B20SHA - Camera BZBGear - Free user manual and instructions

USER MANUAL B20SHA BZBGear

HD Integrated Camera

User Manual

Exterior view of a modern office building (no signage)

Contents

1. Precautions....2
2. Functions .... 3
   2.1 Technical Parameters....3
   2.2 Camera Parameters .... 3
   2.3 Technical Specification 4
   3.1 Camera Interface Instruction....5
   3.2 Camera Dimensions ....5
3. Camera Menu Settings....6
   4.1 Exposure 6
   4.2 Color 7
   4.3 Picture 7
   4.4 P/T/Z 8
   4.5 Noise Reduction....8
   4.6 Video Format....8
   4.7 System 9

1. Precautions

Electronic

- The electrical safety standards of the country and region must be strictly observed in the installation and use of this product.

There is no power switch in the body of this product. If there is an equipment failure immediately disconnect the power supply. The video cable and control cable should be shielded and wired independently and cannot be mixed with other cables.

- Transportation

During transportation, storage, and installation it is necessary to prevent damage caused by heavy pressure, severe vibration, immersion, etc.

- Installation

Please refer to the user installation manual carefully during installation. Handle the camera components gently to avoid damage to the camera. The camera lens is an advanced optical product - protect the lens from contact to avoid scratching and affecting image quality..

● Maintenance

All installation and maintenance work on this unit should be performed by a qualified service technician or system installer.

- Disassembly

Do not disassemble the camera or protective cover. There are no user-serviceable parts in the product. It should be repaired by professional maintenance personnel.

2. Functions

2.1 Technical Parameters

Electronics		Communication
Constant Voltage	DC12V	Baud rate	4800/9600/19200/38400bps
Power Consumption	12W	Protocol	VISCA /Pelco - D/Pelco - P/ONVIF
Encoding	Built-in	ID	1~255
Operation Environment	-10°~+50°
Humidity	0~95%
Installation	Desk, Top-down
Presets	255	N.W	1.2kg

2.2 Camera Parameters

Spec\Model	20X
Senser	1/2.8" Progressive CMOS
Effect Pixel	2.3 Megapixel
Zoom	20X Optical Zoom, 13X Digital Zoom

20X Optical Zoom 12X Digital Zoom

2.3 Technical Specification

Input/Output Interface

● Video Output: 3G-SDI / HDMI / IP Streaming
● Audio Input: 3.5mm Audio Input
● Input/Output Control Interface: 2PIN Terminal, 3.50mm
● Power Interface: 2PIN Terminal, 3.50mm or POE+

Features

● Supports RS232C or RS485 protocols, allowing a PTZ Controller or PC to control the camera.
● Improved image quality from the newly developed digital signal processor (DSP).
Built-in attenuation filter that physically removes IR (infrared). This filter can be turned on or off automatically, providing high quality images for shooting environments of different brightness.
- The five-direction button on the back of the camera allows users to quickly and easily change any parameters of the camera.
● Default IP Address: 192.168.1.162
● Built-in Audio Input. Audio encode standard support G.711.G.722.G.722.1.

3.1 Camera Interface instruction

1 2 3 4 5 6 7 A B + RS45E 12V A-1N HDMI 3G SBT FAR MIDE NEAR TELE LAN

1. Lens

2. Terminal Pin Interface

A: RS485+

B: RS485

-/+: DC12V Power Interface

1. Five-direction Button

2. Audio-IN

3. HDMI

6.3G-SDI

1. LAN

3.2 Dimensions (mm)

4. Camera Menu Settings

1. Press and hold the center button for 3 seconds to enter the Main Menu
2. Use the directional keys to navigate the menu and settings.

4.1 EXPOSURE

• Enter the main menu and navigate to【EXPOSURE】. Press right to enter the sub-menu.
  【AE MODE】

Options: AUTO/SHUTTER/IRIS/BRIGHT

modified depending on the selected mode. The

range of settings are as follows:

Shutter: 1/1-1/10000

MAIN MENU

EXPOSURE

COLOR

PICTURE

ADVANCED

PRIVACY

SYSTEM

EXIT

EXPOSURE

AE MODE: AUTO

AE LEVEL: N/A

EXCOMP: OFF

BACKLIGHT: OFF

HLC: 8

FLICKER: OFF

GAMMA: 6

BACK

4.2 COLOR

Enter Main Menu, navigate to 【COLOR】, press right to enter sub-menu.

【WB MODE】

Options: AUTO, INDOOR, OUTDOOR, ATW, OPW, MANUAL

【R GAIN/B GAIN】

COLOR

WB MODE:	AUTO
R GAIN:	N/A
B GAIN:	N/A
COLOR GAIN	100
COLOR HUE	0
BACK
EXIT

When the WB MODE is set to MANUAL the R Gain\B Gain values can be independently adjusted.

● 【COLOR GAIN】 Setting Valued range: 60 - 200
● 【COLOR HUE】 Setting Valued range: -14 - 14

4.3 PICTURE

Enter Main Menu, navigate to 【PICTURE】, press Right Button to enter sub-menu.

Status Network status Shared Public Network You are connected to the Internet. You can't have been done, but you can help me prevent a network connection or change your properties. Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings Change your network settings

• Right-click on your connection (Wi-Fi or Ethernet) and select "Properties".
- Select "Internet protocol version 4 (TCP/IPv4)" as shown below and click "Properties".

Stream/Preview Stream Stream Data Stream Data (File List)... Stream Data (File List)... Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (File List) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Data) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial) Stream Data (Dial)

• For the following steps refer to the diagram below. Click on the bubble for "Use the following IP address"
• In the IP address field enter a non-conflicting IP address on the same subnet as the camera. If there is another device with the same IP address you will not be able to connect. In the example below we are using 192.168.1.200

- On the left side of your screen select Network. In the IP address field, you will enter the unused IP address you selected at the beginning. Our example will use an address of 192.168.20.186.

*This address MUST NOT be in use by any other device on your network or you will create an IP conflict and be unable to access your camera. *

• In the Subnet Mask field enter 255.255.255.0 the enter the IP address of your Default Gateway in the field
• Unless you are given different information by your network administrator you should enter 8.8.8.8 for DNS1 and 8.8.4.4 for DNS2. Click Save.

Network Login IP Address: IP地址: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址 IP Address: IP地址

- Once you complete the camera setup, repeat the steps on your computer to adjust "Internet Protocol Version 4 (TCP/IPV4) Properties" and click the bubbles for "Obtain IP address automatically" and "Obtain DNS server address automatically". Click OK to close all network-related screens.

Preset Tab: Use the Preset tabs to Set, Recall, and Delete Preset positions. To record a preset, adjust the camera to the desired location and zoom level. Highlight the preset number you wish to record and click the "Set" button. To recall a preset, highlight the preset number you wish to recall and click the "Call" button. To delete a preset, highlight the preset number you with to recall and click "Delete".

Configuration Screen

From the configuration screen you can set and adjust all the functions and parameters of the camera.

System Page

The system page contains information regarding the camera, time settings, firmware, and main video output resolution.

Version Tab: The version tab contains camera information including model number, serial number, firmware and hardware versions, and MAC address.

Time Tab: The time tab allows you to adjust time, date, and time zone settings.

Maintain Tab: This tab allows you to reboot, restore factory default settings, and update the firmware.

Config Tab: Name the camera, select menu language, select Video Standard (not used), set output resolution, and enable/disable UVC (USB) video output.

Network Page

The network page includes network settings, port settings, and streaming settings.

ETH Tab: Select static (Config IP Address) or DHCP (Auto IP Address), select Auto or Manual DNS settings.

Service Tab

MSG Port: default 8080

RTSP Port: default 554

HTTP Port: default 80

VISCA Port: default 52381

WebSocket Port: default 8880

Note: Changing the port number requires restarting the camera to valid. In order to avoid port conflicts, please be careful to modify.

end of your camera's IP address as shown below:

Default Main Stream: rtsp://192.168.1.162:554/0/0/0 Default Sub-Stream:

rtsp://192.168.1.162:554/0/0/1

Frame Rate: Specify frame rate (1-30). Frame Rate Priority prioritizes frame rate over image quality when

VBR mode is enabled.

GOP: Frame interval (1-60). Default is 30.

Bitrate: Video Bit Rate (1-10240). Default is 4096

Resolution: Set streaming video resolution

Stream Mix Type: Select Complex or Video Stream. Complex Stream includes audio.

Encode Type: Select video encoding format.

Bitrate Type: CBR (Coded Bit Rate), VBR (Variable Bit Rate), Fix QP (Fixed Bit Rate).

-When CBR is selected stream quality, IFrame, and PFrame settings are unavailable.

-When VBR is selected IFrame and PFrame settings are unavailable.

-When Fix QP is selected stream quality setting is unavailable.

Audio Encode Type: Select audio encoding format. AAC is recommended for most streaming platforms.

Audio Input Mode: Select Mic Level or Line Level

Audio Input Gain: Set the audio input gain level (1-10, mute)

Audio Quality: Select High or Low

Image Page

On the image page you will find all the image, iris, and focus settings for adjusting the camera's picture.

Display Tab-

Brightness: Brightness adjustment slider

Sensitivity: Auto focus sensitivity level

ICR Mode: Infrared Cutfilter Removal Mode

AE Mode: Auto Exposure Mode

AE Level: Auto Exposure Level adjustment

HLC: Highlight Compensation Level

DNR(2D): 2D Digital Noise Reduction adjustment

Gamma: Gamma adjustment

Safety Page

From this screen you can modify the login information

PTZ Page

From this screen you can view and modify the PTZ control settings of the camera.

PTZ Address: Set the PTZ control address of the camera

Protocol: Set the serial control protocol

Baud Rate: Set the serial control baud rate

LR-Direction: Reverse the left and right controls

Vertical Axis: Reverse the up and down controls

Display Mag: Display current magnification (zoom) level

Status Page

On this screen you can view the current bit rates of the 3 IP streams.

7. Warranty

BZBGEAR Pro AV products and Cameras come with a three-year warranty. An extended two-year warranty is available for our Cameras upon registration for a total of five years.

For an extended two-year warranty on our Cameras, follow these steps:

1. Register your Camera within 90 days of purchase by visiting bzbgear.com/warranty.
2. Complete the registration form. Provide all necessary proof of purchase details, including serial number and a copy of your sales receipt.

For complete warranty information, please visit bzbgear.com/warranty or scan the QR code below.

8. Mission Statement

BZBGEAR manifests from the competitive nature of the audiovisual and live streaming industry to innovate while keeping the customer in mind. AV solutions can cost a pretty penny, and new technology only adds to it. We believe everyone deserves to see, hear, and feel the advancements made in today's AV world without having to break the bank. BZBGEAR is your answer for applications requiring the latest pre-AV and live streaming solutions.