CDT2120PZ - Security Camera Costar - Free user manual and instructions

USER MANUAL CDT2120PZ Costar

Close-up of a white security camera with a circular lens and dome, no visible text or symbols.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.

CAUTION

Warning symbol image showing a lightning bolt inside a triangle with a downward arrow

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

Warning symbol image with exclamation mark inside a triangle

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

Warning sign depicting a lightning bolt symbol inside a triangle

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

Warning symbol image with exclamation mark inside triangle

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC INFORMATION: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This Class A digital apparatus complies with Canadian ICES-003.

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

Symbolic icon of a person climbing a ladder inside a circle with no text or symbols

1. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

2. CAUTION - THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.

3. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

Table of Contents

Chapter 1 — Introduction ...... 6

1.1 Features ....6

Chapter 2 — Installation and Configuration .... 7

2.1 Package Contents ....7
2.2 Installation....8

2.2.1 Locking Dome Camera....8
2.2.2 Heater Kit Installation (Optional)....10

2.3 Basic Configuration of Dome Camera System....11

2.4 Setting Dome Camera Address (ID)....12
2.5 Setting Dome Camera Video Type & Coaxitron Protocol ....12
2.6 Connections....13
2.7 Getting Started....14

Chapter 3 — Program and Operation....15

3.1 Dome Camera Selection ....15
3.2 Accessing the On-Screen Menu Utility....15
3.3 How to control the On-Screen Menu Utility ....15
3.4 Auto Scan (Shortcut: SCAN)....16
3.5 Preset (Shortcut: PRST)....18
3.6 Shortcut of Preset Program ....20
3.7 Tour (Shortcut: TOUR)....20
3.8 Pattern (Shortcut: PTRN)....22
3.9 Privacy Zone....23
3.10 Camera Menu....24
3.11 Dome Communication ....27
3.12 Alarm ....28
3.13 Dome Setup ....29

Appendix A — Specifications .... 36

Appendix B — Troubleshooting .... 38

Chapter 1 — Introduction

1.1 Features

The dome camera and the keyboard controller make up the building blocks for any surveillance/security system. Using multiple keyboard controllers and multiple dome cameras, no place is too large for monitoring. Extensible and flexible architecture facilitates remote control functions for a variety of external switching devices such as multiplexers and DVRs.

• Built-in optical power zoom camera with True Night Shot function
• 240 Preset positions with the individual camera AE setup
- 8 Tours consist of Presets, Patterns, Auto Scans and other Tours can be programmed with over 300 functions and preset locations. While moving, each Preset scan can be watched in smooth Vector Scan mode.
- 16 Auto Scans with the normal, the vector, and the random mode and the endless Auto-Pan with 13 speed steps
- 8 Patterns (up to 500 seconds) and 8 Privacy Zones
• 4 Alarm inputs, 2 Alarm outputs (5VTTL)
- Variable speed from 0.1^ / sec . to 380^ / sec .

Three Variable speed (SLOW, NORMAL, TURBO)

Turbo speed is 380^/sec . with Ctrl key pressed.

• Pan/Tilt speed is inversely proportional to the zoom ratio with the option.
  • Maximum speed is 380^/sec . when Preset command.
  • Auto Calibration from 0.1° to 6° (Tilt range is -10° to 190°)
• Programmable user preferences (alarm, preset, title, etc.)
• 180° Digital Flip
• Up to 3999 selectable camera addresses
• Function Run menu using DVR without function key (Pattern, Scan ...)
  • Built-in RS-485 receiver driver
  • 12VDC or 24VAC for Dome
• Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

Chapter 2 — Installation and Configuration

2.1 Package Contents

The dome camera is designed with compact, small size, hard dome camera housing.

The housing is constructed of aluminum, steel and plastic. The housing is designed to be mounted on a wall or a ceiling. The housing meets the Protection Classification IP66 standards for dust and moisture resistance.

*	D	o	m	e	C	a	m	e	r
*	Instruction Manual (This Document)				1
*	T	e	m	p	l	a	t	e	S
*	Mounting	Bracket
*	S	a	f	e	t	y	L	a	n
*	Accessory	Kit
	1) Mounting screws (PH6 x 35.0)				(4)
	2) Plastic anchors
	3) O - R i n g						s
	4) Torx wrench
*	Accessory	Connector
	1) 2-Pin	Terminal	Block
	2) 3-Pin	Terminal	Block
	3) 4-Pin	Terminal	Block
	4) 5-Pin	Terminal	Block

2.2 Installation

The dome camera is for use in surface or pendent mounting applications, and the mounting member must be capable of supporting loads of up to 10 lb (4.5 kg). (Pendent mounting must use pendent mount accessory.)

The dome camera's mounting bracket should be attached to a structural object, such as hard wood, wall stud or ceiling rafter that supports the weight of the dome camera.

Plastic Anchors (4x) Mounting Bracket (1x) Mounting Screws (4x) Safety Lanyard (1x) Dome Camera (1x)

CAUTION: A silicone rubber sealant must be applied to seal the housing to secure waterproofing.

2.2.1 Locking Dome Camera

1. Make screw holes on the ceiling using the supplied mounting Template Sheet (Figure A).
2. Fix the Mounting Bracket to the ceiling using supplied Anchors (4x) and Mounting Screws (4x) (Figure B).
3. Hook up the Safety Lanyard to the Safety Lanyard Hook of the Mounting Bracket (Figure C).
4. Align the locking tab on the bracket and the locking slot on the base of the dome (Figure D).
5. Turn the dome to the counterclockwise about 10 degree to the locked position (Figure E).

CAUTION: Before installing mounting bracket to surface pre-adjust the four mounting screws "A" on the base of the dome camera to best match the mounting bracket locked position. Unscrew the locking screw on the side of the dome's base and fit the tab of the mounting bracket into the locking slot. Screws "A" should not be too tight or too loose when the dome is in the locked position. After setting the proper positions of screws "A" remove the mounting bracket and install it to the proper surface. If it is too difficult to lock the dome in position after the mounting bracket has been installed readjust the screws "A" by unscrewing them a small amount and try to install dome camera again.

2.2.2 Heater Kit Installation (Optional)

1. Assemble the Heater board to two bossed with screws.

Take a reference "B" in the bottom case as below.

1. Place the Heater in the slot "A".

Heater cable should be placed away from the Main Board.

1. Plug the power connector to the socket "C" (J1) of the Heater Board.

2. 24VAC is recommended to use for the camera power for stable operation with heater kit.

C B A HEATER KIT VIEW Heater Board

• HEATER (IF APPLICABLE)

Power Supply 24VAC
Power Consumption 10W
Heater ON at 59°F (15°C)
Heater OFF at 77°F (25°C)

- POWER

Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

CAUTION: Please reset the camera after 30 minutes when installing it in situations colder than -10°C.

2.3 Basic Configuration of Dome Camera System

Diagram showing a cable connector with six labeled connectors, illustrating the connection structure.

No.	Connector	Wire Color	Description
1 3-pin terminal block		RED 24VAC or WHITE 24VAC or GREEN RS-485+	12VDC+
			12VDC-
2 2-pin terminal block
3 5-pin terminal block		GRAY ALARM INPUT 1
		VIOLET ALARM INPUT 2
		ORANGE ALARM INPUT 3
		SKY BLUE ALARM INPUT 4
		BLACK GND
4 4-pin terminal block		YELLOW ALARM OUTPUT 1
		BLACK & WHITE GND
		SKY BLUE & BALCK ALARM OUTPUT 2
		ORANGE & BLACK GND
5	BNC jack	BLUE	HD-TVI/AHD OUTPUT
6	BNC jack	BLACK	CVBS OUTPUT

The dome camera must be installed by qualified service personnel in accordance with all local and federal electrical and building codes.

Dip Switch

NOTE: Open the DIP switch cover and change the setting of DIP switch. The cover should be closed after setting DIP switch.

2.4 Setting Dome Camera Address (ID)

To prevent damage, each dome camera must have a unique address (ID). The factory default setting is 1.

Refer to '3.11 Dome Communication' section for detailed information.

2.5 Setting Dome Camera Video Type & Coaxitron Protocol

S1

You can set video type with D1 in S1.

S1-D1 Video Type

OFF HD-TVI OUTPUT

ON AHD OUTPUT

You can set coaxitron protocol with D2 and D3 in S1.

S1-D2 S1-D3 HD-TVI OUTPUT AHD OUTPUT
OFF OFF Hikvision-C Hitron-C
ON OFF Pelco-C Reserved
OFF ON Reserved Reserved
ON	ON Reserved Reserved

2.6 Connections

- Connecting to the RS-485

The dome camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS-485 half-duplex serial communications signals.

- Connecting HD-TVI/AHD Output connector

Connect the HD-TVI/AHD output (BNC) connector to the monitor or video input.

- Connecting CVBS Output connector

Connect the CVBS output (BNC) connector to the monitor or video input.

- Connecting Alarms

- A1,A2,A3,A4 (Alarm Input 1,2,3,4)

You can use external devices to signal the dome camera to react on events. Mechanical or electrical switches can be wired to the A1,A2,A3,A4 (Alarm Input 1,2,3,4) and G (Ground) connectors.

See Chapter 3 — Program and Operation for configuring alarm input.

- G (Ground)

NOTE: All the connectors marked G or GND are common.

Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.

- AO1,AO2 (5VTTL Alarm Output 1,2)

The dome camera can activate external devices such as buzzers or lights. Connect the device to the AO1,AO2 (Alarm Output 1,2) and G (Ground) connectors.

See Chapter 3 — Program and Operation for configuring alarm output.

- Connecting the Power

Connect power of 12VDC or 24VAC for the dome camera.

When using a 12VDC adapter, connect the positive (+) pole to the ‘+’ position and the negative (-) pole to the ‘-’ position.

Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

2.7 Getting Started

Once installed apply power to the dome camera. The dome camera will start a configuration sequence.

graph LR
    A["FUNCTION TITLE"] --> B["001"]
    C["INFORMATION DISPLAY"] --> D["EMPTY DATA"]
    E["ALARM DISPLAY"] --> F["ALARM:1"]
    G["STATUS OF FOCUS and AE"] --> H["AF AE"]
    I["CAMERA TITLE & ID PAN & TILT ANGLE"] --> J["DOMEID:0001 360.0 090.0"]

OSD Position

Chapter 3 — Program and Operation

3.1 Dome Camera Selection

Before you program or operate a dome camera, you must select the dome camera by pressing No. + CAM keys.

Example: Pressing 1, 0 + CAM keys sequentially will select dome camera 10. The selected dome camera ID will be displayed on the LCD monitor of the keyboard controller.

3.2 Accessing the On-Screen Menu Utility

You can call up the On-screen menu utility on your monitor by pressing the MENU key on the keyboard controller, the following On-screen menu utility will appear:

DOME MENU

AUTO SCAN

PRESET

TOUR

PATTERN

PRIVACY ZONE

CAMERA

DOME COMMUNICATION

ALARM

DOME SETUP

EXIT (ESC TO EXIT)

3.3 How to control the On-Screen Menu Utility

Function Button
Call the On-screen menu utility.	MENU
Navigate through the menu items.	Joystick up or down
Go into the sub-menu items.	Joystick left or right or IRIS Open
Change value.Enter the editing title mode.	Joystick left or right or Zoom handle twist or Tele, Wide
Change value of angle.	CTRL + Joystick
Enter the changing angle mode.	IRIS Open
Exit the changing angle mode.	IRIS Close
Escape (EXIT)	ESC

3.4 Auto Scan (Shortcut: SCAN)

The Auto Scan supports up to 17 programmed angles at user-programmable speeds.

Follow these steps to program Auto Scan:

AUTO SCAN SETUP

NUMBER : 01
TITLE : A01
MODE : NORMAL
SPEED : 5 STEP
START ANGLE : ----
END ANGLE : ----
SCAN DIR : CCW
SWAP : OFF
DWELL : 03 SEC
SAVE AND EXIT(ESC TO CANCEL) 

NUMBER 01 \~ 08, 10 \~ 17, 09: AUTO-PAN mode.

TITLE up to 6 characters

MODE NORMAL, VECTOR, RANDOM (AUTO-PAN mode: NORMAL, RANDOM only).

NORMAL Move from start point to end point in panning only

VECTOR Move from start point to end point including tilt and zoom simultaneously and linearly.

RANDOM Move randomly between the start point and the end point

SPEED 1 \~ 13 step, the lower number means the slower speed.

SCAN DIR Set the Scan direction, CCW (Counter Clock Wise), CW (Clock Wise).

SWAP Swaps the start point for the end point.

DWELL Set the dwell time at the both end, 01 \~ 99 seconds.

1. Press the SCAN key to enter the Auto Scan menu directly. Or press the MENU key to display the main menu on the monitor. Scroll to Auto Scan and push the Joystick to the right.
2. Select "NUMBER" and set the desired number by pushing the Joystick to the left or right.
3. Select "TITLE" and twist the Joystick to enter the title edit mode.
4. Twist the Joystick to change the alphanumeric characters and move the next position by pushing the Joystick to the left or right. Or move down to the character table and press the CTRL or IRIS Open key at the desired character then the cursor position moves to the next position automatically. Push the Joystick to the left or right at the "ALL DELETE" field to delete all characters. Push the Joystick to the left or right at the "EXIT" field to finish title edit menu.

TITLE EDIT MENU
(CTRL KEY)

A01
*
A B C D E F G H I J
K L M N O P Q R S T
U V W X Y Z 0 1 2 3
4 5 6 7 8 9 ( )
ALL DELETE
EXIT(ESC TO EXIT) 

1. Select "MODE" and "SPEED".

2. Select "START ANGLE". Hold down the CTRL key while selecting the start position using the Joystick. Current panning position will be displayed. Release the CTRL key to complete the selection of the start position. Or press the IRIS Open key then the "CONTROL" displays. Move the desired position and the zoom position. Press the IRIS Close key then the "CONTROL" disappears. To adjust at the 0.1 degree interval, twist the Joystick at the pan field and the tilt field.

3. Select "END ANGLE". Hold down the CTRL key while moving the Joystick to select the end position. The end position angle should be larger than start position. Release the CTRL key to complete the selection of the end position. Or press the IRIS Open key then the "CONTROL" displays. Move the desired position and the zoom position. Press the IRIS Close key then the "CONTROL" disappears. To adjust at the 0.1 degree interval, twist the Joystick at the pan field and the tilt field.

4. Set "SCAN DIR" to CCW or CW.

5. Select "SWAP", Set to ON to exchange the start angle and the end angle.

6. Set "DWELL time".

7. Select "SAVE AND EXIT" and push the Joystick to the right or press the IRIS Open key. Press the ESC or IRIS Close key to exit the program without saving.

NOTE: Pressing the HOME key delete stored data at the angle field.

To set the position using the Preset position:

a. Before entering the Auto Scan menu, select a Preset position as a starting point for Auto Scan.

Example: 2 + PRST keys and do step 1 to 5. In step 6, just press the CTRL key at the start angle position, the current position will be displayed as a start position.

b. Save and Exit from the menu.

c. In normal mode, call a Preset to be the end point of Scan. Press 3 + PRST keys then press the SCAN key to enter the Auto Scan menu. Move the cursor position to END ANGLE. Just press the CTRL key at the end angle position. Save and exit from the menu.

Press the SCAN key on the angle field to display with the small OSD. Then the screen will show as below.

AUTO SCAN AREA SETUP (CTRL KEY) NUMBER 01 START : ---- ---- END : ---- ---- EXIT(ESC TO EXIT)

The setting procedure is the same as above.

NOTE: 09: AUTO-PAN mode (endless panning)

3.5 Preset (Shortcut: PRST)

If you need to view specific places routinely, you should program Presets. A Preset is a programmed video scene with automatic pan, tilt, zoom, focus, and AE settings. Once programmed, placing the number position and pressing the PRST key on your controller calls up that Preset automatically. In addition, Presets may be assigned the "home" position for the dome camera. As many as 240 Presets, whose positions are saved in the dome's firmware, may be programmed.

There are eight pages of Preset menu. Each page has 30 Presets. Pages can be scrolled by pushing the Joystick to the left or right on the first or last No. of Preset.

PRESET SETUP NUMBER : 001 TITLE : ---- CAMERA SET DWELL : -- SEC 1 2 3 4 5 6 7 8 9 0 - * - - - - - - - - - - - - - - - - - - - - - - - - - - - - NEXT PAGE SAVE AND EXIT (ESC TO CANCEL)

• Blank Preset position
  * Position has the Preset
  ! Current cursor position

Follow steps below to store the Preset positions:

1. Press the PRST key to enter the Preset menu directly. Or press the MENU key to display the main menu on the monitor. Scroll to Preset and push the Joystick to the right.
2. Select the blank Preset position to be stored by pushing the Joystick up, down, right, or left.
3. After selecting a blank position, press and hold the CTRL key. Use the Joystick to control the direction of the camera and lens.
4. After aiming the camera (view direction and lens control), release the CTRL key. The cursor will be on the "TITLE" after saving data then twist the Joystick or press the Tele or Wide key to edit the Preset title. Follow the procedure of the Auto Scan above to edit titles.
5. Select "CAMERA SET" and push the Joystick to the left or right. Then the Preset camera setup displays.

PRESET CAMERA SETUP
FOCUS : AUTO
MOTION: OFF
MOTION SETUP
AE SETUP
SAVE AND EXIT(ESC TO CANCEL)

Set FOCUS AUTO, MANUAL, ONE PUSH

Set MOTION OFF, ON

Select "MOTION SETUP" and push the Joystick to the left or right. Then the MOTION setup displays.

MOTION SETUP

SENSITIVITY: 10
RESOLUTION : 02
POSITION : ALL
DELAY : 00 SEC
OUTPUT : OFF
HOLD TIME : 03 SEC
EXIT(ESC TO EXIT) 

Set SENSITIVITY 00 \~ 20

Set RESOLUTION 01 \~ 04

Set POSITION ALL, CENTER

Set DELAY 00 \~ 05 seconds

Set OUTPUT OFF, OUT1, OUT2

Set HOLD TIME 03 \~ 99 seconds

Select "AE SETUP" and push the Joystick to the left or right. Then the AE setup displays. Refer to the AE SETUP in the camera setup.

1. Set "DWELL time". (03 \~ 99 seconds)
2. To select the next page of Presets, scroll the page by pushing the Joystick to the left or right on the first or last columns of the menu.
3. Repeat step 2 through 7 for each additional Preset position.
4. Select "SAVE AND EXIT" and push the Joystick to the right or press the IRIS Open key. Press the ESC or IRIS Close key to exit the program without saving.

NOTE: Press the HOME key at programmed Preset position (*) to delete a programmed Preset view.

The position, which is marked with the *, already has the Preset view assigned. Press the PRST key on the * to review the stored Preset. The camera will show the stored Preset scene.

PRESET AREA SETUP

(CTRL KEY) 

NUMBER 001

PAN TILT

000.0 000.0

EXIT (ESC TO EXIT)

Hold down the CTRL key while selecting the desired scene using the Joystick. Current position will be displayed. Release the CTRL key to complete. Or press the IRIS Open key then the "CONTROL" displays. Move the desired position and the zoom position. Press the IRIS Close key then the "CONTROL" disappears. Select "EXIT" and push the Joystick to the right.

3.6 Shortcut of Preset Program

After selecting the desired scene, press No. (1 to 240), and press the CTRL and PRST keys subsequently. The current view will be stored to the selected Preset number if the Preset number is empty. If selected Preset number is not empty, "OVER WRITE" message will be displayed on the monitor and select the "OK" and push the Joystick to the right to overwrite.

Example: 1, 0, 1 + CTRL + PRST keys will store current view as Preset no. 101. In this case, focus will be programmed as Auto, dwell time will be set to 3 second, and the current AE mode will be programmed.

3.7 Tour (Shortcut: TOUR)

There are 8 programmable Tours. Each Tour consists of up to 42 Preset positions, Patterns, Scans or other Tours (second-level). Using second-level Tours, it can be expanded to over 300 functions in a single Tour.

TOUR SETUP
NUMBER : 01
TITLE : T01
SCAN TYPE : NORMAL
SPEED : -- STEP
TOUR FUNC
SAVE AND EXIT(ESC TO CANCEL) 

TOUR FUNC SETUP
(CTRL KEY)
DWELL : -- SEC
003 A04 --- --- ---
--- --- --- --- ---
--- --- P01 --- ---
--- T02 --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
--- --- --- --- ---
EXIT (ESC TO EXIT) 

--- Blank position
SCAN TYPE NORMAL, VECTOR
DWELL 03 ~ 99 seconds
003 Preset (1 ~ 240)
A04 Auto Scan (1 ~ 8, 10 ~ 17)
P01 Pattern (1 ~ 8)
T02 Tour (1 ~ 8) 

Follow the steps below to program the Tours:

1. Press the MENU key to display the main menu on the monitor. Scroll to Tour and push the Joystick to the right to enter the Tour menu. Or just press the TOUR key on the keyboard.
2. Select "NUMBER" and set the desired number by pushing the Joystick to the left or right.

3. Choose a blank position to be programmed by pushing the Joystick up, down, right, or left.

4. To add a stored Preset, twist the Joystick then the stored Preset number displays.

5. To place functions other than Preset, press the TOUR, PTRN or SCAN keys for Tour, Pattern or Auto Scan respectively.
6. You can also overwrite the programmed number and remove a stored number from the Tour, press the HOME key on the stored number, a blank position mark (---) will be displayed.
7. Repeat step 2 through 6 for each desired position. Each title will be displayed on top of the line.
8. To edit the "TITLE", follow the procedure of the Auto Scan above to edit titles.
9. Select "SAVE AND EXIT" and push the Joystick to the right or press the IRIS Open key. Press the ESC or IRIS Close key to exit the program without saving.

You can expand the Tour sequence by calling other programmed Tours.

NOTE: The speed applies in the vector mode only.

NOTE: In the Tour mode, in conjunction with Preset and Auto Scan, you can make the camera travel from a Preset position to another Preset position at a specific speed.

Example: Preset 001>002>003>004>005>006, Auto Scan 01 starts at Preset 002, ends at Preset 003, Auto Scan 02 starts at Preset 005, ends at Preset 006; Tour 001, 002, A01, 004, A02.

1 → 2 2\~3 → 4 → 5\~6, repeat where → : Quick move, \~ : Programmed speed

To change the dwell time of the Preset in the Tour:

Use the Joystick to move the cursor to a stored Preset position.

By pressing the PRST key, the camera will move to the stored Preset view and the cursor moves to the dwell time field.

After changing the dwell time, press the PRST key and the cursor moves to the Preset number.

To assign the functions other than Preset in the Tour when the function key is not existed:

Use the Joystick to move the cursor to a stored Preset position.

Pressing the CTRL or IRIS Open key will change the Preset number to other function (Auto Scan, Pattern, Tour or Preset) with the first programmed number.

To change the number, twist the Joystick or press the Tele or Wide key.

3.8 Pattern (Shortcut: PTRN)

The Pattern feature records user control of the selected dome camera. Up to 8 Patterns can be stored and played back by pressing No. + PTRN keys subsequently.

PATTERN SETUP (CTRL KEY)
NO	TITLE	SEC	PERCENT
1 :	P01	000	00.0%
2 :	P02	000	00.0%
3 :	P03	000	00.0%
4 :	P04	000	00.0%
5 :	P05	000	00.0%
6 :	P06	000	00.0%
7 :	P07	000	00.0%
8 :	P08	000	00.0%
SAVE AND EXIT (ESC TO CANCEL)

Follow steps below to program the Pattern:

1. Press the MENU key to display the main menu on the monitor. Scroll to Pattern and push the Joystick to the right to enter the Pattern menu. Or just press the PTRN key on the keyboard.
2. Select the desired Pattern to be programmed by pushing the Joystick up or down. If the Pattern is not 000, a Pattern has already been recorded. Patterns can be overwritten.
3. Press and hold down the CTRL key while controlling the camera direction and zoom with the Joystick. The dome will be automatically recorded until you release the CTRL key. Or press the IRIS Open key then the "CONTROL" displays. Move the position and the zoom position. Press the IRIS Close key then the "CONTROL" disappears.
4. To edit the "TITLE", follow the procedure of the Auto Scan above to edit titles.
5. Select "SAVE AND EXIT" and push the Joystick to the right or press the IRIS Open key. Press the ESC or IRIS Close key to exit the program without saving.

NOTE: Press the HOME key at any programmed position to delete the Pattern.

NOTE: If Pattern recording time reaches 200 seconds, it will automatically stop for a moment.

Press the PTRN key on the title field to display with the small OSD. Then the screen will show as below.

PATTERN AREA SETUP (CTRL KEY) NUMBER 01 000 00.0% EXIT(ESC TO EXIT)

The setting procedure is the same as above.

3.9 Privacy Zone

Hide up to 8 unwanted scenes in a camera.

There are two pages of Privacy Zone menu. Each page has 4 Privacy Zones.

PRIVACY ZONE SETUP (CTRL KEY)
NO		METHOD	COLOR
01	ON	BLOCK	BLACK
02	ON	BLOCK	BLACK
03	OFF	-----	BLACK
04	OFF	-----	BLACK
NEXT PAGE
SAVE AND EXIT (ESC TO CANCEL)

1. Place the cursor at the field.

2. Hold down the CTRL key displays the privacy area menu while selecting the position using the Joystick. Current position will be displayed. Release the CTRL key to complete the selection of the position. Or press the IRIS Open key then the privacy area menu displays. Move the desired position. Press the IRIS Close key then the "CONTROL" disappears.

To adjust the size, twist the Joystick or press the Tele or Wide key.

Returns to the previous menu.

PRIVACY AREA MENU (CTRL KEY) NUMBER 01 354.8 344.8 EXIT(ESC TO EXIT)

1. To turn the stored zone ON or OFF, twist the Joystick or press the Tele or Wide key.

2. Set the "COLOR": "BLACK", "WHITE", "YELLOW", "CYAN", "GREEN", "MAGENTA", "RED" or "BLUE".

3. Select "SAVE AND EXIT" and push the Joystick to the right or press the IRIS Open key. Press the ESC or IRIS Close key to exit the program without saving.

NOTE: Press the HOME key to delete programmed Privacy Zone at the title field.

3.10 Camera Menu

CAMERA SETUP

FOCUS CONTROL
WB CONTROL
AE CONTROL
CAMERA CONTROL
SHARPNESS : 03
DIGITAL ZOOM : OFF
IMAGE FLIP : OFF
PRESET FREEZE : OFF
RESOLUTION : 1080P/25
SAVE AND EXIT(ESC TO CANCEL) 

SHARPNESS The higher the value, the more edges in the picture will be enhanced. (0 \~ 10)

DIGITAL ZOOM OFF: Zoom range is limited to the optical.

2X: Zoom is extendable up to 2X of digital range.

4X: Zoom is extendable up to 4X of digital range.

8X: Zoom is extendable up to 8X of digital range.

MAX: Zoom is extendable Max digital zoom range.

IMAGE FLIP

This function turns the video output from the camera upside down and reverses it horizontally.

This option is helpful to install in the opposite side.

PRESET FREEZE

ON: the image is frozen during calling Preset.

RESOLUTION

HD-TVI Output: 1080P/30, 1080P/25, 720P/60, 720P/50, 720P/30, 720P/25

AHD Output: 1080P/30, 1080P/25

- FOCUS CONTROL

FOCUS SETUP

MODE : AUTO
SENSITIVITY : MID
FOCUS LIMIT : 1M
SAVE AND EXIT(ESC TO CANCEL) 

MODE AUTO, MANUAL, ONE PUSH, CONST MANUAL

Use manual mode in normal use.

SENSITIVITY LOW, LOW.MID, MID, MID.HIGH, HIGH

FOCUS LIMIT This d

This distance is approximate value and the focus operates from the setting value.

CAUTION: Avoid continuous, 24-hour use of the auto focus. This will shorten the lifespan of the lens.

• WB (White Balance) CONTROL

WB SETUP

MODE : AUTO
R GAIN : ---
B GAIN : ---
SAVE AND EXIT(ESC TO CANCEL) 

MODE AUTO, MANUAL, INCANDESCENT, FLUORESCENT, OUTDOOR

AUTO Computes the white balance value output using color information from the entire screen automatically.

INCANDESCENT Auto white balance mode that is compatible with incandescent lamps. FLUORESCENT Auto white balance mode that is compatible with fluorescent lamps. OUTDOOR Outdoor white balance mode MANAUL Manual mode, you can change R and B Gain manually.

R GAIN 0 \~ 255

B GAIN 0 \~ 255

R GAIN / B GAIN modes are controllable only in MANUAL Mode.

- AE CONTROL

AE SETUP

MODE : AUTO
DSS : OFF
IRIS : AUTO
SHUTTER : AUTO
BRIGHT : 10
GAIN LIMIT : 07
NIGHT SHOT : AUTO
ADDITIONAL AE
SAVE AND EXIT(ESC TO CANCEL) 

MODE AUTO, MANUAL, I.PRIO, S.PRIO

AUTO Auto exposure mode

MANUAL Variable Iris, Shutter speed

I.PRIO Variable Iris, Auto Shutter speed

S.PRIO Variable Shutter speed, Auto Iris

DSS OFF, x2 \~ x8

IRIS F1.8 \~ F32

SHUTTER 1/25 (30) \~ 1/30000

BRIGHT 0 \~ 20

GAIN LIMIT 0 \~ 7

NIGHT SHOT AUTO, ON, OFF, GLOBAL

NOTE: Values in ( ) are for NTSC Camera.

The NIGHT SHOT option removes the IR cutoff filter of the camera and makes the camera sensitive to near infrared.

AUTO Camera goes in to B&W mode at low light.

GLOBAL Controlled by the keyboard

(NOTE: GLOBAL function operates F2E protocol only)

The operator can enable NIGHT SHOT for all dome cameras at the same time.

If the NIGHT SHOT mode is set to GLOBAL, "999" + ENTER will turn Off the NIGHT SHOT mode and "888" + ENTER will turn On the NIGHT SHOT mode.

ON B/W mode

OFF Color mode

NOTE: AUTO in NIGHT SHOT function is not applied in "MANUAL" mode of AE Control.

ADDITIONAL AE

ACE OFF, LOW, MID, HIGH

WDR OFF, ON, NIGHT OFF (NOTE: When ON, BLC will be disabled.)

WDR WEIGHT LOW, MID, HIGH

BLC OFF, ON (NOTE: When ON, WDR will be disabled.)

HLC OFF, ON

HLC LEVEL 0 \~ 20

HLC COLOR BLACK, WHITE, YELLOW, CYAN, GREEN, MAGENTA, RED, BLUE

DEFOG OFF, ON

• CAMERA CONTROL

CAMERA CONROL
D->N LEVEL : 070
N->D LEVEL : 030
D/N DELAY : 03 SEC
CHROMA : 08
GAMMA : 2
DNR : MID
DIS : OFF
SAVE AND EXIT(ESC TO CANCEL) 

D->N LEVEL 0 \~ 255

N->D LEVEL 0 \~ 255

D/N DELAY 1 \~ 60 seconds

CHROMA 0 \~ 20

GAMMA 0 \~ 4

DNR OFF, LOW, MID, HIGH

DIS OFF, ON

3.11 Dome Communication

To prevent damage, each dome camera must have a unique address (ID).

The factory default setting is 1.

DOME COMMUNICATION

*
DOME ID : 0001
PROTOCOL : AUTO
BAUDRATE : 9600
PARITY : NONE
TERMINATION : OFF
SAVE AND EXIT(ESC TO CANCEL) 

DOME ID 1 \~ 3999

PROTOCOL AUTO, F2/F2E, PELCO-PD

BAUDRATE 2400, 4800, 9600, 19200, 38400 bps

PARITY NONE, EVEN, ODD

TERMINATION (RS-485) OFF, ON

3.12 Alarm

ALARM SETUP (CTRL KEY) NO PRI FUN IN OUT HLD LATCH 1 1 001 NO OUT1 03 OFF 2 1 --- OFF OFF 03 OFF 3 1 --- OFF OFF 03 OFF 4 1 --- OFF OFF 03 OFF DWELL : 03 SEC ALARM OUT SETUP SAVE AND EXIT (ESC TO CANCEL)

NO (Number) alarm input number

PRI (Priority) the lower number has higher priority (0 \~ 4)

FUN (Function) Stored function number to be called by alarm.

IN (Input) NO/NC – normally open/closed, OFF – ignore

OUT (Output) OUT1 \~ OUT2 - 5VTTL output, OFF - no output

HLD (Hold) Alarm will be held for programmed time. (03 to 99 seconds)

LATCH ON – Alarm message will remain on the screen even though alarm input is deactivated.

OFF – Alarm message will disappear from the screen after programmed hold time when alarm input is deactivated.

DWELL means the dwell time during multiple alarms, 03 to 99 seconds.

ALARM OUT SETUP OUT1 : ALARM OUT2 : 1 MIN EXIT(ESC TO EXIT)

ALARM: alarm output is operated during an alarm operation or by the short key of our keyboard.

1 \~ 5 MIN (minute): alarm output is operated during this setting time only by the function run of the dome menu or the short key of our keyboard.

NOTE: This 1 \~ 5 MIN setting is not operated by an alarm.

There are 5 levels of priority. The function can be selected by Preset, Auto scan, Pattern or Tour and "0" is the highest priority. Lower priority alarms won't be serviced until the higher priority alarm is completed. Equal priority alarms will be serviced repeatedly with the dwell time.

3.13 Dome Setup

CONFIGURATION MENU HOME FUNCTION SETUP VIEW ANGLE SETUP ORIGIN OFFSET FACTORY DEFAULT DOME RESET OSD DISPLAY SYSTEM SETUP FUNCTION RUN SYSTEM INFORMATION EXIT(ESC TO EXIT)

• HOME FUNCTION SETUP

HOME FUNCTION SETUP FUNCTION : NONE NUMBER : --- WAITING TIME : 120 SEC ENABLE : OFF SAVE AND EXIT(ESC TO CANCEL)

FUNCTION NONE, TOUR, PATTERN, AUTO SCAN, PRESET NUMBER ---

WAITING TIME 10 \~ 240 seconds

ENABLE ON, OFF

The Home Function can be set so that the camera automatically goes to Tour, Pattern, Auto Scan or Preset after the keyboard controller has been idle for a specified amount of time.

For example, if the controller is idle for 120 seconds, the camera goes to Preset 1.

Follow these steps to program the Home position:

1. Select "FUNCTION" by pushing the Joystick to the left or right to scroll through the None, Tour, Pattern, Auto Scan or Preset functions.
2. Select "NUMBER" and push the Joystick to the left or right. The recorded function number will scroll.
3. Select "WAITING TIME" and push the Joystick to the left or right to select from 10 to 240 seconds.
4. Select "ENABLE" and turn to ON or OFF by pushing the Joystick to the left or right.

• VIEW ANGLE SETUP

VIEW ANGLE SETUP

PANNING RANGE
FLIP : 90°
TILT ANGLE LIMIT : 07°
SAVE AND EXIT(ESC TO CANCEL) 

FLIP OFF, AUTO, 90°, 100°, 110°, 120°

OFF: The dome camera moves until 90° vertically.

AUTO: When the camera reaches the floor directly above the moving object, it will stop. At that time, release the Joystick instantly and pull it down again to run the auto-flip function. When you use the panning range, it is recommended to use the flip mode to AUTO. 90°, 100°, 110°, 120°: Allows the image to flip digitally when the camera moves over the setting angle vertically.

TILT ANGLE LIMIT -10° \~ 10°

This option is designed to limit the view angle as there is some obstruction in zooming out on specific areas of the tilt angle.

NOTE: Focus issues may occur in certain conditions.

PANNING RANGE

When the dome camera is installed near a wall, panning range can be limited by user.

PANNING RANGE SETUP

(CTRL KEY) 

RIGHT LIMIT : 000.0
LEFT LIMIT : 000.0
ENABLE : OFF
SWAP : OFF
AUTO PAN : ON
SAVE AND EXIT(ESC TO CANCEL) 

1. Place the dome camera under 90 degree vertically.
2. Set "RIGHT LIMIT" by pushing the Joystick to the right.
3. Set "LEFT LIMIT" by pushing the Joystick to the left.
4. Set "ENABLE" to ON to use.

To exchange the right and the left limit, set "SWAP" to ON.

To apply limits on the auto pan (endless panning), set "AUTO PAN" to ON.

NOTE: When the flip mode is 90^ , 100^ , 110^ or 120^ and you moves over 90^ vertically, the panning range operates in opposite side.

• ORIGIN OFFSET

OFFSET SETUP
(CTRL KEY)
PAN OFFSET : 000.0
TILT OFFSET : 000.0
ENABLE : OFF
SAVE AND EXIT (ESC TO CANCEL) 

This feature is useful to align a new dome camera exactly the same as the previously installed dome camera.

Dome camera's origin set and all data initialize option do not override offset values. Only the default set option in this menu will set the offset value to zero. This can be used to avoid ceiling obstructions.

• FACTORY DEFAULT

Select "FACTORY DEFAULT" to initialize the data.

FACTORY DEFAULT
ARE YOU SURE ?
CANCEL
OK 

• DOME RESET

DOME RESET
ARE YOU SURE ?
CANCEL
OK 

This feature is used to re-calibrate the orientation of a selected dome camera. Origin offset value is not affected by this function. (Offset is still valid after origin set.)

- OSD DISPLAY

OSD DISPLAY SETUP

LANGUAGE : ENGLISH
TITLE : DOMEID
DOME OSD : ON
FOCUS/EXPOSURE : OFF
COLOR : YELLOW
SAVE AND EXIT(ESC TO CANCEL) 

LANGUAGE Select the desired language.

TITLE up to 6 characters

DOME OSD ON, POSITION, ON(ZOOM), ZOOM, OFF

All display or title will disappear when DOME OSD DISPLAY is set to OFF.

FOCUS/EXPOSURE ON, OFF

ON: FOCUS and EXPOSURE displays. (AF AE)

COLOR YELLOW, GRAY, BLUE

- SYSTEM SETUP

SYSTEM SETUP

MOTOR SETUP
PASSWORD EDIT
ORIGIN CHECK
CALIBRATION : ON
PASSWORD ENABLE : OFF
MENU TIMEOUT : OFF
DOME ANSWER : OFF
PRESET FOCUS : AUTO
SAVE AND EXIT(ESC TO CANCEL) 

CALIBRATION ON (Auto origin check), OFF

PASSWORD ENABLE ON (requires the password to enter menu), OFF

MENU TIMEOUT ON (5 minutes), OFF (always menu display)

DOME ANSWER ON, OFF (no acknowledge command from the dome)

This option is helpful to escape the collision of the command using some DVR.

PRESET FOCUS AUTO, MANUAL, ONE PUSH

This option set the default mode of the focus when you save the Preset.

MOTOR SETUP

Motor Setup menu provides the pan and tilt speed of a camera. User can set the desired speed with pushing the Joystick to the left or right. During operation, pressing 153 + ON keys will change the speed to the SLOW mode and pressing 153 + OFF keys will change the speed to the NORMAL mode.

Press and hold the CTRL key and moving the Joystick will operate with the TURBO speed mode.

MOTOR SETUP

PROPORTIONAL P/T	: ON
P/T MODE	: NORMAL
SLOW PAN MAX	: 40
SLOW TILT MAX	: 40
NORMAL PAN MAX	: 90
NORMAL TILT MAX	: 90
TURBO PAN MAX	: 360
TURBO TILT MAX	: 100
SAVE AND EXIT(ESC TO CANCEL)

PROPOTIONAL P/T ON, OFF

P/T MODE SLOW, NORMAL, TURBO

SLOW PAN Maximum speed	19° ~ 90°/second
SLOW TILT Maximum speed	19° ~ 90°/second
NORMAL PAN Maximum speed	40° ~ 360°/second
NORMAL TILT Maximum speed	40° ~ 200°/second
TURBO PAN Maximum speed	200° ~ 380°/second
TURBO TILT Maximum speed	90° ~ 300°/second

PASSWORD EDIT

PASSWORD EDIT SETUP

(CTRL KEY)

INPUT PASSWORD

PASSWORD:

A B C D E F G H I J
K L M N O P Q R S T
U V W X Y Z 0 1 2 3
4 5 6 7 8 9 ( ) 

SAVE AND EXIT (ESC TO CANCEL)

You can change the password with 6-digit character in this menu.

The default password is 555555.

When the password enable is on, the input password window displays to enter the menu. At this time, move the cursor to the desired character with the Joystick and press the CTRL or IRIS Open key.

ORIGIN CHECK

If you find the dome in the wrong position during operation, execute this origin check and the dome camera will return to the right position after the origin check operation.

ORIGIN CHECK

ARE YOU SURE ?

CANCEL OK

Pressing 151 + ON keys will execute the origin check.

- FUNCTION RUN

This Function Run menu allows you to execute the function when you use a keyboard or a DVR without the function keys (Preset. Pattern, Tour and Scan).

FUNCTION RUN SETUP
(CTRL KEY)
PRESET : ---
PATTERN : ---
TOUR : ---
SCAN : ---
HOME
AUTO PAN
ALARM OUT : ----
EXIT (ESC TO EXIT) 

1. Select the desired Function by pushing the Joystick up or down.
2. Select the number by twist the Joystick in PRESET, PATTERN, TOUR and SCAN.
3. Press the CTRL or IRIS Open key to execute.

NOTE: To execute the function, you should save the function (PRESET, PATTERN, TOUR and SCAN) first.

- HOME

Select "HOME" and press the CTRL or IRIS Open key. The dome camera goes to the default position that it returns to after an assigned period of inactivity passes. The default position may be a Preset, Tour, Pattern or no action.

- AUTO PAN

You can execute the endless auto pan to turn in one direction continuously by selecting Auto-Pan.

- ALARM OUT

This function can operate only when the alarm out setup has the time in the alarm menu.

Ex)

ALARM OUT SETUP

OUT1 : ALARM
OUT2 : 1 MIN
EXIT (ESC TO EXIT) 

You press the CTRL or IRIS Open key then that alarm out operates during the setting time only.

• SYSTEM INFORMATION

SYSTEM INFORMATION

CAMERA TYPE : xxxx-Vx.xx
H/W VERSION : Vx.xx-xxxx
ROM VERSION : Vx.xxxxxxx
PROTOCOL : xxxx
BAUDRATE : 9600 (NONE)
HD B/D VERSION : Vx.xx
EXIT(ESC TO EXIT) 

The system information provides essential information about the dome camera if service is required. This screen displays the camera type and ROM version. The information on this screen cannot be modified.

Appendix A — Specifications

20x Full-HD Mini-PTZ HD-TVI & AHD CAMERA

Model 20x
IMAGE
Lens		20x4.7mm ~ 94.0mm
Angle of View 55.5° (H) ~ 3.0° (H)
Image Sensor	Type 1/2.8" SONY STARVIS CMOS sensor
	Pixels 1945 (H) x 1109 (V)
Min. Illumination		Color: 0.35 Lux @ 50IREBW: 0.013 Lux @ 50IRE
Scanning Mode Progressive Scan
Wide Dynamic Range True WDR
Day and Night Mode True D/N (Auto, Day, Night)
Noise Reduction 2DNR, 3DNR
Digital Zoom 16x
Exposure Control Auto, Manual, Shutter Priority, Iris Priority
White Balance Control Auto, Manual, Incandescent, Fluorescent, Outdoor
Back Light Compensation Yes
Image Effect Flip (Digital)
Shutter Speed		25/30fps: Auto (1/30,000 ~ x8 sec.), Manual50/60fps: Auto (1/50,000 ~ x8 sec.), Manual
VIDEO
Resolution		HD-TVI: 1080p @ 25/30fps, 720p @ 25/30/50/60fpsAHD: 1080p @ 25/30fps
Video Output HD-TVI or AHD, Composite
DIS Yes
Defog		Yes
PTZ Function
Pan Range		360° Endless
Pan Speed		Max. 380°/sec. (Preset)
Tilt Range		-10° ~ 190°
Tilt Speed		Max. 380°/sec. (Preset)
Auto Calibration		0.1° ~ 6°
Auto Scan		1 Auto Pan & 16 Auto Scans
Preset		240
Tour		8
Pattern		8
Home Function		Yes
Privacy Mask Zone		8 Programmable Zones
EXTERNAL IN/OUT
Video HD-TVI/AHD Output		BNC Jack
Video Composite Output		BNC Jack
Alarm		4 Inputs, 2 Outputs (Terminal Block)
Control		RS-485, Baud Rate: 2400 ~ 38400 bps (Default: 9600 bps)
ID (Camera Address)		1 ~ 3999

ETC
Operating Humidity 0 ~ 90%RH (Non-condensing)
Operating Temperature	-10°C ~ 50°C
Operating Temperature (with Heater)	-30°C ~ 50°C
Power Supply 12VDC, 24VAC
Power Supply (with Heater) 24VAC
Power Consumption 1.0A (12.0W) @ 12VDC or 24VAC
Power Consumption (with Heater) 1.5A (22.0W) @ 24VAC
Dimensions See dimension
Net Weight Approx. 1.6kg
Ingress Protection IP66

* Specifications are subject to change without notice *

UNIT : mm TOP VIEW Ø120 37 150 45 Ø150 Ø154 FRONT VIEW 86 Ø121 4-Ø7(Mounting Holes) 86 Cover BOTTOM VIEW

Figure – Dimension

Appendix B — Troubleshooting

If problems occur, verify the installation of the camera with the instructions in this manual and with other operating equipment. Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information.

Problem Possible Solution
No video.	Verify that power is connected to all pieces of equipment in the system.Verify that the power switches are in the ON position.Check the video connections.
Poor video quality.	Check that the BNC connectors are inserted properly.Check the voltage level of the dome camera.Cable for video is shielded.
Dome cameras lose their positions.	Reset the cameras using the Dome configuration menus.Check that the dome cameras are inserted properly in the base.Check the voltage level of the dome camera.
Camera number does not match the multiplexer number.	Check the camera ID and insert the BNC cable into the proper input of the multiplexer.

Close-up of a white security camera with a dark lens and ventilation slots (no visible text or symbols)

20x Full-HD Mini-PTZ HD-TVI & AHD CAMERA

PLEASE RECYCLE

50303980A