99-6523 - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-6523 Metra

INSTALLATION INSTRUCTIONS FOR PART 99-6523

APPLICATIONS

Ram Promaster 2014-up 99-6523

KIT FEATURES

• ISO DIN radio provision with pocket
- Custom texture

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Radio mounting brackets • D) Pocket • E) (4) White plastic panel clips
• F) (4) 5mm x 12mm Phillips Screws • G) (2) #8 x 3/8" Phillips Screws

A

BCDE

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-1784 or XSVI-6523-NAV

Antenna Adapter: • 40-VW10 or 40-EU10

Table of Contents

Dash Disassembly

- Ram Promaster 2014-up .... 2

Kit Assembly

- ISO DIN radio provision with pocket 3

TOOLS REQUIRED

• Panel removal tool • Phillips screwdriver
  • 86-5618 radio removal tool
  • 86-3528 radio removal tool

CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation. All accessories, switches, and especially air bag indicator lights must be plugged in before reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the aftermarket radio.

99-6523

Dash Disassembly

With radio delete or Single DIN factory radio:

1. Using Metra's 86-5618 radio removal tools pull the factory radio from the dash. (Figure A)
2. Remove (2) Phillips screws in bottom of dash opening.
3. Unclip and remove the factory radio trim panel.

With Double Din factory radio:

1. Using Metra's 86-3528 radio removal tools pull the factory radio from the dash.
2. Remove (2) Phillips screws from the bottom of the dash opening.

Continue to kit assembly

Line drawing of a connector with two pins inserted, showing internal structure (no text or symbols)

(Figure A)

99-6523

Kit Assembly

ISO DIN radio provision with pocket

1. Position the radio mounting brackets into the sub dash opening and secure with the (2) Phillips screws removed in disassembly. (Figure A)
2. Attach the (4) panels clips to the radio trim panel. (Figure B)
3. Mount the pocket to the radio brackets with (2) #8 x 3/8" screws supplied. Note: Pins on brackets will align with front mounting hole of pocket. (Figure C)

Technical line drawing of a car interior showing internal components and directional arrows (no text or symbols)

(Figure A)

Technical line drawing of a door frame with mounting holes and mounting points (no text or symbols)

(Figure B) (Figure D)

Technical line drawing of a rectangular electronic device with mounting flanges and a central housing (no text or symbols)

(Figure C) (Figure E)

1. Attach the radio bracket/pocket assembly to the aftermarket radio using the screws supplied with the radio or the supplied (4) Phillips screws. Note: Screws must not protrude from slot in radio brackets as interference with mounting bracket will occur when sliding radio into mounting brackets. (Figure D)
2. Locate the factory wiring harness and antenna plug in the dash. Metra recommends using the proper mating adapters from Metra and/or AXXESS.
3. Slide the aftermarket radio/pocket assembly into the radio opening between the radio mounting brackets until it clips into the opening. (Figure E)
4. Snap the radio trim panel into the opening around the aftermarket radio.

Technical line drawing of a computer case with labeled ports and components (no text or symbols)

Technical line drawing of a device with an open rear panel and internal components (no text or symbols)

INSTALLATION INSTRUCTIONS FOR PART 99-6523

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by paralling in the most recognized and supported

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

650-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP

certified technicians

Line drawing of a connector with two pins, no text or symbols present

(Figura A)

99-6523

Ensamble del kit

Line drawing of a car interior showing the engine compartment with no text or symbols

(Figura A)

Technical line drawing of a curved mechanical component with mounting holes and mounting points (no text or symbols)

(Figura B) (Figura D)

Technical line drawing of a rectangular electronic device with mounting flanges and a central casing (no text or symbols)

(Figura C) (Figura E)

Technical line drawing of a computer case with labeled ports and components (no text or symbols)

Technical line drawing of a device with an open rear panel and internal components (no text or symbols)