardous substances in electrical and electronic product" of Chinese Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the "General guidelines of environment-friendly use period of electronic information products" of Chinese Mainland.

E.3 Taiwan RoHS compliance

限用物質含有情況標示聲明書 (Declaration of the Presence Condition of the Restricted Substances Marking)

設備名稱:投影機,型號(型式):UDMEquipment name:Projector,Type designation:UDM
	限用物質及其化學符號Restricted substances and its chemical symbols
單元Unit	鉛Lead(Pb)	汞Mercury(Hg)	鎘Cadmium(Cd)	六價鉻Hexavalentchromium(Cr6+)	多溴聯苯Polybrominatedbiphenyls(PBB)	多溴二苯醚Polybrominateddiphenylethers(PBDE)
印製電路板配件Printed Circuit Assemblies	—	○○	○○	○
外接電(線)纜External cables	—	○○	○○	○
內部線路
泵Pump	—	○ ○	○ ○	○
備考1. “超出0.1 wt %”及“超出0.01 wt %”係指限用物質之百分比含量超出百分比含量基準值。Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.備考2. “○”係指該項限用物質之百分比含量未超出百分比含量基準值。Note 2: “○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.備考3. “—”係指該項限用物質為排除項目。Note 3: The “—” indicates that the restricted substance corresponds to the exemption.

E.4 Turkey RoHS compliance

Turkey RoHS compliance

[Republic of Turkey: In conformity with the WEEE Regulation]

Regulatory information

Disposal of batteries in the product

This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately from municipal waste.

If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd),

these chemical symbols will appear below the crossed-out wheeled bin symbol.

By participating in separate collection of batteries, you will help to ensure proper disposal and to

prevent potential negative effects on the environment and human health.

E.6 Contact information

Barco contact information

Registered office address: Habomveien 53, N-1630 Gamle Fredrikstad, Norway

Contact address: Beneluxpark 21, 8500 Kortrijk, Belgium

Importers contact information

To find your local importer, contact Barco directly or one of Barco's regional offices via the contact information given on Barco's web site, www.barco.com.

E.7 Production address

Factories

Barco NV (BELGIUM)

President Kennedypark 35, B-8500 Kortrijk

CFG Barco (Beijing) Electronics Co., Ltd.

中影巴可（北京）电子有限公司*

No. 16, Changsheng Road Changping Park, Changping District, 102200, Beijing, P.R.C

A router that serves as an entry point into and exit point out of a network. For example, a local network (LAN) may need a gateway to connect it to a wide area network (WAN) or to the Internet.

DHCP

Dynamic host configuration protocol. DHCP is a communications protocol that lets network administrators manage centrally and automate the assignment of IP addresses in an organization's network. Using the Internet Protocol, each machine that can connect to the Internet needs a unique IP address. When an organization sets up its computer users with a connection to the Internet, an IP address must be assigned to each machine. Without DHCP, the IP address must be entered manually at each computer and, if computers move to another location in another part of the network, a new IP address must be entered. DHCP lets a network administrator supervise and distribute IP addresses from a central point and automatically sends a new IP address when a computer is plugged into a different place in the network.

DMX

DMX-512 Lighting protocol over RS-485 interface. Carries information of 512 channels from a lighting

Glossary

RS232

An Electronic Industries Association (EIA) serial digital interface standard specifying the characteristics of the communication path between two devices using either D-SUB 9 pins or D-SUB 25 pins connectors. This standard is used for relatively short-range communications and does not specify balanced control lines. RS-232 is a serial control standard with a set number of conductors, data rate, word length and type of connector to be used. The standard specifies component connection standards with regard to computer interface. It is also called RS-232-C, which is the third version of the RS-232 standard, and is functionally identical to the CCITT V.24 standard. Logical '0' is > + 3V, Logical '1' is < - 3V. The range between -3V and +3V is the transition zone.

RS422

An EIA serial digital interface standard that specifies the electrical characteristics of balanced (differential) voltage, digital interface circuits. This standard is usable over longer distances than RS-232. This signal governs the asynchronous transmission of computer data at speeds of up to 920,000 bits per second. It is also used as the serial port standard for Macintosh computers. When the difference between the 2 lines is < - 0.2V that equals with a logical '0'. When the difference is > +0.2V that equals to a logical '1'.

Subnet mask

A number that is used to identify a subnetwork so that IP addresses can be shared on a local area network.

Transport latency

The added delay in the image processing chain. The value is the number of lines relative to the output resolution.

List of tools

List of tools

Clean cotton cloth

Clean micro fiber lens cleaning cloth (e.g. Toraysee® cloth(s))

Compressed air

Flat screwdriver 5mm

Lens cleaner (e.g. ZEISS lens cleaner, Purosol™ or other water based lens cleaner products)

Level

List of tools

Index

Numbers/Symbols

3D emitter

setup 113

3D projection 111

3D setup 112

A

Active 3D 111

setup 113

Active Stereo 111

Address

Program

RCU 34

Alignment

Warping 87

4 Corners 91

Bow 93

RGB adjustment 108

RGB gain 108

Brightness 62

C

CE Certification 20

Clean

Exterior 169

Filters 169

Lens 169

Cleaning

Exterior 172

Lens 171

Communication 37

DMX 40

Introduction 38

IR control

Broadcast address 122

Index

Create profile 117

Custom projector name 124

D

Digital Shift 67

Digital Zoom 67

Display

Multiple sources 56

Single source 56

DisplayPort 1.2 inputs

Specifications 180

Disposal 207

Battery 208

DMX 133

DMX chart 193

Basic 194

Extended 195

DMX Chart

Input mapping 194

DMX input 40

DMX interface 40

DMX out 40

Download

Product manual 20

E

Electronic Convergence 151

Enclosed projection 18

Environment conditions 23

Environmental information

Disposal information 207

RoHS compliance

China 205

Taiwan 206

Turkey 207

Ethernet connection 125

Getting started 21

Graphic User Interface

Overview 48

Graphics User Interface 47

GSM

Compliance 199

GSM activation

SIM card 135

GUI

Image 61

Installation 77

Introduction 47

Navigation 5

Overview 48

Test Patterns 53

H

Hazard Distance 16, 18

Modifying optics 19

Hazardous Chemicals 15

HDBaseT inputs

Specifications 179

HDBaseT™ connection

IP address, wired connection 131

HDMI inputs

Specifications 178

High Brightness precautions 16

Host name 124

Index

K

KCC Certification 201

KCC 인증 201

L

Laser Banks

Status 162

Laser radiation 11

Laser range finder 82

Laser ranging 82

LED behavior

Quad Combo Mk I 44

Quad Combo Mk II 43

Quad DP 1.2 45

SFP 46

Lens

Adjustment

Calibration 148

Cleaning 171

Dynamic focus 79

Focus 78

Focus drift compensation 79

Shift 78

Shift to center 80

Tilt sensor 81

Zoom 78

Lens adjustment

Calibration 148

Lens features 143

Lens shift 78

Local keypad

Functionality overview 38

M

Macro

Notice on optical radiation

Optical radiation 10

0

Open source licenses 155

Orientation 85

Projector 22

Overview video timings 184

P

P7

RealColor 71

Passive 3D 111

Passive stereo 111

Power off 28

Power on 24

revent

Damage 14

Electrical shock 11

Fire hazard 13

Personal injury 12

Product safety labels 15

Production address 208

Profile

Delete 119

Profile setup matrix

Profile 116

Profiles

Introduction 116

Preset variables 115

Projector

Components 22

Orientation 22

Projector control

DMX 133

Network

Index

LED behavior 45

R

RCU

Address 34

mini-jack 35

Use 32

XLR 34

Ready mode 28

RealColor

P7 71

Rear projection 18

Registered office 208

Regulatory information 203

Remote access

Camera preview 159

Source preview 158

Remote control

Broadcast address 122

Projector address 122

Reset

3D settings 144

All 144

Blending 144

DMX 144

Features 144

Illumination 144

Image 144

Network settings 144

Optics 144

Orientation 144

Other 144

Projector Profiles 144

Test Patterns 144

User Interface 144

User Interface settings 144

Warping 144

Dinging frame 82

Serial communication 40

Service

Convergence 151

Electronic Convergence 151

Settings

Capture mode 154

Date and time

Automatically 140

Manually 139

General

Open source licenses 155

SFP

Introduction 46

LED behavior 46

SFP inputs

Specifications 181

SIM card

Blocked 136

Single source

Display 56

Software

Update 169

Software update 170

Solarization

Capture mode 154

Remove 154

Source 55

Connect 25

Connector Settings 58

Fiber 46

SFP 46

Single source 56

Small Form-factor Pluggable 46

Specifications 177

DisplayPort 1.2 inputs 180

HDBaseT inputs 179

HDMI inputs 178

SDI inputs 178

SFP inputs 181

Index

IP address, HDBase™ 131

IP address, wired connection 126

IP address, wireless connection 128

ECO mode

Power settings 142

Factory reset 14

Flex brightness 149

Frame 150

Frame Calibration 150

Lens adjustment

Calibration 148

Lens features 143

Maintenance 157

Network 125

Operational mode

Silent mode 153

Power saving settings

ECO mode 142

Standby ECO mode 142

Standby mode 142

Service 157

Units

Distance 138

Temperature 138

X

XLR

RCU 34

XLR connector

Control 135

Z

Zoom 78

T

Test Patterns 53

Themes 137

Tilt sensor

Calibration 163

Touch panel 39

Turkey RoHS 207

U

UK Compliance 20. 204

Units 138

Index