GS-1008E - Network switch Edimax - Free user manual and instructions

USER MANUAL GS-1008E Edimax

No.3, Wu-Chuan 3rd Road, Wu-Gu, New Taipei City 24891, Taiwan

Email: [e-mail]

Edimax Technology Europe B.V.

Fijenhof 2, 5652 AE Eindhoven, The Netherlands

Email: [e-mail]

Edimax Computer Company

3350 Scott Blvd., Bldg.15 Santa Clara, CA 95054, USA

Live Tech Support: 1(800) 652-6776

Email: [e-mail]

Product Informaon

Package Contents

Before you start using this switch, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s):

GS-1008E Switch
- Quick Installaon Guide
● Power Adapter

Hardware Overview

Power Indicator LED Indicators EDIMAX GS-1008E 8-Port Gigabit Ethernet Desktop Switch PWR 1 2 3 4 5 6 7 8 LINK/ACT 8 7 6 5 4 3 2 1 DC IN 24 X 10/100/1000Mbps RJ-45 Ports Power Port

LED Status

LED Name	Light Status	Descripon
PWR	On	Switch is on
	O	Switch is o
LNK/ACT	On	Corresponding port is connected
	O	Corresponding port is not connected
	Flashing	Corresponding port is acve and transferring /receiving data.

Operang Environment

This switch must be installed and operated within the limits of the specied operang temperature 0 - 40°C (32 - 104°F) and humidity (10 - 90% non-condensing).

• Do not place objects on top of the unit.
• Do not obstruct any vents at the sides of the unit.
• Do not posion the unit close to any heang source such as a heater, radiator or in direct exposure to sun.
• Take care to ensure the unit does not come into contact with water. Consider using a dehumidier to reduce humidity and prevent moisture entering the unit.

Connecng to network devices

The RJ-45 ports on the switch support Auto-MDI/MDI-X which allows either straight-through or cross-over type cables to connect this switch to a workstaon or switch.

Connect one end of the network cable to the RJ-45 port on the side panel, and connect the other end of the network cable to the RJ-45 port on the network device. Follow the same procedure to connect all RJ-45 ports of the switch.

The UTP network cables must comply with EIA/TIA 568 specicaons and Category 5 standard for data transmission. The maximum length for a UTP cable segment between the switch and connected devices is 100 meters (300).

Once the network cable is connected to both ends and the aached network device is powered on, the green LNK/ACT LED should be lit.

graph LR
    A["Internet"] --> B["Romega"]
    B --> C["EXIMAX"]
    C --> D["IP Camera"]
    C --> E["Smart TV"]
    C --> F["IP Phone"]
    C --> G["Laptop"]
    C --> H["Media Player"]
    C --> I["Game Console"]

Connecng the power

Connect the power adapter to the power connector of the unit; the green power LED on the front panel should be lit.

TROUBLESHOOTING

1. Power LED is not lit.

Check if the power cord is properly connected to the external power adapter and the power source. Make sure the DC power jack is rmly plugged into the power socket of the switch.

2. Link/Acvity (LNK/ACT) LED is not lit when connected to devices.

• Ensure that the network device aached to the switch is switched on.
• Check the network cable; ensure it is properly connected to the switch and the network device.
• Check the network cable; ensure the UTP cable complied with EIA/TIA 568 and Category 5 specicaons.

[!] Contact your dealer if problems persist.

COPYRIGHT

Copyright © Edimax Technology Co., Ltd. all rights reserved. No part of this publicaon may be reproduced, transmied, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnec, opcal, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd.

Edimax Technology Co., Ltd. makes no representaons or warranes, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranes, merchantability, or tness for any parcular purpose. Any soware described in this manual is sold or licensed as is. Should the programs prove defecve following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the enre cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the soware. Edimax Technology Co., Ltd. reserves the right to revise this publicaon and to make changes from me to me in the contents hereof without the obligaon to nofy any person of such revision or changes.

The product you have purchased and the setup screen may appear slightly dierent from those shown in this QIG. The soware and specicaons are subject to change without noce. Please visit our website www.edimax.com for updates. All brand and product names menoned in this manual are trademarks and/or registered trademarks of their respective holders.

Federal Communicaon Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residential installaon. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separaon between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.

FCC Cauon

This device and its antenna must not be co-located or operang in conjuncon with any other antenna or transmier. This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon. Any changes or modicaons not expressly approved by the party responsible for compliance could void the authority to operate equipment.

Federal Communicaons Commission (FCC) Radiaon Exposure Statement

This equipment complies with FCC radiaon exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 2.5cm (1 inch) during normal operaon.

Federal Communicaons Commission (FCC) RF Exposure Requirements

SAR compliance has been established in the laptop computer(s) conguraons with PCMCIA slot on the side near the center, as tested in the applicaon for cercaon, and can be used in laptop computer(s) with substanally similar physical dimensions, construcon, and electrical and RF characteriscs. Use in other devices such as PDAs or lap pads is not authorized. This transmier is restricted for use with the speci antenna tested in the applicaon for cercaon. The antenna(s) used for this transmier must not be co-located or operang in conjuncon with any other antenna or transmier.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunicaon terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunicaons Terminal Equipment and Satellite Earth Staon Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special aenon must be paid to the dangers of electric shock and stac electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all mes to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and oce use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland.

EU Countries Not Intended for Use

None

EU Declaraon of Conformity

English: This equipment is in compliance with the essenal requirements and other relevant provisions of Direcve 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.
Français: Cet équipement est conforme aux exigences essenelles et autres dispositions de la direcve 1995/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE.
Češna: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic 1995/5/ES, 2009/125/ES, 2006/95/ES, 2011/65/ES.
Polski: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi Dyrektywą UE 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC..
Română: Acest echipament este în conformitate cu cerințele esențiale și alte prevederi relevante ale Direcvei 1995/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE.
Русский: Это оборудование соответствует основным требованиям и положениям Директивы 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.
Magyar: Ez a berendezés megfelel az alapvető követelményeknek és más vonatkozó irányelveknek (1995/5/EK, 2009/125/EK, 2006/95/EK, 2011/65/EK).
Türkçe: Bu cihaz 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC direktieri zorunlu istekler ve diğer hükümlerle ile uyumludur.
Українська: Обладнання відповідає вимогам і умовам директиви 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.
Slovenčina: Toto zariadenie spíňa základné požiadavky a d'alšie príslušné ustanovenia smerníc 1995/5/ES, 2009/125/ES, 2006/95/ES, 2011/65/ES.
Deutsch: Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.
Español: El presente equipo cumple los requisitos esenciales de la Direcva 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.
Italiano: Questo apparecchio è conforme ai requisi essenziali e alle altre disposizioni applicabili della Direva 1995/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE.
Nederlands: Dit apparaat voldoet aan de essenële eisen en andere van toepassing zijnde bepalingen van richtlijn 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC..
Português: Este equipamento cumpre os requesitos essenciais da Direcva 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.
Norsk: Dee utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direkv 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.
Svenska: Denna utrustning är i överensstämmelse med de väsentliga kraven och övriga relevanta bestämmelser i direkv 1995/5/EG, 2009/125/EG, 2006/95/EG, 2011/65/EG.
Dansk: Dee udstyr er i overensstemmelse med de væ sentligste krav og andre relevante forordninger i direkv 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.
suomen kieli: Tämä laite täyää direkivien 1995/5/EY, 2009/125/EY, 2006/95/EY, 2011/65/EY oleelliset vaamukset ja muut asiaankuuluvat määräykset.

FOR USE IN

WEEE Directive & Product Disposal

At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collecon point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal.

Declaraon of Conformity

We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives.

Equipment: 8-Port Gigabit Ethernet Switch

Model No.: GS-1008E

The following European standards for essenal requirements have been followed:

EMC Direcves 2014/30/EU

LVD Direcves 2014/35/EU

EMC

: EN55022:2010+ AC 2011

EN55024:2010

EN61000-3-2:2014

EN61000-3-3:2013

Safety (LVD)

: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011+A2:2013

Edimax Technology Co., Ltd.

No. 3, Wu Chuan 3 ^rd Road,

Wu-Ku Industrial Park,

New Taipei City, Taiwan

Date of Signature: April 2016

Signature:

Printed Name: Albert Chang

Title: Director

Edimax Technology Co., Ltd.

ΣDIMAX

NETWORKING PEOPLE TOGETHER