CFC-68 - Audio accessory Auray - Free user manual and instructions

USER MANUAL CFC-68 Auray

Cable Replacement Kit

for CFP Series Carbon Fiber Boom Poles

Owner's Manual

TA3 (mini XLR) connector Coiled XLR cable Right-angle XLR connector Nylon line 1.5 mm hex key Tip strain relief Introduction

Instructions

Replacing the Cable - Boom Pole with Bottom Exit XLR

Remove the old cable

1. Use the hex key to loosen the set screw on the tip. 1
2. Remove the tip by unscrewing it. 2
3. Lift the cable and strain relief out of the lip exit slot. 3

Tip: Before proceeding, push a small length of cable into the tube from the tip of the pole. This will give you enough slack to complete the following steps.

1. Unscrew the bottom housing from the base of the boom pole.4
2. Unscrew the plastic TA3 strain relief 5
3. Disconnect the TA3 connector by pressing on the locking tab and gently removing the connector from the mount.

Note: The TA3 connector should easily disconnect. Do not force or pull on the cable to disconnect it. Doing so could damage the housing or the connector.

Install the replacement cable

1 Holding the boom pole upright, insert the replacement cable into the top of the boom pole, and snake it through the tubing until the TA3 connector is exposed at the bottom of the pole.

Note: If the cable does not move smoothly through the tubing, use the included nylon line tie the line to the TA3 connector and drop it through the tubing from the top 3. Pull the string from the bottom of the boom pole to snake the cable through the tubing. Make sure to remove the line before continuing.

1. Fit the narrow side of the strain relief over the TA3 connector, and push it past the TA3 connector's locking tab.

2. Plug the TA3 connector to the bottom housing by inserting it into the TA3 mount and

Replacing the Cable - Boom Pole with Side Exit XLR

Remove the old cable

1. Use the hex key to loosen the set screw on the tip.
2. Remove the tip by unscrewing it.
3. Lift the cable and strain relief out of the tip exit slot. 3

Tip: Before proceeding, push a small length of cable into the tube from the tip of the pole. This will give you enough slack to complete the following steps.

1. Unscrew the side exit housing, 4 and move the plastic strain relief cap so that the TA3 connector inside the housing is exposed.
   5 Disconnect the TA3 connector by pressing on the locking tab and gently remove the connector from the mount.5

Note: The TA3 connector should easily disconnect. Do not force or pull on the cable to disconnect it. Doing so could damage the housing or the

Install the replacement cable

1. Holding the boom pole upright, insert the replacement cable into the top of the boom pole, and snake it through the tubing until the TA3 connector is exposed at the bottom of the pole.

Note: If the cable does not move smoothly through the tubing, use the included nylon line. Tie the string to the TA3 connector, 3 and drop it through the tubing from the top. Pull the line from the bottom of the boom pole to snake the cable through the tubing. Make sure to remove the line before continuing.

1. I'it the narrow side of the strain relief over the TA3 connector, and push it past the TA3 connector's locking tab. 4

2. Plug the TA3 connector into the side-exit XLR housing by inserting it into the TA3 mount and pushing in until

Warnings

• Please read and follow these instructions, and keep this manual in a safe place.
• Handle the product with care.
  • Use only parts provided by the manufacturer.
  • Make sure the item is intact and that there are no missing parts.
• Do not attempt to disassemble or repair the equipment—doing so will void the warranty, and Auray will not be responsible for any damage.
  • All photos are for illustrative purposes.

One-Year Limited Warranty

This Aurya product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later. The warranty provider's responsibility with respect to this limited warranty shall be limited solely to repair or replacement, at the provider's discretion, of any product that fails during normal use of this product in its intended manner and in its intended environment. Imperability of the product or part(s) shall be determined by the warranty provider. If the product has been discontinued, the warranty provider reserves the right to replace it with a model of equivalent quality and function.

This warranty does not cover damage or defect caused by misuse, neglect, accident, alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPECTS WARRANTIES AND ANY IMPROVED