95-7353CH - Kit voiture Metra - Free user manual and instructions

USER MANUAL 95-7353CH Metra

Installation instructions for part 95-7353CH

Kia Rio, Rio5 2012-2015 95-7353CH

KIT FEATURES

• ISO DDIN radio provision
- Painted Charcoal

Interior view of a car dashboard with air vent, touchscreen, and control panel (no visible text or symbols)

KIT COMPONENTS

• A) Radio housing trim panel • B) Radio brackets • C) Start/Stop switch blank plate
• D) Airbag light blank plate • E) (5) #8 x 3/8" Phillips truss-head screws

A

B

C

D

E

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-7304

Antenna Adapter: • Not required

TOOLS REQUIRED

- Panel removal tool - Phillips screwdriver - Socket wrench

Table of Contents

Dash Disassembly 2

Kit Preparation....3

Kit Assembly

- ISO DDIN radio provision .... 3

CAUTION! Metra recommends disconnecting the negative battery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local Dealership for more information. All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before reconnecting the battery or cycling the ignition. Also, do not remove the factory radio with the key in the on position, or the vehicle running. It would be best to remove the key from the ignition and then wait a few seconds before removing the factory radio.

95-7353CH

Dash Disassembly

1. Unclip and remove the factory radio trim panel including the a/c vents. (Figure A)

Note: Remove the (8) retaining clips to be reused in Kit Assembly.

1. Remove (4) Phillips screws securing the radio in the dash.

2. Remove (2) Phillips screws securing the start/stop switch if equipped. (Figure B)

3. Remove (4) Phillips screws securing the storage pocket (Figure B)

4. Remove the (8) Phillips screws securing the a/c vents then unclip and remove them from the radio trim panel. (Figure B)
5. Unclip and remove the hazard switch. (Figure B)
6. Remove (3) Phillips screws securing the passenger air bag indicator. (Figure B)

Continue to kit preparation

Interior view of a car dashboard with air conditioner unit and steering wheel (no text or symbols visible)

(Figure A)

Step 3 Step 5 Step 6 Step 4 Step 7

(Figure B)

95-7353CH

Kit Preparation Kit Assembly

1. Mount the a/c vents, storage pocket, hazard switch, and passenger air bag indicator into the Radio Housing Trim Panel using screws removed in disassembly. (Figure A)

Note: For models without an airbag light, a blank plate and (3) #8 x 3/8" Phillips Truss-Head Screws are provided.

1. Mount the start/stop switch or blank plate depending on your application into the Radio Housing Trim Panel.

Note: If no switch is present there are (2) #8 X 3/8" Phillips truss head screws supplied to mount the blank plate.

1. Install the (8) panel clips removed in disassembly onto the Radio Housing Trim Panel.

Continue to kit assembly

Note: An airbag-light blank plate and screws are included for non-US models.

ght rews

(Figure A)

ISO DDIN radio provision

1. Mount the radio to the radio brackets using the screws supplied with the radio. (Figure A)
2. Mount the radio/bracket assembly into the dash.
3. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation.
4. Reassemble the dash in reverse order of disassembly.

Technical line drawing of an electronic device with mounting holes and internal components (no text or symbols)

(Figure A)

Installation instructions for part 95-7353CH

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Metra

Interior view of a car dashboard with air vent, touchscreen display, and control buttons (no visible text or symbols)

COMPONENTES DEL KIT

Interior view of a car dashboard with air conditioner unit and steering wheel (no text or symbols visible)

(Figura A) (Figura B)

Exploded view diagram of a car dashboard frame with internal components (no text or labels)

(Figura A)

Technical line drawing of an electronic device with mounting holes and internal components (no text or symbols)

(Figura A)