99-7355B - Kit voiture Metra - Free user manual and instructions

USER MANUAL 99-7355B Metra

Interior view of a car dashboard with air conditioners and a central digital display (no visible text or symbols)

Kia Sorrento (without NAV) 2014-2015

KIT FEATURES

• ISO DIN radio provision with pocket
- Painted matte black

KIT COMPONENTS

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8" Phillips screws • E) (2) #6 x 3/8" Phillips screws

AB

Line drawing of a 3D rectangular container or enclosure with internal structure (no text or symbols)

• 

• 

• 

[Non-Text]

TABLE OF CONTENTS

Dash Disassembly 2

Kit Assembly 3

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: 70-7304 • AX-HYKIA1-SWC

& AX-HYKIA-SPDIF (for amplified models)

Antenna Adapter: Not required

Steering wheel control interface: ASWC-1

TOOLS REQUIRED

- Panel removal tool • Phillips screwdriver

CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.

DASH DISASSEMBLY

1. Using soft panel tools, unsnap and remove the center dash panel surrounding the radio, disconnecting the necessary harnesses. (Figure A)
2. Remove (2) Phillips screws securing the a/c vents surrounding the factory radio, then remove the vents. (Figure B, C)

Interior view of a car dashboard with visible engine and control panel (no text or symbols)

(Figure A)

Top-down schematic of a car dashboard with control panel and side-mounted buttons (no text or labels)

(Figure B)

1. Remove (4) Phillips screws securing the radio. Slide the radio out, then unplug and remove the radio. (Figure D)

Continue to Kit Assembly

Top-down diagram of a car dashboard showing air intake and control panel (no text or labels)

(Figure C)

Top-down line drawing of a car dashboard with no visible text or symbols

(Figure D)

KIT ASSEMBLY

1. Secure the radio brackets to the pocket using the (4) #8 x 3/8" Phillips screws provided. (Figure A)

2. Secure the bracket/pocket assembly to the radio trim panel using the (2) #6 x 3/8" Phillips screws provided. (Figure B)

3. Remove the metal "DIN" sleeve and trim ring from the aftermarket radio.

4. Slide the radio into the bracket/pocket assembly, then secure it using the screws supplied with the radio. (Figure C)

5. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or Axxess. Test the radio for proper operation.

6. Secure the radio assembly to the dash using the factory screws, then reassemble the dash in reverse order of disassembly to complete the installation.

Technical line drawing of a mechanical housing or enclosure with labeled components (no text or symbols present)

(Figure A) (Figure B)

Technical line drawing of a mechanical device housing with internal components and an arrow indicating direction (no text or symbols)

Technical line drawing of a device casing with ventilation grilles and control buttons (no text or symbols)

(Figure C)

Meta®

99-7355B

INSTALLATION INSTRUCTIONS

IMPORTANT

If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling.

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Interior view of a car dashboard with air vent, grille, and control panel (no visible text or symbols)

Kia Sorrento (sin NAV) 2014-2015

CARACTERÍSTICAS DEL KIT

Line drawing of a 3D rectangular container or enclosure with no text or symbols

• 

• 

• 

[Non-Text]

INDICE

Interior view of a car dashboard and steering wheel (no text or symbols visible)

(Figura A)

Top-down technical diagram of a car dashboard with control panel and buttons (no text or labels)

(Figura B)

Interior view of a car dashboard with air vent and control panel (no text or symbols visible)

(Figura C)

Top-down technical line drawing of a car dashboard frame with control panel and buttons (no text or symbols)

(Figura D)

ENSAMBLE DEL KIT

Technical line drawing of a mechanical housing or enclosure with mounting flanges and internal components (no text or symbols)

(Figura A) (Figura B)

Technical line drawing of a mechanical device with internal components and directional arrows (no text or symbols)

Technical line drawing of a device casing with control panel and ventilation slots (no text or symbols)

(Figura C)

IMPORTANTE